Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Black Oxide Question

Scheduled Pinned Locked Moved Leatherman Tools
18 Posts 1 Posters 14.0k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. Black Oxide Question
Black Oxide Question
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • tattoosteve99 Offline
    tattoosteve99
    Posts: 6,326
    tattoosteve99 Offline
    tattoosteve99
    wrote on last edited by
    #6 Quote Reply

      The black oxide process uses caustic soda (lye). First the stainless is activated with hydrochloric acid, then rinsed. After that it goes into a bath of 230 degree caustic solution where it stays until the desired color is reached. After that it neutralized and rinsed again. Actually BO coating is a controlled form of rust on stainless that the effect causes it to turn black. So really if any ingestion was done, it's rust (oxide). I doubt that any consequences would arise from use, or the FDA would put a warning label on it. Hope that helps.

      1 Reply Last reply
      • captain spaulding Offline
        captain spaulding
        Posts: 20,793
        captain spaulding Offline
        captain spaulding
        wrote on last edited by
        #7 Quote Reply

          Great explination Steve. :tu:

          1 Reply Last reply
          • turnsouth Offline
            turnsouth
            Posts: 2,538
            turnsouth Offline
            turnsouth
            wrote on last edited by
            #8 Quote Reply

              I had a feeling you would come through with the answer Steve :tu:

              Seems like the whole process is not unlike putting a patina on a carbon steel blade, just with stronger chemicals and neutralizers.

              1 Reply Last reply
              • Syph007 Offline
                Syph007
                Global Moderators
                Posts: 9,842
                Syph007 Offline
                Syph007
                Global Moderators
                wrote on last edited by
                #9 Quote Reply

                  Ok I was curious so I looked up the MSDS sheet for Magnetite (Fe3O4) the type of iron oxide black oxide is.

                  http://fscimage.fishersci.com/msds/09765.htm

                  Seems like mostly an 'irritant' in most cases. But it would have to come off to even be that irritant. Hot caustic applications shouldn't, but the cold method can come off more readily.

                  No LD50 was listed ( the amount mice/lab rats had to ingest to kill half of them).

                  I havent worked in chemistry for a decade, but I remember reading all the MSDS sheets for the nasty stuff I was working with at the time, and it made me change my career.

                  1 Reply Last reply
                  • kd8fre Offline
                    kd8fre
                    Posts: 182
                    kd8fre Offline
                    kd8fre
                    wrote on last edited by
                    #10 Quote Reply

                      I'm not sure about the sciencey part of it, but I have used my BO Crater to cut steak while camping more than once and I'm still here!

                      1 Reply Last reply
                      • Grant Lamontagne Offline
                        Grant Lamontagne
                        administrators
                        Posts: 67,980
                        Grant Lamontagne Offline
                        Grant Lamontagne
                        administrators
                        wrote on last edited by
                        #11 Quote Reply

                          @kd8fre said:
                          I'm not sure about the sciencey part of it, but I have used my BO Crater to cut steak while camping more than once and I'm still here!

                          The "Not Dead Yet" argument is one of my favorites! :D

                          Def


                          1 Reply Last reply
                          • tattoosteve99 Offline
                            tattoosteve99
                            Posts: 6,326
                            tattoosteve99 Offline
                            tattoosteve99
                            wrote on last edited by
                            #12 Quote Reply

                              @turnsouth said:
                              I had a feeling you would come through with the answer Steve :tu:

                              Seems like the whole process is not unlike putting a patina on a carbon steel blade, just with stronger chemicals and neutralizers.

                              Anytime. I have done countless hours of research on this.
                              @syph007
                              Yes the cold process leaves chemicals on the surface, and even if you clean it, you get 2 solutions.
                              1- the cold black oxide surface is gone
                              2- the metal stays pitted and looks horrible, also it rusts very easy

                              I know, I tried, and the cold process, without use of a better word, just plain sucks for knife use.

                              1 Reply Last reply
                              • Syph007 Offline
                                Syph007
                                Global Moderators
                                Posts: 9,842
                                Syph007 Offline
                                Syph007
                                Global Moderators
                                wrote on last edited by
                                #13 Quote Reply

                                  @tattoosteve99 said:

                                  @turnsouth said:

                                  I had a feeling you would come through with the answer Steve :tu:

                                  Seems like the whole process is not unlike putting a patina on a carbon steel blade, just with stronger chemicals and neutralizers.

                                  Anytime. I have done countless hours of research on this.
                                  @syph007
                                  Yes the cold process leaves chemicals on the surface, and even if you clean it, you get 2 solutions.
                                  1- the cold black oxide surface is gone
                                  2- the metal stays pitted and looks horrible, also it rusts very easy

                                  I know, I tried, and the cold process, without use of a better word, just plain sucks for knife use.

