ST 300 owners club
-
That would be it :D
-
By about the 1:10 mark I could tell his elevator didn't go all the way to the top floor. ::) ::)
Do you me the "Let me put my plastic covered foot on this moving multitool while I saw one inch away from it" moment?
:DAh, the Crocks moment :D
-
Another old thred revived by a new member. I am now in the ST300 club . The mailman has delivered one big, bad tool. It's soaking and the sheath is getting a spa treatment and both will be ready to go soon.
jwh
-
Leatherman Supertools...you gotta love'em

Here are my Supertools.
-
Just got one of these on the cheap from that home depot deal. I already have a core so not sure I needed this, but I notice the tools on saw handle seem a bit loosey goosey, I can even flick some of them out with one hand and saw moves/rattles when tool is closed. Is this normal or can it be adjusted without sending it back? The knurled rivets near the release mechanism seem pretty tight or have a thread sealant possibly. Anyway I dont want to pay shipping to send it to Leatherman, any thoughts?
-
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness

-
@J-sews said:
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness
Yeah i was using the core and and buck extract pliers, but there is very little meat to get a grip on, so I went with a standard needlenose and regular plier tools, was able to spin it a little, seems a little better might try it once more, but I'm getting some scratches around the screw :P. Maybe some vice grips would work better? Would be nice if they just used a stinkin hex screw
-
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness

Yeah i was using the core and and buck extract pliers, but there is very little meat to get a grip on, so I went with a standard needlenose and regular plier tools, was able to spin it a little, seems a little better might try it once more, but I'm getting some scratches around the screw :P. Maybe some vice grips would work better? Would be nice if they just used a stinkin hex screw
Amen to that!

-
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness

Yeah i was using the core and and buck extract pliers, but there is very little meat to get a grip on, so I went with a standard needlenose and regular plier tools, was able to spin it a little, seems a little better might try it once more, but I'm getting some scratches around the screw :P. Maybe some vice grips would work better? Would be nice if they just used a stinkin hex screw
Amen to that!

The Needle nose vice grip works great for this application + a little oil and its working perfectly now, I just wish their quality control wasn't so hit or miss.
-
Another odd thing I noticed about ST300 Vs. the Core(they are almost identical) is the ST300 side with 2 flatheads and awl - the thumb studs are all even, but on the Core they vary in length and are easier to get out, seems like a poor design downgrade imo.
-
@Blackbeard said:
Another odd thing I noticed about ST300 Vs. the Core(they are almost identical) is the ST300 side with 2 flatheads and awl - the thumb studs are all even, but on the Core they vary in length and are easier to get out, seems like a poor design downgrade imo.That has to do with the ST300 tool clumping feature. On the Core the tools could come out individually, so the staggered nail nicks were standard, a feature not necessary on the ST300.
One note though, the last run of Core's and any that have been factory refurbished lately will have the ST300 implements. Not a big deal, but it does defeat the "one tool at a time" feature.
-
Another odd thing I noticed about ST300 Vs. the Core(they are almost identical) is the ST300 side with 2 flatheads and awl - the thumb studs are all even, but on the Core they vary in length and are easier to get out, seems like a poor design downgrade imo.
That has to do with the ST300 tool clumping feature. On the Core the tools could come out individually, so the staggered nail nicks were standard, a feature not necessary on the ST300.
One note though, the last run of Core's and any that have been factory refurbished lately will have the ST300 implements. Not a big deal, but it does defeat the "one tool at a time" feature.
I kinda disagree, the offset nailnicks would still make it easier to chose the tool u want and put the others away faster even witht he clumping, I think they dropped the ball on this aspect, but overall I'm pretty happy with the tool especially since it cost $37 >:D
-
@Blackbeard said:
I kinda disagree, the offset nailnicks would still make it easier to chose the tool u want and put the others away faster even witht he clumping,Good point, but the redesign of the ST300 was done with the goal of having all of the tools come out at once, and then being able to flick through them with your thumb. Having the nicks all in line does give a nice wide area to grab the tools.
-
I kinda disagree, the offset nailnicks would still make it easier to chose the tool u want and put the others away faster even witht he clumping,
Good point, but the redesign of the ST300 was done with the goal of having all of the tools come out at once, and then being able to flick through them with your thumb. Having the nicks all in line does give a nice wide area to grab the tools.
Well I also don't agree with Joe Leatherman there...If you have both tools, do a side by side test, you can deploy the core tools 5x faster and easier than the supertool, so I say leave the clumping to SOG. maybe they designed it for ogres or the giants in the nba or better yet to save $.
-
Perhaps a bit of thread necromancy is in order? I felt asking this question fit better here than a new thread. My ST300's pivot has the distinct problem of being functionally loose, until I squeeze the handles really tight, then the head is tight to the point the handles almost want to close, until I open it and close it fully a couple times, and it returns to normal. Any ideas?
-
Is this a new problem or was it that way since you got it? Maybe the screw isn't sitting right?
In any case, I just wanted to use this smiley. :D

-
Hey, I'm in this one now too! Got a BO ST300 in a trade a few weeks ago!

-
Well i finally bought one yesterday. Its on its way, cant wait for it to get here. I have no idea what version it is but the seller said '2012' model. Its been over a year that i since decided i wanted one and liked what i saw then so i have no idea if theres been any updates. Hopefully its still made in USA (fingers crossed)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
