Charge TTi = Useless
-
Man sorry to hear of your troubles. I've had my Charge for a good while now, and it is the one I carry with me when I carry a multi. I have had zero problems with it, it is by far my favorite!
-
I also have a Chare ALX, and it works perfectly.
I'm sure that Leathermans customer service will help you out if you contact them.
Welcome to the forums by the way :) -
@PZ said:
On the second one I got this afternoon, one handle has already loosened so much that it has virtually no "locking" action. Making it about a 50/50 shot on whether the jaws will open or the handle will swing.I've lubed the hinge and even sanded and buffed the wire cutters with a Dremel...
POS.It's broke. That definately shouldn't happen. Send it back in.
-
I would tighten the handle pivots. Should cure your problem. :)
-
I think you would need to get it replaced because the issue would seem to be that the base of the pliers were ground too small so that they do not make enough friction with the handle to hold the handle in place.
My charge did not come perfect, in fact I had the exact opposite problem. My pliers were near impossible to open and close. I took some sand paper and carefully sanded the base of the pliers until eventually they worked smooth as butter.
-
Sending it to replace - you need to pay for shipping,then again,Leatherman send you something factory damage,and again you need to pay for shipping.
In finally your TTi will cost you a lot more. -
*The issue you are having with the loose handles is one I have encountered quite a few times, both on my personal mods (wave and surge) and also for mods for others. If only slightly loose, tightening the pivot bolt solves the issue sometimes. But sometimes you will find that in order to have adequate friction on the plier head, you have to tighten the pivot bolt so much that the outside implements no longer work smoothly. What I have done to remedy this is to install properly sized shims on the sides of the plier head. This makes it so you do not have to bear down on the bolts as tight while still applying friction to the plier head. Anyway, hope this helps.....
~ evil ~*
-
@CumminsDiesel said:
Sending it to replace - you need to pay for shipping,then again,Leatherman send you something factory damage,and again you need to pay for shipping.
In finally your TTi will cost you a lot more.That doesn't sound like the Leatherman we know ???
Don't they send prepaid envelopes to send faulty tools in when things go pear shaped?
I'm sure that if he explains his situation to them they will do everything they can in order to make it right
-
@threeme2189 said:
Don't they send prepaid envelopes to send faulty tools in when things go pear shaped?When the tool you've bought has an issue that requires warranty work, you foot the bill for shipping it to them. When the tool you've gotten from them as a warranty replacement has issues that make it unacceptable as a replacement you call them up and they send you out a prepaid envelope with which to return it.
At least, that was my experience. -
Sending it to replace - you need to pay for shipping,then again,Leatherman send you something factory damage,and again you need to pay for shipping.
In finally your TTi will cost you a lot more.That doesn't sound like the Leatherman we know ???
Don't they send prepaid envelopes to send faulty tools in when things go pear shaped?
I'm sure that if he explains his situation to them they will do everything they can in order to make it right
I didn't know about prepaid envelopes.
-
@PZ said:
I'm on my second one now...Both are so poorly made that the pliers jam closed constantly.
Either because the wire cutters are so rough that they jam up the tool, or because the handles "break in" after just a few minutes of playing around with it, and won't provide enough force to open the jaws of the pliers....On the second one I got this afternoon, one handle has already loosened so much that it has virtually no "locking" action. Making it about a 50/50 shot on whether the jaws will open or the handle will swing.
I've lubed the hinge and even sanded and buffed the wire cutters with a Dremel...
POS.All you need just explains your situation and the Leatherman send you a new,shiny tool.

-
@CumminsDiesel said:
Sending it to replace - you need to pay for shipping,then again,Leatherman send you something factory damage,and again you need to pay for shipping.
In finally your TTi will cost you a lot more.If the replacement Charge was less than satisfactory then I would bet that Leatheman would, somehow, eliminate any extra costs for sending them in.
-
@MeadMaker said:
If the replacement Charge was less than satisfactory then I would bet that Leatheman would, somehow, eliminate any extra costs for sending them in.Mead's right. If you let LM know that they sent you an unsatisfactory replacement, they will send you a a post paid envelope.
If there has ever been a company that stands firmly behind their product, and their warranty, it's Leatherman

-
I would tighten the handle pivots. Should cure your problem. :)
I have the specialty bits necessary (Tamper Proof torx), and I did try tightening them on the Charge. But I only have one bit in the correct size, so turning the bolt just causes the one on the other side to spin.

Deploy the pliers then tightening bolt,you can do it using just one torx.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
