ST 300 owners club
-
@Magic Bus said:
I'm getting used to mine, lovin' it actually.It is kind of strange how the thing "tends to grow on you".
At first it feels all strange and weird in your hand, but after awhile it's really hard to put down.

EDIT: Oh, by the way, I got another membership card for the club yesterday:

:D
-
Has anyone seen the YT video of the fellow disemboweling a ST300 with a cutoff saw? He apparently received it as a warranty exchange, and was quite dissatisfied with the flex.
I'd post it, but it's just too horrid. :'( :ahhh

Hi TS, I haven't seen it, been searching just now, no joy. Any chance you can post the link?
PMed.
I thinking that posting such a video goes against the philosophy of MT.O

(At least I don't want to post it with out Dunc's, J-sews', or Def's permission)
Anyone else want a PM, just ask

Oop, a bit slow to reply here, but its perfectly fine to post video links here at MTorg.

Bob :)
-
@J-sews said:
Oop, a bit slow to reply here, but its perfectly fine to post video links here at MTorg.
Bob :)OK
WARNING: This video contains scenes of violence, which may be considered shocking, offensive, or controversial. Leading to the possibility of nausea, vomiting, sleeplessness, and incredibly horrible nightmares. It is recommended that those with a weak disposition should refrain from viewing this video.
(*and no "thumbs-up" from Vic fans *
)Leatherman SuperTool 300 vs. Makita
Translation of the video description:
"Was an exchange tool to guarantee quality but it was lousy because only the Flex, Leatherman never again! Now have a Victorinox Spirit is still the right quality!" -
Oh my god... is that guy wearing sandals, in the snow?
Now, seriously, there are some serious f***ed up people in the world. -
By about the 1:10 mark I could tell his elevator didn't go all the way to the top floor. ::) ::)
-
That would be it :D
-
By about the 1:10 mark I could tell his elevator didn't go all the way to the top floor. ::) ::)
Do you me the "Let me put my plastic covered foot on this moving multitool while I saw one inch away from it" moment?
:DAh, the Crocks moment :D
-
Another old thred revived by a new member. I am now in the ST300 club . The mailman has delivered one big, bad tool. It's soaking and the sheath is getting a spa treatment and both will be ready to go soon.
jwh
-
Leatherman Supertools...you gotta love'em

Here are my Supertools.
-
Just got one of these on the cheap from that home depot deal. I already have a core so not sure I needed this, but I notice the tools on saw handle seem a bit loosey goosey, I can even flick some of them out with one hand and saw moves/rattles when tool is closed. Is this normal or can it be adjusted without sending it back? The knurled rivets near the release mechanism seem pretty tight or have a thread sealant possibly. Anyway I dont want to pay shipping to send it to Leatherman, any thoughts?
-
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness

-
@J-sews said:
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness
Yeah i was using the core and and buck extract pliers, but there is very little meat to get a grip on, so I went with a standard needlenose and regular plier tools, was able to spin it a little, seems a little better might try it once more, but I'm getting some scratches around the screw :P. Maybe some vice grips would work better? Would be nice if they just used a stinkin hex screw
-
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness

Yeah i was using the core and and buck extract pliers, but there is very little meat to get a grip on, so I went with a standard needlenose and regular plier tools, was able to spin it a little, seems a little better might try it once more, but I'm getting some scratches around the screw :P. Maybe some vice grips would work better? Would be nice if they just used a stinkin hex screw
Amen to that!

-
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness

Yeah i was using the core and and buck extract pliers, but there is very little meat to get a grip on, so I went with a standard needlenose and regular plier tools, was able to spin it a little, seems a little better might try it once more, but I'm getting some scratches around the screw :P. Maybe some vice grips would work better? Would be nice if they just used a stinkin hex screw
Amen to that!

The Needle nose vice grip works great for this application + a little oil and its working perfectly now, I just wish their quality control wasn't so hit or miss.
-
Another odd thing I noticed about ST300 Vs. the Core(they are almost identical) is the ST300 side with 2 flatheads and awl - the thumb studs are all even, but on the Core they vary in length and are easier to get out, seems like a poor design downgrade imo.
-
@Blackbeard said:
Another odd thing I noticed about ST300 Vs. the Core(they are almost identical) is the ST300 side with 2 flatheads and awl - the thumb studs are all even, but on the Core they vary in length and are easier to get out, seems like a poor design downgrade imo.That has to do with the ST300 tool clumping feature. On the Core the tools could come out individually, so the staggered nail nicks were standard, a feature not necessary on the ST300.
One note though, the last run of Core's and any that have been factory refurbished lately will have the ST300 implements. Not a big deal, but it does defeat the "one tool at a time" feature.
-
Another odd thing I noticed about ST300 Vs. the Core(they are almost identical) is the ST300 side with 2 flatheads and awl - the thumb studs are all even, but on the Core they vary in length and are easier to get out, seems like a poor design downgrade imo.
That has to do with the ST300 tool clumping feature. On the Core the tools could come out individually, so the staggered nail nicks were standard, a feature not necessary on the ST300.
One note though, the last run of Core's and any that have been factory refurbished lately will have the ST300 implements. Not a big deal, but it does defeat the "one tool at a time" feature.
I kinda disagree, the offset nailnicks would still make it easier to chose the tool u want and put the others away faster even witht he clumping, I think they dropped the ball on this aspect, but overall I'm pretty happy with the tool especially since it cost $37 >:D
-
@Blackbeard said:
I kinda disagree, the offset nailnicks would still make it easier to chose the tool u want and put the others away faster even witht he clumping,Good point, but the redesign of the ST300 was done with the goal of having all of the tools come out at once, and then being able to flick through them with your thumb. Having the nicks all in line does give a nice wide area to grab the tools.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login