Alox krinking
-
A pic says more than 1000 words... ;)
All my Solo's have a non krinked blade.** I don't believe on krinked Solo's before I don't see one**
:DSomeone sort a picture out before he starts eating food off the floor because he can't see the bugs on it ;) :P
We don't want that on our conscience :D
I've no Solos in at the moment so can't assist.

-
OH Oh... I can't close the debate yet. Here is a photo of some recent Solos and a Settler for comparison. What I noticed so far is that even though these solos don't appear to have a severe crink like the settler, the profile of the grind is not semetrical look and the taper on the top vs. the bottom of the blades in this photo. This may have confused me as possible manufacturing tolerences might be such that the tip does not always meet dead center which is more of what I looked for in the past.
Using the Settler for comparison, if the Solo did have the crinked blade on the one side it would run right against the scale.
I'm now currious if they have made Solo blades that have a more semetrical taper, use the standard crinked blade, or just maufacturing tolerences are at play in my previous observations.
I'm still going to dig more when I have time.

-
Here is a shot that demonstrates either a change in the symmetry of the grind or a manufacturing tolerance. [updated image to slightly clearer one]

-
@ICanFixThat said:
Here is a shot that demonstrates either a change in the symmetry of the grind or a manufacturing tolerance.Yep I've seen variations too, but not quite that much.
I've gone through about 30-40 solos in the last few months and all were non krinked, but I wouldn't call them symmetrical. I was starting to think they just use the blades from other knives that fail that tolerance test, so no tool could go along with them in the same layer. Nothing wrong with that, that's what Id do to, since the blades for solos will still work and have a wide range of tolerances that way.
-
Crinking is not exactly bending of the blade but grinding it on one side during production so that a mating usually small blade will fit into the same slot, these two baldes pivoting on opposite ends of the knife.
-
I would like to see a pic of a non-krinked SI.
Its hard for me to imagine how a non-krinked blade wouldn't hit the awl.

-
@J Mackrel Jones said:
Crinking is not exactly bending of the blade but grinding it on one side during production so that a mating usually small blade will fit into the same slot, these two baldes pivoting on opposite ends of the knife.Yes, but how does this relate to the Solo images so far. There does not appear to be enough of a crink in most of them for an extra tool and even the one with a large variation it is still not the same as the proper crink of the Settler for an additional tool. Note, not saying there are not fully crinked Solos (that is use the same blade as the Settler), but it looks like there is more to the differences than just that.
-
Amici,
That's a very interesting find, I am going to have to investigate my Alox models for possible "krinkage" once I return to the Eagles Nest later this evening. Grazie for the heads up..Cheers,
Serge -
@ICanFixThat said:
Here is a shot that demonstrates either a change in the symmetry of the grind or a manufacturing tolerance. [updated image to slightly clearer one]I'm thinking they do a bend in the tang and a slightly off center grind to get them all the way over to clear the awl or pruner. The one on the left looks like that offset grind with the tang bend stamping process skipped for Solos. The one on the right looks like either a new one they designed to be centered or, knowing Vic, an old one they quit making. I have a blade from an old blue Solo and it's a centered blade.
-
Thank you all for the replies and interest, this is a very interesting topic to me!
@gustophersmob said:
I would like to see a pic of a non-krinked SI.Its hard for me to imagine how a non-krinked blade wouldn't hit the awl.

I consider krinking to be asymetrical grinding or twisting of the blade, as apposed to lateral bending at the tang. So to answer your question, Wenger doesn't twist nor asymetrically gring the main blade but they do bend it at the tang as apposed to Victorinox, which does.
-
@diracismyhero said:
Thank you all for the replies and interest, this is a very interesting topic to me!I would like to see a pic of a non-krinked SI.
Its hard for me to imagine how a non-krinked blade wouldn't hit the awl.

I consider krinking to be asymetrical grinding or twisting of the blade, as apposed to lateral bending at the tang. So to answer your question, Wenger doesn't twist nor asymetrically gring the main blade but they do bend it at the tang as apposed to Victorinox, which does.
Interesting, do you have any pictures?
I just checked an Wenger 90 SI, and Victorinox 90 Soldier and they look pretty close, visually hard to tell any difference, but sometimes it looked like the Vic had slightly different grind. Checked also against a much newer undated SI with branding and it also looked the same. I'll try a more scientific test later.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login