Need help with reshaping a blade.
-
Just found this. I guess I will just pry it off.
-
Yes, it sounds like an older Opi without the additional notch in the Virobloc ring. I use a pair of C-clip pliers like that shown in the link...the jaws spread when the handles are closed. The opening the blade trick on a locked knife never worked well for me.
-
I just pried it off like in the YouTube video and it worked perfect.

-
Still got a full set of fingers? :o
-
@sparky415 said:
Still got a full set of fingers? :oSure do. Putting it back on was the hardest part. It is still tight. Any ideas anyone. Should I take it off and bend it open a bit?
-
Still tight as in hard to turn? It may be the heads of the pivot pin may be a little high or rough. Have you tried greasing the inside of the locking ring?
-
@Spork, Lord of Lime Jello! said:
Still tight as in hard to turn? It may be the heads of the pivot pin may be a little high or rough. Have you tried greasing the inside of the locking ring?Yes hard to turn. I put a bit of gun oil in the collor before I put it back on but it seemed to not help very much. Maybe I need a thicker oil. The funny thing is it would turn fine before I even started messing with it when it was all dirty.
-
Maybe the ring isn't fully seated? Do you have any light grease?
-
@Spork, Lord of Lime Jello! said:
Maybe the ring isn't fully seated? Do you have any light grease?I am pretty sure it is fully seated. No I do not have any grease. It was turning fine when I bought it. I used a rust removing bar to get the blade nice and clean. After that it felt like sand was in the collar when I turned it and it became hard to turn. I finished cleaning and shaping the blade and sprayed the blade down with oil. I took off the collar and cleaned it and oiled the inside of it then put it back together.
-
Hmm...I dunno then, unless the ring got tweaked a bit. That's pretty hard to do though.
-
Did you try polishing the surfaces that slide over one another with something fine, like 1200 grit sandpaper? Or maybe 1800? I used 600, 1200, and 1800 on the axles of my son's pinewood derby car, and they were practically mirror finished afterward. (We still only came in second though! :P )
-
@Heinz Doofenshmirtz said:
Did you try polishing the surfaces that slide over one another with something fine, like 1200 grit sandpaper? Or maybe 1800? I used 600, 1200, and 1800 on the axles of my son's pinewood derby car, and they were practically mirror finished afterward. (We still only came in second though! :P )They already have a pretty good polish. I have been messing with it for the last hour or so and it has become easier to turn. It is easy enough to make it usable so I am good with that right now.
-
glad you got the lock off, i was going to say what tony said but can only be done on newer locks,well you got it sorted
i watched a youtube vid on removing the lock a while back, there is a few methods, much easyer on the newer lock,
blade looks great 8) -
@Zed said:
glad you got the lock off, i was going to say what tony said but can only be done on newer locks,well you got it sorted
i watched a youtube vid on removing the lock a while back, there is a few methods, much easyer on the newer lock,
blade looks great 8)Thank you. I'm glad I could give it new life.

-
I'm glad everyone still has the right amount of fingers

I used to cut myself every time I picked mine up when I was a lad ::) :-[
-
@sparky415 said:
I'm glad everyone still has the right amount of fingers
I used to cut myself every time I picked mine up when I was a lad ::) :-[
Yea me too.

-
@sparky415 said:
I'm glad everyone still has the right amount of fingers
I used to cut myself every time I picked mine up when I was a lad ::) :-[
yep all 9 are acounted for tony
:D -
...eight...nine...nine-and-a-half... :o :ahhh
-
:D
Some of mine are a little bit shorter than they should be from getting too close to grinders/sanders/disc cutter's etc

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
