Super DIY SAK Liner Cutter
-
I've never seen it happen, but they say thin flakes/chips of titanium will catch fire in a nasty sort of way if they get hot enough...
-
@J-sews said:
I've never seen it happen, but they say thin flakes/chips of titanium will catch fire in a nasty sort of way if they get hot enough...Yes, there is that issue too. It burns white hot like a welding arc. I burned up my first belt sander grinding ti and thought the white sparks were cool until the dust built up so much inside that it was basically a pile of thermite burning it's way through the steel sander shell and a 3" thick oak benchtop. It melted the iron pillow block and ball bearing inside the sander like they were made of wax. I actually save the fine oily drill shavings for tinder because one spark hits it and you have a white hot orb that will dry anything out real fast. If you keep the area blown or brushed off and don't let the shavings build up it shouldn't be a problem.
-
I've never seen it happen, but they say thin flakes/chips of titanium will catch fire in a nasty sort of way if they get hot enough...
Yes, there is that issue too. It burns white hot like a welding arc. I burned up my first belt sander grinding ti and thought the white sparks were cool until the dust built up so much inside that it was basically a pile of thermite burning it's way through the steel sander shell and a 3" thick oak benchtop. It melted the iron pillow block and ball bearing inside the sander like they were made of wax. I actually save the fine oily drill shavings for tinder because one spark hits it and you have a white hot orb that will dry anything out real fast. If you keep the area blown or brushed off and don't let the shavings build up it shouldn't be a problem.
Thanks for the tips, that sounds like something I'd do. I like modding SAK knives, not making DIY thermite...lol :D I'll be more prudent about cleaning up my piles of shavings, I often get got up in what Im working on and let things get too messy.
-
Well this is how far I got making my steel template... I peened on a liner to use as a guide and this is after 3 reinforced cutting disks, and 2 grinding bits. Lots more rough shaping to do, then im hoping I can do my carbide cutter trick to shave the last 1mm off or so. If all goes well, this will be the template to make many many liners from. :D

-
And here we have the finished product through the magic of time lapse. This took a long time, lots and lots of filing and hand finishing. I did use my router for the last bit, but it still needed more course sanding in the end.
Still needs a final polish, but otherwise I now finally have a proper template made from 1/8 inch steel!




Here is a liner sitting on top of the template, fits like a glove! This may not seem too exciting, but Im pretty proud of making this by hand. Through infinite labor and time, anything is possible! :D

Now if my titanium sheet would get here I can give this a proper test!
Cheers!
-
Well I'm impressed!

-
Thanks! It should work I think, but I dont have any metals to test it on yet. Ive got hardened aluminum, brass and Ti on the way, but shipping to Canada is less than super fast. I really dont enjoy making liners by hand so Im still optimistic this will work.
-
My Titanium sheet has been back ordered for another week now, but I at least got my hardened aluminum and half hard brass in.
I thought I'd try to speed things up a bit so I printed out the outlines of the liners and glued them to the pvc protected side so I can use as a cutting guidline without having to trace them all out.

I can get 58 liners on a 12x12 piece. :D
I'm not good with a jewelers saw so I cheated and mounted a fine jewlers blade in my bench mounted scroll saw.

The scroll saw works good for speed, but its going to take me hours to cut all these out. Luckily its just rough cutting as the precision part is done with my steel template and dremel. I think the process should be to drill all holes, rough cut, mount on template and route edges.
Hopefully my plan works out or I'll have to think of something else. :D Im for sure going to make a bunch at once to build up a stockpile as this is my least favorite modding task.
-
Well I finally got to do a bit more work on these liners. My prototype cutting system needed a tweak to get good results.
I ended up drilling holes in my bench and used long peened end brass rods to hold all the parts together in a sandwich of template, material and spacers.

I only need the top plate with this system for the router to run on.


The pins extend through my workbench and I clamp them from underneath so it pulls down tight on the whole sandwich. I found this was easier to set up and I can cut 2 liners at once with this system.
-
Here is what all the layers of the sandwich look like.

Here are some finished liners! These are half hard cartridge brass. I love it, it's a nice study material.


Of course they still need an edge finish and polish, but the shape is 100%. I'm really glad this worked out as it was alot of effort to set this up! :D
-
Love it. Those slotted mandrels with emery paper in the drill press would make a great drum sander to finish those edges up fast.
-
I'm impressed!

-
Thanks! I dread making liners by hand, so this way I can at least make up a bunch and go back to the modding parts I enjoy. Plus I used up all my stock nickel silver liners so I had to figure something out. :D
-
Well I did end up making a bunch of brass liners which I'm now getting around to using. They still need finishing, but my templating jig worked just fine for roughing out the shape.

The next templating task I set my mind on was making a scissor rest piece in the shape of the keyring liner part. This just happens to make a pretty decent scissor rest and has the nice benefit of making a much stronger keyring attachment. I just used 4 of the liner size 0.040" parts as the guide and it worked just fine.


This is 12 gauge 304 stainless which just so happens to be exaclty 0.105" the same thickness as the back spring.

And here you can see how it fits with a backspring just as the original liner keyring part does.

-
Ok Ive been meaning to update this post for awhile now. I need to make a bunch more Al liners to get hard anodized so I thought Id take pictures of each stage as I go to show what I do.
So stage one is that I covered 1 sq ft of 6061 T6 Aluminum with label paper. Note that I usually just print out these templates and stick them on, but my printer is out of ink, so I just traced these on, for the same effect, but slower. I can get 54 pieces from this size.

Next I use a punch and mark one start point for drilling in each piece, just one and I always mark the same side for speed later on.

Next I rough cut them all with a jewelers saw... I'll photo that and add it, and the rest as I go.
-
It's nice to see the process.... wish I had your patience! :D
-
+1 Looking forward to the updates.

-
Ok I need to make up some more liners to get anodized red for the super popular black scale red liner look, so on to the next stage.
Basically at this point it's just a LOT of hand cutting with the jewelers saw. It's slow boring and hand cramping work, but its the best way I have to do this at the moment. Luckly I am just rough cutting these out as I cut the precise shape at a later step, its basically just cut them apart as fast as I can.




Oh and what's more exciting than watching competative darts on tv? Watching someone sawing! Thats right, watch me cut out all 54 by hand! Kidding, just 3... :D
Oh also skip the jokes about the sawing motion, Ive heard it all before from my wife making comments while watching me cut parts. :D
-
Dubious sawing action? I'm sure I don't know what you mean.


-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
