gloves for mechanics?
-
Found these too late :(
Steel Edge VII Kiev, Ukraine 19. 11. 2011
Didn't Ryan need some new gloves with knuckle protection? ;)
Multitool.Org Forum (multitool.ninja)
:P
-
@Neil said:
Found these too late :(
Steel Edge VII Kiev, Ukraine 19. 11. 2011
Didn't Ryan need some new gloves with knuckle protection? ;)
Multitool.Org Forum (multitool.ninja)
:P
They made my skin crawl just looking at them!
-
:D
-
You soft whippersnappers! My dad was a mechanic for 40 years, and never wore gloves! :P
Though from growing up and seeing his bloodied and gouged knuckles, maybe gloves would have helped. ;)
-
well the otherday i was taking off a rather stiff nut with a club hammer and spanner and slipped and club hammered my hand and caught it on a nut so i do rather like gloves now! :D
-
@shamus said:
You soft whippersnappers! My dad was a mechanic for 40 years, and never wore gloves! :PThough from growing up and seeing his bloodied and gouged knuckles, maybe gloves would have helped. ;)
My father's hands are to the point where he breaks light bulbs trying to change them and wnen the time came to hold all of his newborn grandchildren he was afraid to because he did not want to hurt them he has very little feeling in his nads after beating them up so much. when he was a young man I used to watch him pop open an unopened beer can with his right hand.I say gloves are a good thing myself...
-
@shamus said:
You soft whippersnappers! My dad was a mechanic for 40 years, and never wore gloves! :P
Though from growing up and seeing his bloodied and gouged knuckles, maybe gloves would have helped. ;)
My father's hands are to the point where he breaks light bulbs trying to change them and wnen the time came to hold all of his newborn grandchildren he was afraid to because he did not want to hurt them he has very little feeling in his nads after beating them up so much. when he was a young man I used to watch him pop open an unopened beer can with his right hand.I say gloves are a good thing myself...
:ahhh :ahhh :ahhh :ahhh :ahhh
-
I am so sorry I meant to type hands..Please forgive my typo I meant no offense
Dtrain
-
-
I am so sorry I meant to type hands..Please forgive my typo I meant no offense
Dtrain
Absolutely none given I assure you, and certainly no need to apologise.

Absolutely

Made my eyes water and gave me a bloody good chuckle, but certainly no offense taken mate
Best typo in ages
:D :D :D -
I appreciate....Despite my Embarrassment I am glad that everyone had a Good laugh...Especially in the Times we live in!
-
Wish I had nads that could break light bulbs...
-
I am staying clear of that one...I have already caused enough damage to this thread..However on a serious note..My Father is proof that years in a Proffession such as a Mechanic can take it's Toll on HANDS if not properly protected as one practices his or her Proffession. As a Truck Driver I very rarely do any of the required tasks when it comes to Pre Trip/Inter Trip Inspections Hooking/Dropping my Sets or Loading/Unloading the Trailers without some sort of HAND protection.
Dtrain
-
On a serious note: I've been working on cars for 35 years, the last 25 professionally. and though my hands are calloused and have the appearance of a laborer's hands, I do take care of them. Good quality hand cleaner with moisturizers, cuts are tended to quickly, and I exercise them to prevent carpal tunnel. I also try and wash a sink full of dishes once a week or so, which really helps in keeping the stains out of my thick callouses.
-
@Dtrain said:
I am staying clear of that one...I have already caused enough damage to this thread..However on a serious note..My Father is proof that years in a Proffession such as a Mechanic can take it's Toll on HANDS if not properly protected as one practices his or her Proffession. As a Truck Driver I very rarely do any of the required tasks when it comes to Pre Trip/Inter Trip Inspections Hooking/Dropping my Sets or Loading/Unloading the Trailers without some sort of HAND protection.Dtrain
I worked as a bike mechanic when I was in college and for the most part was able to get by without gloves. Of course, bikes aren't much like cars, so it's not nearly as much of an issue. At the same time, I got plenty of bloody knuckles from pulling cranksets and gear clusters off of bikes to do bottom bracket and hub overhauls... I even learned to overhaul those old Sturmey 3 speed hubs too. :D
I eventually got careless about gloves until I was cleaning up a gear cluster in the Safety-Kleen tank without using the gloves, when some of the solvent got on a scrape I had... :ahhh Oh man did that smart!!! I was a LOT more careful about wearing gloves with the Safety-Kleen after that...
On a side note, It was always amusing to me when we'd get someone in the shop who was an auto mechanic who tried to fix his own bike... They figure after working on cars, how hard can a bicycle be? They're actually completely different animals though... there's no automotive equivalent that I know of to truing a bike wheel with a spoke wrench in a jig... there's a whole lot of voodoo in that, let me tell you!
-
@Heinz Doofenshmirtz said:
I even learned to overhaul those old Sturmey 3 speed hubs too. :DMan, I remember the first time I took one of those apart (or at least the American "borrowed" version where it was a pin and lever instead of a pull chain that shifted), and I remember my mother that day too :ahhh
-
@Heinz Doofenshmirtz said:
I even learned to overhaul those old Sturmey 3 speed hubs too. :D
Man, I remember the first time I took one of those apart (or at least the American "borrowed" version where it was a pin and lever instead of a pull chain that shifted), and I remember my mother that day too :ahhh
LOL! Yeah, I bet she was PO'd... :o There are a whole lotta small parts in one of those things...
The guy who taught me how to rebuild them had been working in bike shops for about 25 years and was a 3 speed aficionado... he actually showed me how you could rebuild them without reusing two or three of the small parts they have inside. That was a good 20 years ago though, and I haven't even seen one in nearly that long... not that I'm missing them or anything...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


>:D