                                  Ya from what I heard, on stainless steel its pointless to try the cold. I dont know about regualar steel as it would be easier to oxidize, it may be better.

                                  Is the hot method an option for DIY? Ive never heard of a home version, but im sure its possible.

                                  1 Reply Last reply
                                  • tattoosteve99 Offline
                                    tattoosteve99
                                    Posts: 6,326
                                    tattoosteve99 Offline
                                    tattoosteve99
                                    wrote on last edited by
                                    #14 Quote Reply

                                      @Syph007 said:

                                      @tattoosteve99 said:

                                      @turnsouth said:

                                      I had a feeling you would come through with the answer Steve :tu:

                                      Seems like the whole process is not unlike putting a patina on a carbon steel blade, just with stronger chemicals and neutralizers.

                                      Anytime. I have done countless hours of research on this.
                                      @syph007
                                      Yes the cold process leaves chemicals on the surface, and even if you clean it, you get 2 solutions.
                                      1- the cold black oxide surface is gone
                                      2- the metal stays pitted and looks horrible, also it rusts very easy

                                      I know, I tried, and the cold process, without use of a better word, just plain sucks for knife use.

                                      Ya from what I heard, on stainless steel its pointless to try the cold. I dont know about regualar steel as it would be easier to oxidize, it may be better.

                                      Is the hot method an option for DIY? Ive never heard of a home version, but im sure its possible.

                                      Yes and no. You can DIY if you want to spend a grand or 3.

                                      1 Reply Last reply
                                      • Threeme2189 Offline
                                        Threeme2189
                                        Posts: 2,021
                                        Threeme2189 Offline
                                        Threeme2189
                                        wrote on last edited by
                                        #15 Quote Reply

                                          @tattoosteve99 said:

                                          @Syph007 said:

                                          @tattoosteve99 said:

                                          @turnsouth said:

                                          I had a feeling you would come through with the answer Steve :tu:

                                          Seems like the whole process is not unlike putting a patina on a carbon steel blade, just with stronger chemicals and neutralizers.

                                          Anytime. I have done countless hours of research on this.
                                          @syph007
                                          Yes the cold process leaves chemicals on the surface, and even if you clean it, you get 2 solutions.
                                          1- the cold black oxide surface is gone
                                          2- the metal stays pitted and looks horrible, also it rusts very easy

                                          I know, I tried, and the cold process, without use of a better word, just plain sucks for knife use.

                                          Ya from what I heard, on stainless steel its pointless to try the cold. I dont know about regualar steel as it would be easier to oxidize, it may be better.

                                          Is the hot method an option for DIY? Ive never heard of a home version, but im sure its possible.

                                          Yes and no. You can DIY if you want to spend a grand or 3.

                                          "Just" 3 grand?
                                          Sing me up :D

                                          1 Reply Last reply
                                          • dks Offline
                                            dks
                                            Posts: 21,823
                                            dks Offline
                                            dks
                                            wrote on last edited by
                                            #16 Quote Reply

                                              We can all put our money together and get one!! :D

                                              I have used gun-blue on shotguns which is a cold process and after a bit of time the, remaining, coating stops coming off (a lot cheaper than paying someone to do it for you). The coating has survived fine for many years, by the way.
                                              Of course, with a shotgun you worry about a lot more toxic chemicals than the coating on the barrels. My most recent shotgun has the hot-process coating (from looking at it) from the factory.

                                              1 Reply Last reply
                                              • tattoosteve99 Offline
                                                tattoosteve99
                                                Posts: 6,326
                                                tattoosteve99 Offline
                                                tattoosteve99
                                                wrote on last edited by
                                                #17 Quote Reply

                                                  On steel a chemical works better because it's not resistant to those chemical. Stainless is that's why it's called stainless.

                                                  1 Reply Last reply

                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                  With your input, this post could be even better 💗

                                                  Register Login

                                                  1. Home
                                                  2. Tool Talk
                                                  3. Leatherman Tools
                                                  4. Black Oxide Question
                                                  Reply
                                                  • Reply as topic
                                                  Log in to reply
                                                  COMMUNITY LINKS
                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                  Operational Funds

                                                  Help us keep the Unworkable working!

                                                  Make A Donation
                                                  November Goal: $300.00
                                                  Due Date: Nov 30
                                                  Total Receipts: $0.00
                                                  Below Goal: $300.00
                                                  0% funded
                                                  • Login

                                                  • Don't have an account? Register

                                                  • Login or register to search.
                                                  • First post
                                                    Last post
                                                  0