Gerber Dime LM Squirt PS4 comparison photos
-
-
-
Cheers for the thoughts and the pics dks.
I'm picking up my Dime on the weekend so I'll see if I agree with you after I've had a chance to play. 
-
-
So I was looking at it today and noticed that a screw was missing.
Looked on the floor and found it.The screw head had snapped off.
When? why? The tool has not been used or dropped; just opened and closed a few times yesterday and today.I assume the screw was screwd in too tight and was damaged.
The tool seems secure enough since the screw bit that stayed in seems to hold the tool together but the scales now move.
I will probably just superglue them, but I am really disappointed in the Gerber products now.
I had avoided buying them for some time because of their reputation and I think I was right.
I got 2 new Gerber products with questionable finish and quality yesterday and have a used MP600 coming, but I do not see me buying any more, at least not new.
Maybe it was an one off but I do not need their tools enough to try again.
There are better quality options out there, for me to have to put up with such problems.


-
Mine need loosening off a little, so over torquing the screws is a possibility. Didn't notice any problems with the plier teeth on mine, but I've only had a quick look till the UK crew get together on Friday. I can normally forgive a little problem on a tool, but when you get two or three or more unrelated problems on a tool - that's out of order.
The only tools I've had with multiple problems like that were from <u>Leatherman</u>.

It was a Squirt P4 and Juice CS4 to be precise, and when I got a second P4 it still had one of the two problems that my first one had - the quality on the CS4 was a joke. Personally I don't rate LM much higher than Gerber due to the quality issues I've seen from them, so I wouldn't write Gerber off too quickly as those "better options" often aren't in my opinion

-
I have had some problems with LM too, a wave, a (new) Style CS but this was totally new and unused. Also the new Gerber steady I got, which was reasonably expensive, did not impress me with its finish either; I have no-name tools that felt/looked better.
P4s and Micras, provided you clean them every so often just keep going strong.I have an MP600 coming which has a good reputation; maybe it will change my opinion.
The dealer for Gerber and LM *here * is the same person, by the way, so I know it will be minimum 20 euro (about 5000 quid.... :P) to have it replaced.
-
@dks said:
I have had some problems with LM too, a wave, a (new) Style CS but this was totally new and unused. Also the new Gerber steady I got, which was reasonably expensive, did not impress me with its finish either; I have no-name tools that felt/looked better.
P4s and Micras, provided you clean them every so often just keep going strong.I have an MP600 coming which has a good reputation; maybe it will change my opinion.
*The dealer for Gerber and LM here * is the same person, by the way, so I know it will be minimum 20 euro (about 5000 quid.... :P) to have it replaced.
That stinks! Paying more than the value of the tool to have it warrantied

My P4s both have blades with crash into the alu scales on closure and the first one has a very badly made file.The Steady hasn't impressed me one iota from what I've seen online, and Gerber have come out with many dubious designs in their time IMHO. I've found that Gerber's weakness tends to be more design based, and LM's is standard of manufacture.
I've not had a decently designed Gerber which has let me down on quality the way LM has. Even the dodgy Flik I bought which wouldn't engage was primarily a bad design on the locking pawl IMO, it's just the quality didn't compensate for that bad design. A better designed pawl (one piece instead of two) made to the same standard would have been fully functional
-
I just realised that Powernoodle had posted a similar thread to mine and did it a month earlier.

I should have really just posted my part in his thread instead of opening a new one, but since it is done now, this is the link to the original thread:
-
It wasn't until I just tried the scissors that I realised that they are, effectively, left handed. That is; the moving edge is mounted to the right hand of the fixed edge. On any normal pair of scissors it would be the other way around. Not a complaint, just an observation.
-
Very interesting. I hadn't noticed that in the pics. This moves the Dime from 'probably not' to 'maybe' for me in the future.
-
-
-
-
I had kicked around the idea of the Dime for awhile, even thought about joining the group buy before ti was released. However, now after looking at this comparison and contemplating all of the fit and finish issues, I am proudly dedicated to my PS4 even though I just snapped the plierhead off being a numbskull.

-
-
-
Very happy with mine, only reason I'd carry a squirt P4 in favour of the Dime would be is I thought I might need an eyeglasses driver or an awl
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

