EURIKA! Threaded tubes
-
@Raukodur said:
Resurrecting an old thread, so are these now used instead of using a hammer to peen and make rivets? Would be very useful for alox scales.Yes, bushidomosquito uses them.
5 layer brass scaled Alox pattern with bronze liners.
A light box makes a big difference...
Multitool.Org Forum (multitool.ninja)
carbon fiber and titanium Super Tinker
Carbon scales with titanium liners, tweezers and toothpick. This one is put together like a Sebenza with phosphor bronze washers and the pivot pins of a prec...
Multitool.Org Forum (multitool.ninja)
-
awesome work.
Is he the only one, or are they universally used? seem to be the much easier option, especially for alox scales.
More importantly, give than I wish to get an SAK mod made, anyone in the UK practice this?
-
Resurrecting an old thread, so are these now used instead of using a hammer to peen and make rivets? Would be very useful for alox scales.
Yes, bushidomosquito uses them.
5 layer brass scaled Alox pattern with bronze liners.
A light box makes a big difference...
Multitool.Org Forum (multitool.ninja)
Those are custom sex-bolts, not the threaded tubes referenced in this thread methinks.
carbon fiber and titanium Super Tinker
Carbon scales with titanium liners, tweezers and toothpick. This one is put together like a Sebenza with phosphor bronze washers and the pivot pins of a prec...
Multitool.Org Forum (multitool.ninja)
-
Is he the only one, or are they universally used? seem to be the much easier option, especially for alox scales.
More importantly, give than I wish to get an SAK mod made, anyone in the UK practice this?
These are 1/8 size. You have to drill out the tools and backsprings which is very tricky unless you have access to a mill.
-
Hmm, reading back through this thread, it sounds like there are body piercing jewelry pieces which would work...
Did nothing come of that?
-
I have no idea on that one sorry. All I did was to confirm they fit. Also finding out that the ones I have are a threaded shaft on the outside not inside.
-
Guess I was wrong again
I just figured these were the ones after I saw the mods. -
Although I did find some 2.5 mm threaded ones ;). Ahhhh ohhhhhh. I might let y'all in on it

-
The problem with the body piercing posts is that they are threaded very shallow and it's a problem finding them in the exact length for every tool combination. I find it easier to use the barrel pins. On the spring and backtool pins I use a 4-40 stainless screw that has an unthreaded section near the head. I can trim them to length and pivot the driver or corkscrew on the unthreaded section since they take the most torque. Then I just hide those under the scales.
-
and with the barrel pins you need to widen the holes on the implements, or they fit as things are?
-
Dumb question here, but what exactly is a barrel pin?
-
Dumb question here, but what exactly is a barrel pin?
It's not dumb if 2 people want to know :)
What are they?I'm pretty sure he's talking about knife pivots like these.
http://www.knifekits.com/vcom/product_info.php?cPath=60_83&products_id=471
-
Dumb question here, but what exactly is a barrel pin?
It's not dumb if 2 people want to know :)
What are they?I'm pretty sure he's talking about knife pivots like these.
http://www.knifekits.com/vcom/product_info.php?cPath=60_83&products_id=471
Yes that's it.
-
Ok, thanks.
-
and
http://www.knifekits.com/vcom/product_info.php?cPath=60_83&products_id=471
has them in 1/2 long which will work up to three tool layers.
-
Does that depend on how thick the tool layers are? I'm guessing the mod I want, which involves the cybertool bit driver, the pliers and scissors, would be too wide?
-
Well what you can do is put two together with 2-56 threaded rod. Then you have an inch to use. I wouldn't use any longer than that. Also I would try to make sure the joint is in-between a tool not a spring.
-
I found a el cheapo tool that has 2.5 mm barrel bolts or pivot pins. I'm planning on trying them soon so I'll let everyone know how it works out.
-
@tattoosteve99 said:
Well what you can do is put two together with 2-56 threaded rod. Then you have an inch to use. I wouldn't use any longer than that. Also I would try to make sure the joint is in-between a tool not a spring.What he said. I cut the head off a 1/4" long 2-56 screw and screwed two posts together after running them in the drill press into a coarse wetstone to make sure the ends were square and flat. Then I put them together with red locktight and trim to length and make sure the seam is in the middle of your thickest tool. 1/8" barrel pins are easy to work on since they slip right into a Dremel collet. I find the trouble to drill the tools out is far less than the trouble of trying to get 2.5mm hardware.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login