Need help with reshaping a blade.
-
@captain spaulding said:
Thank you sparky415 I did not even think about that. I am going to think about it while I am cleaning it and then make a decision. I will most likely end up doing it the way you suggested. Thank you for the great visual with the photos it helps incredibly.ZED it is a NO.10.
cheers mate, my next # to get
good luck , these are easy to mod, i drilled a hole for a lanyard on my #8 a week ago and might do some more work on the handle, there are plenty of mods you can do to these knives, 
just watch it though as they do mate :D

-
ZED do you know how to get the blade lock off of them. When I was cleaning mine I got some sandy material in there and now it is almost impossible to twist the lock. I need to take it off and clean it. Any ideas.
-
Here is what I did to it in the last hour. It was my first time reshaping a blade and I do not have a clamp so I had to hold it with one hand and grind with my Dremel in the other. It is much better than it was before so I am happy. I accidentally touched to the tip with the dremel so that's what that mark is on the tip. What do you think.



-
The No 10 is the best sized one ever made Captain
>:DThat is looking a lot better now!

To remove the ring (I have never done this myself so watch your fingers)
I copied this from a Utube comment
Lock the blade closed. Then grip the blade at the notch with a pair of flat nose pliers, point the front of the knife towards something soft, and pull open the blade. The blade will push the locking ring up and pop it off the knife (and if you didn't point the knife at something, it will fly across the room). It makes a sound much like the en bloc clip ejecting from an M1 Garand!
-
@sparky415 said:
The No 10 is the best sized one ever made Captain
>:DThat is looking a lot better now!

To remove the ring (I have never done this myself so watch your fingers)
I copied this from a Utube comment
Lock the blade closed. Then grip the blade at the notch with a pair of flat nose pliers, point the front of the knife towards something soft, and pull open the blade. The blade will push the locking ring up and pop it off the knife (and if you didn't point the knife at something, it will fly across the room). It makes a sound much like the en bloc clip ejecting from an M1 Garand!
Thank you for the info on removing the lock. I will let you know how it goes. I love the sound of the clip ejecting form the M1.

-
As I said I have never done this so don't blame me if there is blood

Good luck

-
Well just tried and that will not work. You cannot close the lock when the blade is in the handle as the blade blocks the lock form sliding past. Any other ideas?
You can see here how the blade blocks the lock.

-
I found this. You have to translate it though.
-
Sorry about that, I guess they must have been using the older style knives, the blades don't lock closed on the older knives
I don't know what to suggest now, maybe someone else will have a better solution for you
While you are waiting there's some more stuff about Opinals here

reply no 97 looks good to me ;)
Opinel Knifes
I was looking at a Opinel knife at a Rite Aid store. Does anyone have one of these knifes and if so what do they think of it. Mike
Multitool.Org Forum (multitool.ninja)
-
Just found this. I guess I will just pry it off.
-
Yes, it sounds like an older Opi without the additional notch in the Virobloc ring. I use a pair of C-clip pliers like that shown in the link...the jaws spread when the handles are closed. The opening the blade trick on a locked knife never worked well for me.
-
I just pried it off like in the YouTube video and it worked perfect.

-
Still got a full set of fingers? :o
-
@sparky415 said:
Still got a full set of fingers? :oSure do. Putting it back on was the hardest part. It is still tight. Any ideas anyone. Should I take it off and bend it open a bit?
-
Still tight as in hard to turn? It may be the heads of the pivot pin may be a little high or rough. Have you tried greasing the inside of the locking ring?
-
@Spork, Lord of Lime Jello! said:
Still tight as in hard to turn? It may be the heads of the pivot pin may be a little high or rough. Have you tried greasing the inside of the locking ring?Yes hard to turn. I put a bit of gun oil in the collor before I put it back on but it seemed to not help very much. Maybe I need a thicker oil. The funny thing is it would turn fine before I even started messing with it when it was all dirty.
-
Maybe the ring isn't fully seated? Do you have any light grease?
-
@Spork, Lord of Lime Jello! said:
Maybe the ring isn't fully seated? Do you have any light grease?I am pretty sure it is fully seated. No I do not have any grease. It was turning fine when I bought it. I used a rust removing bar to get the blade nice and clean. After that it felt like sand was in the collar when I turned it and it became hard to turn. I finished cleaning and shaping the blade and sprayed the blade down with oil. I took off the collar and cleaned it and oiled the inside of it then put it back together.
-
Hmm...I dunno then, unless the ring got tweaked a bit. That's pretty hard to do though.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
