Electrical Help
-
I would imagine it's most likely a loose connection given that it's a twelve year old truck and I just replaced two components in the electrical system.
I'll have to screw around a little and see what I can find. I do have a multimeter and I'll try to get a reading on the battery and see what's up with it.
I am really not looking forward to changing the alternator again... and the battery is only a couple of years old.
Def
-
@50ft-trad said:
Paul, could this be as simple as an earth fault? Would it be prudent to clean up all the earth connections to ensure there's a full circuit wherever there should be?Possibly, but it would not be my first guess.
The first thing that I would do is take the battery to any chain auto parts store and have it fully tested.

-
and in the meantime keep your eye on ebay for a tactical pink bicycle

-
So.... bad idea to drive it to my mechanic's to let him sort it out? :P
Def
-
Screw it. Its going in next week anyway to get the frame done anyway. I might as well just bring the whole thing down to him before I screw something else up.
Def
Sent from my MB860 using Tapatalk 2
-
The bright side is that if he is anything like me, he will take great pleasure in explaining how modern, complex automotive electrical systems should be left to the professionals... ;)
-
... and if he's anything like me, he'll take great pride in taking the piss out of anything you've tried so far :D :D :D :D
-
Luckily he's nothing like either of you! :P
Def
Sent from my MB860 using Tapatalk 2
-
@turnsouth said:
The bright side is that if he is anything like me, he will take great pleasure in explaining how modern, complex automotive electrical systems should be left to the professionals... ;)Heh, this is the reason I'm hesitant on changing cars. On my jeep I can do anything given time and proper space/equipment, but on a modern electronic everything car, I'm just as clueless as anyone.
But then again, as I'm getting older tinkering and fixing stuff is becoming more a chore than hobby...
-
Sorry I'm late to this.
When I did a generator to alternator conversion on my Land Rover, my recollection of the process was that output should never be over 15.5-16V. Abnormally high charging is due to a bad battery, bad regulator in the alternator or a damaged sense line/plug on the alternator (the small, usually red wire).
Also remember that a bad alternator will kill a battery, so if it's not a new battery but the alternator (or sensing harness ) is bad, you might as well change the battery too
-
Charging voltage used to be 14.7 volts under normal conditions, but on Grant's Jeep the alternator output is controlled by the powertrain control module (PCM). The PCM adjusts field current in the alternator using a two wire system, and will adjust the output voltage based on the input of several sensors (battery temp, ambient temp, engine load, etc...). The alternator output voltage can vary anywhere from 12.6 to 15 volts.
-
If the battery is open the charging voltage will go high.
-
-
If a battery cell goes open the alternator sees no load and the voltage will go high. The alternator regulator relies on the battery for help with the regulation. The battery is no good if it goes open. Your battery definitely sounds bad. The alternator runs the vehicle. All the power comes from the alternator. The battery is there pretty much just to start the vehicle. If you have a high power device like a big stereo or a winch a big altenator would be helpful. If you have 19 volts across a car battery it is open. What is the voltage when the alternator is not running?
-
Thanks for the help. As it turns out, it was corrosion on the terminal. My friend came by to help me poke around at it and after cleaning the terminals it fired right up. The new starter cranks the engine with more power than there is in a typical Asian import car!
So, it's back on the road, at least for now. It still goes in next week for the frame issues but at least its running now.
Def
Sent from my MB860 using Tapatalk 2
-
Good to hear! It's crazy how much havoc a little corrosion or a terminal that's only a tiny bit loose can cause!
-
There's 365 days marked on there already mate ;)

-
@derekmac said:
Good to hear! It's crazy how much havoc a little corrosion or a terminal that's only a tiny bit loose can cause!The stupid thing is, the negative cable was actually quite loose, and I tightened it. I took a cursory look at the positive terminal, noticed some slight corrosion and decided it wasn't significant. I then tested to make sure it was on tight and assumed it was fine.

I felt pretty damned stupid, especially since we had a beautiful weekend and all I could do was look at the Jeep and think of the things that I couldn't do- things like go off roading, kayaking or just take the dogs to the beach. I wasted a simply beautiful long weekend (temps in the 20's every day) because of just a little corrosion that took all of five minutes to fix. Needless to say I am glad to have my Jeep running again, but I am pretty angry with myself for having overlooked something so simple.
Def
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login