Charge Ti problem on Ebay
-
@Metropolicity said:
I've never had a problem with Jen-jen134.In fact, I've purchased a total of 19 Charge TTis from her. All have been top notch and exactly how it was described.
She has some charge TI's for sale RIGHT now.
What do you do with 19 LM Charge?? :D ???
-
You are right about it being refurbished, they don't always come with identical pivot bolts. My sideclip came back with a few different types, but all are similar. That handle just looks as if it was milled about 10 thousandths deeper than the standard. As far as opening with one hand, a lot of Leatherman tools take a bit of time to get to that point, some can arrive so stiff that you literally break a fingernail opening a tool. Others come so loose that they don't stay closed. Good thing about Charge models is that you can tighten or loosen them yourself. Just remember to loctite the fasteners back when you are done. If you attempt this, I recommend sending a message to me or any number of users here to find out exactly how this is done so you don't damage your tool or it's fasteners.
As far as the grittiness, try working the tools individually under hot running water, then THOROUGHLY dry the entire unit and oil WELL. Leatherman tools WILL rust if you leave any water in them. Remember to use an Oil such as 3 in 1, not WD40. WD40 is a great de-gunker but it will actually cause a great collection of grit because it congeals in the tool if you leave it in. Use it only as a cleaner.
Good luck with your tool!
-
I've never had a problem with Jen-jen134.
In fact, I've purchased a total of 19 Charge TTis from her. All have been top notch and exactly how it was described.
She has some charge TI's for sale RIGHT now.
What do you do with 19 LM Charge?? :D ???
For mods, gifts, general no good :)
-
@Mercury said:
You are right about it being refurbished, they don't always come with identical pivot bolts. My sideclip came back with a few different types, but all are similar. That handle just looks as if it was milled about 10 thousandths deeper than the standard. As far as opening with one hand, a lot of Leatherman tools take a bit of time to get to that point, some can arrive so stiff that you literally break a fingernail opening a tool. Others come so loose that they don't stay closed. Good thing about Charge models is that you can tighten or loosen them yourself. Just remember to loctite the fasteners back when you are done. If you attempt this, I recommend sending a message to me or any number of users here to find out exactly how this is done so you don't damage your tool or it's fasteners.As far as the grittiness, try working the tools individually under hot running water, then THOROUGHLY dry the entire unit and oil WELL. Leatherman tools WILL rust if you leave any water in them. Remember to use an Oil such as 3 in 1, not WD40. WD40 is a great de-gunker but it will actually cause a great collection of grit because it congeals in the tool if you leave it in. Use it only as a cleaner.
Good luck with your tool!
If you have the right tools, you can accellerate the breaking process by undoing the pivot screws 1/8 turn at a time.
-

Where do I get the torx with the little whole in it?
What size of torx do i need?Tnx
-
Where do I get the torx with the little whole in it?
What size of torx do i need?Tnx
The fasteners are tamper-resistant Torx and the size is T10. Leatherman uses both six-pointed and five-pointed T10 Torx fastners (most of the new tools have six pointed). Amazon.com sells tamper-resistant T10 Torx drivers fairly inexpensively. Check your tool to see which one you have (six point or five point) and buy a pair of drivers.
-
I got a couple of sets at a discount hardware store. They usually come in 1/4" but sizes, but I also have a set of micro screw drivers that came with the Tamperpoof T10.
The 5 points, which you'll never run into if you are into Charges, can be bought on ebay for a pretty steep price. I got a set of for $15 and you'll need 2 sets to get the job done right. It's only because I have a few older Waves (maybe 2004 or so) and a couple of Original Waves.
-
@Metropolicity said:
The 5 points, which you'll never run into if you are into Charges, can be bought on ebay for a pretty steep price. I got a set of for $15 and you'll need 2 sets to get the job done right. It's only because I have a few older Waves (maybe 2004 or so) and a couple of Original Waves.Here's where I got mine five point tamper-resistant Torx drivers (2 drivers for $3.99 and free shipping on orders over $25):
Six point tamper-resistant Torx drivers:
-
@Metropolicity said:
The 5 points, which you'll never run into if you are into Charges, can be bought on ebay for a pretty steep price.Why is that? I've got a Charge with three 5 point and one 6 point on each handle. I figured it was refurbed before I got it however everything looked pretty well loved/used so I'm not certain.
Anyone know what year they made the change from 5 to 6 point?
-
I believe they switched over in early 06. I have a wave from 10/06 that has 6 point ones.
I could be wrong.
-
@Metropolicity said:
I believe they switched over in early 06. I have a wave from 10/06 that has 6 point ones.I could be wrong.
You aren't.
The switch from 5-point to 6-point torx screws occured in 2006. -
I have bought 2 Charges from this seller. One was in excellent condition, and one wasn't. The one that wasn't is described here /post/501815
My second had 3 6 point srews and one 5 point and it was very tightly adjusted. It was easy to fix. The mismatched torx styles is only annoying when you disassemble it.
This seller offers a good value for these used Charges for the most part as long as you don't expect a perfect tool.
-
I have one Charge Tti from jen-jen134 that was described as perfect and it truly was. Shipping was fast and I have no complaints.
The ones she is selling at the moment have this description: "THIS ITEM IS USED BUT IN EXCELLENT CONDITIONS MAIN BLADE HAS BEEN SHARPENED".
Has anyone here ordered a knife with this description? Can You post pictures of the resharpened blade? If these are manufacturer refurbished items the sharpening could be perfect and indistinguishable (or something less than perfect). What I am interested in is the looks, are they pretty enough to give as presents?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
