Salt water Multitool
-
@tattoosteve99 said:
Yes but it has stainless steel parts too. Go ahead and make some tools with titanium. I dare you. :p.Titanium isn't the best metal for things like blades and screwdrivers that have to stay sharp or go up against other metal items. There are some super expensive beta grades that can get up to RC 52 or so, not really hard enough for a cutting edge. Still, it would make for an awesome safe queen.
The Victorinox stainless is about as stainless as stainless gets but on any salsmurfer specific SAKs I make in the future I'm going to polish the tools to a mirror finish to help keep the rust away. There's other unrustable materials that cut well like H1, Talonite and Stellite 6K that might be worth looking into but nobody would want to pay what I would charge to put something like that together. It'd be cheaper just to buy a new SAK every time one gets to corroded especially since I'd be happy to buy the old one from you at half price for the parts.
Really, if you like the SAK platform then you just need titanium liners instead of the aluminum. I could even set them up to take cellidor scales and they could be replaced as needed although I'm not sure how the brass pins and bushings hold up to the sea. As this is the second time I've heard of the problem of corroding SAK liners I might just be onto something.
-
salsmurfer. What's with all this smurf censorship?
-
Salt water?
-
Auto correct salsmurfer. Stupid auto correct

-
Did it again. Lol. Yes salt water.
-
@bushidomosquito said:
salsmurfer. What's with all this smurf censorship?clicky :D
-
@bushidomosquito said:
salsmurfer. What's with all this smurf censorship?It censors the twt part of saltwter.
-
Many thanks to all.
I, too, did think of the Swiss army knife originally, but was worried about the aluminium liners too.
I am surprised, with the great availability of cheap salt water blades, that there are not any salt resistant multitools, at a reasonable price of course.
Do you really need to buy a titanium tool?
Most diving blades manage to do without it, so the materials should be available, from non custom makers. I have had fishing editions of pocket knives before, but they are no more rust resistant than normal knives.Is that titanium swiss army knife a normal production item;
I am sure most multitools can go underwater as shown in turnsouth´s picture, but how many can remain operational after they have a few days of sea salt exposure dried on them and not rust; Also, will they need oiling again, or, can they have a special , possibly dry, lubricant.I will check one more diving shop today, see what I find.
salsmurfer. What's with all this smurf censorship?
It censors the twt part of saltwter.
I thought that was funny, pointless but funny. Good to see it covers non US swearwords too.
-
[quote
Is that titanium swiss army knife a normal production item;
[/quote]
Naaa, that's just me shamelessly promoting something I've been working on for a while. It would be perfect for you though, even the washers are marine grade bronze. :D
-
@bushidomosquito said:
Naaa, that's just me shamelessly promoting something I've been working on for a while. It would be perfect for you though, even the washers are marine grade bronze. :D
I will be happy to test it for you and you do not even have to pay me ! :D -
Naaa, that's just me shamelessly promoting something I've been working on for a while. It would be perfect for you though, even the washers are marine grade bronze. :D

I will be happy to test it for you and you do not even have to pay me ! :DWow what a great offer (rolls eyes) lol. Sorry had to do it. Hehe
-
Its better than what microsoft etc do; I am not asking for money.
-
The handles should be fine. The rest of the tool not so much:

How difficult would a H1 one piece tool be to make?
-
I was a working diver for a number of years and never found a truly good salt resistant multitool . Now I see others suggest in previous posts mention titanium single tools but no one suggested beryllium copper tools which are more common than titanium tools (not saying that they are cheap).
http://mdmetric.com/ampcocat.htm
http://findarticles.com/p/articles/mi_qa3983/is_200009/ai_n8907250/
Made targeting the powder (explosives) and the petroleum industry out of a need for non sparking tools . So a non ferrous (non corroding) alloy was created for this need . When one searches out used items the price is not as bad . I found a used tool store in Tucson not too far from me that usually had a quanity of items as there is a powder plant not too far away . You may find these worth considering .
-
It's too bad that the SOG TiNi tools had only the pliers and handles coated but the other parts are much easier to clean anyway. I would think that a TiNi Sog would provide a very good amount of corrosion resistance. The TiNi Coating is a ceramic and very durable. I have a few of these salted (pun intended) away for someone who wants to either use them for their corrosion resistance or make them shelf queens.

The picture does not do the tools justice.
Bruce
-
PVD coating is awesome and can stand up to a lot of abuse. It isn't very expensive to have it done on a lot of parts vs. one or a few parts. Someone could make a good living taking various multitools apart and sending them off to have them PVD coated and then reselling them. They do lots of other colors including a titanium aluminum nitride coating that looks like black oxide but doesn't rub off, ever. They say it has the same hardness as diamond. There are even low temperature coatings that don't affect the heat treat of blades and tools and still provide most of the protection.
-
Thanks to all.
I had a look at some Diving shops but found nothing.
H1 steel. as used in the spyrco salt series should have been an option but maybe it is not suitable for anything other than knives (too brittle, too elastic, too weak ??? I do not really know.)
A coating is good, but it has to be scratch resistant and really on a knife that you need to sharpen could not work 100%
The beryllium alloy sound interesting, but its rockwell rating is quite low (copper is soft, berillium is brittle) for a knife.
Maybe a combination of all would make one multitool that works in sea water well?
The leatherman and the SOG shown look really sweet and expensive...
-
I had a look at some Diving shops but found nothing.
H1 steel. as used in the spyrco salt series should have been an option but maybe it is not suitable for anything other than knives (too brittle, too elastic, too weak ??? I do not really know.)
A coating is good, but it has to be scratch resistant and really on a knife that you need to sharpen could not work 100%
The beryllium alloy sound interesting, but its rockwell rating is quite low (copper is soft, berillium is brittle) for a knife.
Maybe a combination of all would make one multitool that works in sea water well?
The leatherman and the SOG shown look really sweet and expensive...
H1 steel would actually make a very good plier head - very hard, but extremely tough - it doesn't get brittle, either. Spyderco had a demonstration when their H1 steel knives came out a few years ago where they bent the blade on a Pacific Salt 90 degrees in a vice and it didn't snap.
The problems would be:
- H1 is expensive
- H1 steel cannot be machined in certain ways because it's a work hardening steel. For example, Spyderco does not flat grind any H1 blades.
-
I'm going back "A couple" years here.
But after my Wave and my OHT rusting in my pocket I'm on the prowl.
I'm living in the worst conditions for a MT.
Dipped in Salt water, falling in beach sand, covered in fish slime, cutting bait, bending hooks, and even sawing drift wood.
Did anyone ever find a solution? Maybe dip my wave in some T9 BioShield efore every trip? But I don't want the oils dispensing into my pants if I'm wading
-
A buddy of mine charters out of San Diego. He's carried a SwissTool for what has to be close to 20 years..... He uses it hard and it's finish doesn't seem to bothered at all by the environment.
Sent from my iPad using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login