Leatherman Wingman Review
-
Leatherman Wingman
Leatherman’s Wingman tool was released in 2011 as a companion tool to the slightly more expensive Sidekick. The Wingman is Leatherman’s attempt to reach the mass market with an inexpensive yet quality tool that could be sold alongside many of the cheap imports from overseas. My guess is they will be successful as the Wingman (despite the ultra cheesy advertising) is a handy, well built tool, and with a handy pocket clip, it rides along virtually unnoticed until such time as you need it. Retailing at a mere $29.99 the Wingman packs a number of features, starting with a one handed opening, partially serrated, liner locking blade. My example’s blade is extremely tight and doesn’t open without a fight. This is likely just my example, and I believe the Wingman meets Leatherman’s usual quality standards. Some folks may not care for the partial serrations, but it’s Leatherman’s stance that less expensive models (like the standard Skeletool and Freestyle models) should have serrations as they tend to stay sharper longer, and people looking for cheaper tools are less likely to maintain them. Also living on the outside of the Wingman is a pair of scissors. These are quite large for a set of multitool scissors and lock open as well. The only thing wrong with these scissors, and this is nit picking, is that they have to be pushed all the way out, release the pressure, then push them again to lock them into place. Since this tool is aimed at new users (or people who won’t pay enough attention to maintain the edge) I think this is a bit complex for someone with no experience with these tools. This is very similar to the method of opening the scissors on the Surge. Inside the handles you find a Phillips and a flathead driver on one side and a clam shell package opener, file/ruler and can/bottle opener. The clam opener is a popular item these days and seems to be gaining on popularity. It is very similar to the one found on Gerber’s Octane model and makes short work of clam shell packages. It’s amusing that the Wingman comes in a clamshell package, so you need to have the tool to get at the tool! The can/bottle opener and file/ruler are the same ones found on the Wingman’s sibling, the Sidekick, and are just about as useless. The file is too short for any serious work, and the ruler on the flip side is pretty well the same- they are fine if everything you want to measure is less than an inch long. The can/bottle opener is ok for cans, but is a bit too sharp and pointed, and tends to puncture the cap rather than lifting it off. It’s ok if there are no other options, but if you need a bottle opener with any frequency, bring another tool along. The last interesting feature of the Wingman is the radical departure from Leatherman’s typical plier head design. Like the Sidekick the pliers are sprung, which means that when you release the pressure on the handles, the jaws open up again by themselves. Personally I don’t like this feature much, and one usually only sees it on cheap copies and off brand multitools. However, Leatherman did it right, with an internal spring, meaning that it should be pretty impervious to any kind of damage. My dislike is a personal thing, and some people seem to really like it. The head also features anvil style cutters rather than the more traditional Leatherman bypass style cutters, which means the blade points come together like bolt cutter jaws rather than passing each other like scissors. The good news on this is that if you try to cut something too heavy with them and damage them, they won’t drag like damaged bypass cutters will. Overall the Wingman is a very good value for the price, and should serve a user well for many years. There’s one drawback I found on the Sidekick that really bothers me, and the Wingman suffers from this as well. On the far corner from the blade opening hole is a decorative hole cut into the handle, and when you grab the tool and try to open the blade without looking like it, you often are pushing on this handle hole rather than the blade’s opening hole. It’s quite frustrating and the hole serves no purpose other than to look cool and annoy me. If there was at least a legitimate function to it I may be able to excuse it, but there isn’t and so I can’t.Pros:
• Price
• Good sized scissors
• Good tool selectionCons:
• Decorative hole in handle feels just like blade opening hole
• File, ruler and cap lifter are virtually useless
• Sprung pliersDef
-
How did you find the scissors for cutting , I found that while they worked ok you had to kind of chase what you were cutting , there was a tendency for the jaws to push the material out .
-
I haven't noticed that yet on these, but I will do a bit more testing and let you know.
Def
-
Just in case you missed it heres a thread about the scissors /topic/32952
-
I read that, I just don't recall encountering that particular problem.
Def
-
It's no worse than any other straight edge scissor this size, I think the feeling is due to the small thumb pad produce more pressure on your thumb, so you "feel" you are using the same effort but actually not.
The metal does seems a bit thin though, this is just eyeballing it, not with a caliper.
-
That was pretty well what I was thinking. I suppose "Small thumb pad" could replace the sprung pliers in the cons list.
Def
-
I didn't think I was going to like this tool but I really love it!
I thought the scissors were broken right out of the package though.
The tool is cheap enough that I can keep it in all the places that I might need a multi. Will it replace my TTi? No... but a really nice tool for the $$$. -
Great review!

