Leather back quiver.
-
Well first thing this morning, I went upstairs to do a little more on the quiver.
First thing, I wanted to work on the top shoulder strap some. I am going to deal with the straps as I do with a belt. I round the edges using an edger tool. They come in various sizes. For small work, I like to use my smallest size. It is just enough to round those edges for comfort.

I run the edger front and back shaving all edges.

I have found that a round hole just plain sucks for a belt buckle bar to pass through. I invested in a set of oval hole punches. After edging the piece, I will then punch holes for a fancy belt buckle I have in mind. First step is to wet the leather. Afterwards, using a ruler, mark 1" increments. Center the mark with the oval hole punch and strike with the heavy maul.

That is starting to look good.

I think I will leave the belt free of decorations, except for an understated line that should pick up the dye and give it a subtle two tone effect. I use a saddle makers groover. It is adjustable and you simply run it along the edge and the cutting part will take out a little leather. Does a nice job.

Next step and possibly my final step for the day. I have to think through on how I am going to fashion a base for the quiver. I figure it will be a bear to sew at that. Anyhow, I use some Antique gel dye with a wool dauber. I rub the dye into the leather using circular motions, and then quickly run over it with a wet sponge. The nice thing about dying leather, it picks up all the natural grains of the leather. You just never know what it will look like until you dye it. Looks like that labour intensive backgrounder tooling accomplished exactly what I wanted. This photo was taken during the dying process. After this, I kept applying dye to make everyting nice and even. It turned out great if I do say so myself.

-
thats stunning work chako
you have skills my friend 
-
Loving this thread Dan, keep up the good work.

-
Thanks. I am at a standstill right now thinking about what to do for that bottom piece.

I have a few ideas on that, just wondering what is the best way to go.
-
chako what is the cost of the tools and wear do you get your leather

-
I get my leather from a local Tandy leather dealer.
Here is Tandy's web site. They also sell a lot of the tools.
-
I think I may have figured out what I am going to do for the bottom.
I used a compass scribe to sort of measure the bottom, then I transferred the measurements to a wet piece of leather. I then increased that first measurement to make the lip that will be sewn to the bottom of the quiver.

Once I cut that out, I then cut the thickness off the sewn part. This should make sewing a lot easier, as well as eliminate that ridge that could ultimately prevent an arrow from going to the bottom. To do his, I use a skiver. I also use a V groover to remove some of the leather on the other side. This should make folding the leather a lot easier.

A dry fit and I think this should do it. Not sure until I start sewing it, but i hope it will be a good fit. The last thing to do is to put the maker's stamp. I had bought this large metal stamp a few years ago but never used it as I usualy tend to work on smaller items. I used a small metal alphabet set used to mark tools to sign my name and date. I must say, that looks nice. :D

While that is drying, I got to thinking about the hardware. I take a look at my extensive buckle collection and find the perfect buckle for it. This one even has a nice stone set into each piece.

With the hardware selected, it is time to take a look at the bottom strap. This needs the same treatment as that given to the upper half. Rounded edges, a design groove, etc... First up though, trim the one end using a special belt tip punch. These tools are handy because it is very difficult to get a belt tip shape just right by hand.

Dry fit the hardware once all of that is done.

Next up, dye the straps and bottom the same colour as the quiver. yes, that belt buckle set looks great on the dyed pieces. Note that simple groove, how it picks up the dye.

-
@Chako said:
I think I may have figured out what I am going to do for the bottom.I used a compass scribe to sort of measure the bottom, then I transferred the measurements to a wet piece of leather. I then increased that first measurement to make the lip that will be sewn to the bottom of the quiver.

Once I cut that out, I then cut the thickness off the sewn part. This should make sewing a lot easier, as well as eliminate that ridge that could ultimately prevent an arrow from going to the bottom. To do his, I use a skiver. I also use a V groover to remove some of the leather on the other side. This should make folding the leather a lot easier.

A dry fit and I think this should do it. Not sure until I start sewing it, but i hope it will be a good fit. The last thing to do is to put the maker's stamp. I had bought this large metal stamp a few years ago but never used it as I usualy tend to work on smaller items. I used a small metal alphabet set used to mark tools to sign my name and date. I must say, that looks nice. :D

While that is drying, I got to thinking about the hardware. I take a look at my extensive buckle collection and find the perfect buckle for it. This one even has a nice stone set into each piece.

With the hardware selected, it is time to take a look at the bottom strap. This needs the same treatment as that given to the upper half. Rounded edges, a design groove, etc... First up though, trim the one end using a special belt tip punch. These tools are handy because it is very difficult to get a belt tip shape just right by hand.

Dry fit the hardware once all of that is done.

Next up, dye the straps and bottom the same colour as the quiver. yes, that belt buckle set looks great on the dyed pieces. Note that simple groove, how it picks up the dye.

:o great job mate and thanks for the info, i found a site in the uk that does tools but there expensive :o -
Have you checked on eBay?
-
Leatherworking tools are expensive over here Paul, no matter where you get them from. I've looked into it a few times. That said I think if you got the right set of basic tools £50-60 should let you get underway
-
not recently chako but i will check again,
Yeah Al like most things in the uk :-\ ive missed out a few times on other sites as skint at the time :-\ i will keep looking though

-
Leather tools are expensive.
At least Tandy leather has good sales every month. I wonder if they ship to the UK?
-
I'm pretty sure there's a Tandy over here ..

-
Yeah they're here too - here you go Paul this'll get you started :P
http://www.tandyleatherfactory.co.uk/en-gbp/locale/uk/55512-01.aspx
:D :D :D :D
-
Again great work Dan..

How come you haven't made custom MT sheats for the Mods yet..??
;) -
Thanks Allan. :D
Time for another series of photographs.
Before sewing on the harness, the edges need to be finished first. I use a simple technique of wetting the edge and running a nylon slicker tool. The one shown here, I installed a Dremel shaft to hurry the job if needed. I don't use any other finish, as I find the edges come out nicely with just water, the slicker, and a bit of hard work.

With the edges all cleaned up, it is time to do some preliminary sewing.
The best most durable stitch is a saddle stitch. Lucky for me, it is also one of the easiest to do. To start off with, you need two needles. Blunt leather needles are preferred, and some waxed thread.

Next, place a needle on each end of your thread.

Now to do the Saddle stitch, you are basically doing figure eights, passing one needle through one side, and the other needle through the same hole from the other side.

After stitching the top shoulder strap, time to get onto the lower part.

Now I have the harness completed and sewn to the body.

And a look from the back. I found a bunch of small paperclips that work perfectly in holding the sides together.

Now I am thinking of doing something with the top. Might do a bit of lacing to dress it up somewhat and make the top a little stiffer. I still need to sew the main body and that bottom piece. That will be a job for another day though. I am taking a well deserved break tonight from the project.
-
Dan, you really are talented; that quiver looks cool. :D
-
Outstanding work! Can't wait to see it finished.
-
All I can say right now is that lacing sucks.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

