Home made camp stoves
-
I made the pilgrimage to the nearest IKEA a while back and have been fooling around with drainers. So far I have built three of them.
The first is made from the short drainer with a pot support made from 1/8" steel bar.
The second is shortened to nest with a Coleman Cookset from a tall drainer...I rolled the cut-edge slightly to stippen the rim. This is the one I've tinkered with most. Since I rarely get to burn wood, I've been turning it to use a Trangia burner as a primary heat source. Currently I've been experimenting with a strip of aluminum flashing placed inside to form a more effective windscreen for the alcohol stove.
The third is shortened to nest with an Imusa aluminum mug.



-
@Grant Lamontagne said:
I was just about to suggest that. While discussing it a few weeks ago I think Jie pointed out one that didn't require a registration or service fee.Def
Here's the post from Jie:
Survival Knives
Also I recall you need a expensive subscription with SPOT for it to work, and your request for assistance is sent to the company, who then try to pass it to ...
Multitool.Org Forum (multitool.ninja)
Apparently it's a Canadian thing, but there should be similar services for other countries as well.
Def
-
Rather than add support feet like I've seen others do, I used the cut-off pieces of the tall drainers.
I made slits down to the original holes and added a new row of vent holes. It's a pretty snug friction fit and after a couple of burn cycles, found it impossible to remove without damaging the strainer.


-
Clever

-
I've been refining this Coffee boiler setup since I got a new coffee mill. I've probably tried 8 or 9 variations of port sizes, hole patterns and flame gap so far with the Pepsi-G style stove
It's actually an aluminum greasepot of about 3 cups capacity. I used the strainer insert as a base for the pot stand...computer fan, stainless screws and hardware, aluminum tubing as spacers. The stand stows upside-down in the pot along with a roof flashing windscreen (not shown).



-
:o I'm always amazed by your stuff Spork

-
This is probably my favorite homebuilt stove stand. It's my version of Risk's CoffeeStove
It's actually meant as a twig burner, but works well with alky stoves. I sized mine to fit in a BSA messkit billy...a notch in the rim of the can allows the original plastic cup to nest with the stove. The support arms stow on the bottom of the can...held in place with the plastic lid (which can be used as a mini cutting board)
The burners are my latest build using Miller Light canbottles (sturdier than standard soda cans). Slightly modified Pepsi-G build to provide a shoulder for the simmer ring to rest...really just an 1/8" higher inner wall. The un-moderated run time on an ounce of fuel is averaging 6-7 minutes (hard boil around 5). The ring doubles the burn time. I guess technically it's not a simmer ring, but I'm hoping it will moderate the heat output enough so that I don't burn my bacon ::)



-
We need a "Spork's camp stove setups" thread.
These are just amazingly clever variations on a theme and each has its own application. Really smart design.

-
We need Spork's tutorials because his stoves look better than the originals...and everything else out there.
-
Tony plenty of twigs in my garden to try this out. Also if you want a trip to go outdoors while here in Sheffield it is only 2 miles from where I live. I also have a trang set up which includes the handle which you can use while here.
-
I like the idea of playing in your garden Mate, near the new forge ;)
-
Tested at the Meet and works well with twigs
After this picture I replaced the Ali with steel tent pegs ;) (thanks HK)
(If anyone wants to copy my one I would suggest moving the feed hole up towards the top)
-
Yes, I prefer a higher port too...keeps the flaming bits and pieces from falling out and seems to be easier to feed.
-
I will say I was impressed with Tony's deodorant can stove, worked extremely well.

-
-
These drainers are just two pounds each at Ikea (there's a taller drainer available aswell )

Smart Angel IKEA - ORDNING Cutlery Caddy, Stainless Steel
Diameter: 4 3/4" 12cms
Height: 5 3/8" 13.5cms
http://www.ikea.com/gb/en/catalog/products/30011832/ -
I just got in from the back yard where I fired up my third attempt at a wood-gas stove made from cans (a 15oz can and a larger tin can for the outside.
Here's a link to the PDF of the original version, the 'Everything Nice' wood-gas stove...
http://worldstove.com/wp-content/uploads/2009/11/EverythingNice_Stove_Instructions.pdfI've been experimenting with the simplest ways to make them with my EDC tools.
I'll see about posting a pic of the nasty looking thing if there's any interest. It is fueled by the branch litter created by our oak in the back yard, and runs for about half an hour on 2/3 of a 15oz can's worth of twigs. The wood gas stove design is simply incredible, IMO.
Here's a video someone posted on youtube of their build, if you want an idea of how simple it is.
Everything Nice wood gas stove -
Thanks Lynne
You know we will want some pictures of yours in action
I just have to finish my new 'short spork' and my little set up is just about sorted

-
Okay. As requested. It's ugly, but it works.
First pic. This is the amount of fuel required, not counting some very small twigs to get it going. Vic Tinker for scale. It rained today, so everything is damp, including the wood you see here. The tin foil will later be used as a pot wrap, and the whole mess is set atop my little Smoky Joe grill to make it safe.

Here it is during initial ignition. I've never started one of these without some kind of assistance, usually a paraffin wax soaked cotton ball. I used 2 pieces, each a quarter of a cotton ball, to get it going this time. The damp fuel made things a bit more challenging than normal. From ignition to when it's operating normally ranges from maybe 7 to ten minutes or so, depending on how the fuel catches.

Okay, so here it is at about optimal burn. It's fairly hard to see the flames. At this stage, these things put off no visible smoke, and virtually no smell. Just a flame that's about 4 to 5 inches above the can top. By this point, the external can is radiating heat.

Here's my little 1-quart camping pot set on top, before I wrap it with aluminum foil. I designed this stove with a built-in pot stand: something lacking in every other design I've seen. That's what all the square holes are around the elevated portion of the inner can.

Boil time is about 11 minutes to slow boil (not rolling boil).

And here it is post-boil. You can see the wraps I used for the pot to each side of the stove. These coals will die down to nothing in half an hour or so.

Total burn-time was about 35 minutes, not including warm-up and the point after which the flames went out, leaving only hot coals. That would be enough to boil 2 quarts of water, with additional cook time with the hot coals afterward.
And, there you have it. A stove for the cost of two cans you were going to throw away, and half an hour's work of poking holes in them. I could make a less fancy version, without the more intricate pot-stand, in about ten minutes, I think.
-
Thanks Lynn

Nice set of pictures and the built in pot stand is a great idea


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