Although I do disagree with one of your cons...
I actually like the spring pliers. They are very helpful and easier to use the pliers IMO. Just because the expensive normal pliers pliers don't incorporate this feature, doesn't mean that it is without merit. All pliers should have a spring feature and I for one look for ones quality that do. Sure I've learned to work pliers without springs but why should you have to. Incorporating a good spring design like on the Wingman would make it easier to use.
I do wish that the file was longer and did away with the ruler on one side and instead had the diamond file.
I love the package opener and have used it several times now. It works great!
Ideally though, it might take getting the Sidekick and swapping tools to improve the Wingman. I'd swap out the ruler for the short serrated blade off the Sidekick. I'd also swap out the combo-edge blade of the WM for the Saw of the SK (if possible). This would leave me bladeless on the WM but I carry a plain-edge folding knife anyways so this wouldn't matter to me and the serrated blade would compliment my setup well.
And on the SK I'd have 2 blades, one combo-edge and the other plain edge. Or maybe try to work in in a full length file or full-serrated blade from another LM. I'd have to find another tool or 2 to fill the 2 slots that would be 2 dinky useless files. Maybe a the small eyeglass screwdriver bit-holder and a washer/spacer.
Overall, I'm pretty impressed with the WM. Especially when you factor in price. On the quality and fit-n-finish, I think it is actually better than my Wave. The action on opening the pliers and the tools is smoother, doesn't have that gritty feel and doesn't have the sharp edges and corners like my Wave does. The WM is very solid feeling, operates smoothly and the tools "snick" into place nicely. The retention of the tools, although not truly "locking", is quite adequate. The scissors do leave me left wanting more but they work well enough. I would have like scissors like on my Juice S2 or some of my larger Vic SAK's but it is what it is and I can work with it. And finally, I like the clip and clip it in my left rear pocket when I carry it.
One last note, I like the spring-pressure closed retention on the WM which prevents the handles from opening up in pocket. A problem I have with my Wave and Charge Ti. More of an issue when I drop them into my front pocket as coins tends to work its way into the handles.
-
I think I'm going to change the Sprung Pliers in the cos list to a thing about the scissors. I wasn't real pleased with putting that in there but there are times when one has to list any bad things they have to make three of each.
Regardless of the price of the plier tools, I just don't care for sprung pliers, and it's not a snooty thing. Perhaps that it is the result of using so many higher end plier tools that my preference is for non sprung just from a comfort aspect, but the bottom line is that it is a personal decision. Some people like them, some don't, and I wasn't comfortable putting that in there, other than in my mind, it is a mark against it.
Of course I'm not the only one that can write reviews and put them on the Main Site- check out the Offical Main Site Review Format for details on how you can have your say!
Def
-
-
No problem- I have a pretty thick skin anyway! I just wanted to address it in case anyone else thought that reading it later on, and as I said, I wasn't really comfortable putting it in there because it is a personal preference.
Besides, I wouldn't post stuff here if I didn't fully expect folks to disagree with me!

Def
-
What I can't understand is why did Leatherman leave out the lanyard ring on the wingman
Theres space there for it and they just put a washer in there ::) I know not everyone is a fan of lanyard rings but its better to have and not need then to need and not have . -
My guess would be to further differentiate models. Plus, it may only be included on the Sidekick because of the carabiner.
Def
-
@Grant Lamontagne said:
No problem- I have a pretty thick skin anyway! I just wanted to address it in case anyone else thought that reading it later on, and as I said, I wasn't really comfortable putting it in there because it is a personal preference.Besides, I wouldn't post stuff here if I didn't fully expect folks to disagree with me!

Def
I disagree!
what?
-
@Dunc said:
What I can't understand is why did Leatherman leave out the lanyard ring on the wingman
Theres space there for it and they just put a washer in there ::) I know not everyone is a fan of lanyard rings but its better to have and not need then to need and not have .Look on the back end of the handle of the Wingman/Sidekick. See those holes on the back of the handle? I started wondering why they were flush with the folding tools on the clip side of the tool, but are lined on the inside, and turned out slightly on the side of the tool with the blade and scissors. I >think< that's to allow a small ring or lanyard to be passed through there. Not certain, just a suspicion. Otherwise, I don't know why they would go through the extra expense of putting a liner piece on the inside, except to decrease wear to a lanyard. You couldn't fit 550 through there, but thinner stuff would work, I think.

In theory, the corners are turned out somewhat so a lanyard wouldn't jam up the tools when they were extended.
I'm not saying this is a fact, just my theory.
Here's my Wingman sporting the wrist strap from my camera as an example...

-
Interesting- I just thought those were more useless holes cut in them to try and make them look fancy.
I'll have to take a closer look.
Def
-
Those aren't 'useless holes'. They... uhhh... cut down on wind resistance at subsonic speed. Yeah, that's it. They improve drag coefficient.

-
Thanks for the reply , I realise that the holes in the frame make an ideal lanyard point but I still think it was a bad idea for Leatherman to out a dedicated lanyard ring on the sidekick and only a washer on the wingman .
-
@Lynn LeFey said:
Those aren't 'useless holes'. They... uhhh... cut down on wind resistance at subsonic speed. Yeah, that's it. They improve drag coefficient.
Actually, in my opinion they are worse than useless holes. Useless implies no impact on function one way or the other, while these are actually detrimental holes as I often confuse them with the blade opening hole.
Def
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login