What Did You Use Your Multitool For Today?
-
Today I used my mum's SOG Powerlock's saw to remove a dead branch; it worked surprisingly well.
-
I WOULD have used my Cool Tool to tighten the my handlebars after a fall, but I forgot to put it in my seat bag.

-
Used my Spirit X to disassemble my desktop speakers at work so I could resolder the headphone jack connector because the solder joints were bad. The philips driver worked well.
Someone had brought in their soldering iron so it saved me from bringingthem home this weekend. Resoldered the connections and reassembled.
Sent from my MB860
-
Used the spirit x to re-tighten a door handle. Can opener/small screwdriver did it's job. :)
-
today I was at a picnic. A whole bunch of us are smokers, but there wasn't a butt can/ashtray in sight! took a couple of empty soda cans and used the can opener on my Evo16 to cut the tops off. Problem solved!
-
Had to build my wife's sewing table (flatpack) today. Too lazy to go out to the shed for tools, so my Charge and Skeletool did all the work :)
-
Replaced the light over the kitchen sink Friday using a SwissTool and Leatherman Es4
-
Used the New Soldier's awl to clean a screw. And I dropped the SAK. And the end of the awl chipped off.

-
SwissTool was a huge help in replacing the motor in a paint shaker.

-
I use my Vic Spirit everyday. EVERYDAY. I have a thread on EDCF about it, but here are some highlights from the last couple of months.
...I had to drill a 3/16th hole in a SumpPump discharge pipe. Why bother getting a cordless drill and a bit and a battery when...VIC.[ATTACH=full]7014[/ATTACH]
(That was a picture of my vic awl poking a hole in the 1.5" PVC discharge pipe.)Toilet handle was missing a cotter pin, so VIC!
This
(a pic of a wire flaper hook)
[ATTACH=full]7018[/ATTACH]Became this
(a makeshift cotterpin)
[ATTACH=full]7019[/ATTACH]Because of this
(my Vic)
[ATTACH=full]7020[/ATTACH]Which saved me yet another trip to the truck.
Used the Vic as a hammer again today. Nothing major, just some plastic anchors when installing a new Frost Proof Hose faucet.
(pic of me tappin =g in some plastic anchors)
[ATTACH=full]7078[/ATTACH]Also had to get the Vic's bit extension in the drill to allow the chuck to not rub the handle of the faucet. Its hard to screw the screws in if the driver head is at an angle. It'd just strip the screws and rub marks on the plastic handle. Yep, the Vic saved me 2 trips to the truck on that job.

[ATTACH=full]7079[/ATTACH]The awl helped remove the cartridge clip from a moen Tub & Shower valve. No better tool for that. I always goto the Vic Awl!

Used it to reconnect my CB radio after the repair shop replaced my battery cable and left it off.
This is a dramatic reenactment...

Also had to retract the hood's locking mechanism with the flathead. Have to do it every time I pop the hood:)

Hoping the pics show up. I'll edit if they don't.
EDIT: some did, some didn't. I labeled the ones that didn't though they were pretty self explanitory.
If you'd like to see my thread its here
-
I used the medium flathead on the Juice S2 to replace the battery in my car's fob. Then I used the same flathead (since it was already out) to scrape a decade's worth of crud out of the fob before reassembling.
At home, I have the Juice S2, an original PST, and a Vic Tinker on my living room table. When something arises, I grab whatever seems like the most likely needed tool, and go to it.
-
I used my Classic scissors to open some medicine packets and to cut some tags and zip ties.
-
Used the Spirit X to repair a cooler which cools beer for the tap. Only did it because :
A: It's my girlfriends pub,
B: Beer, for chrissakes :D -
Today I used my Supertool 300's beefy jaws to do a quick repair of my kitchen sink faucet. The spray tip had come loose so it was really just re-tightening the thing, and voila, fixed! When my girlfriend got home, she asked me to fix the sink, so I told her I already did!
-
used climbers' twezers to remove bee stinger from my dad's eyebrow (ow!). worked really good only slipped off stinger once but it was my fault cause i didnt wanna squeeze stinger too hard and squeeze more venom in, 10 of 10 performance
-
Been on a crosscountry move the last three days, with two left. My BO wave has been by my side the whole time and i have used the hell out of it for everything from furniture disassembly(praise the bit extender!!) to cutting rope to snipping my son's straw down to size when we stop to eat. This tool has cemented itself as a companion.
Sent from my myphone using Crapatalk
-
Today I've changed old teared mosquito net's from window's...
I must say that I've beaten up my Pico Widgy Pry bar to take out old rusty painted nails which digged in the wood... And it passed with flying colors!!! Maybe Atwood, JRP, PTX or some other are fancier, but I bet they would just eat the dust behind this little dude...
The curve is perfect, sharpness of tips is just right... I've beaten it with hammer, pryied with pliers... Nothing!! It looks as new!!!
I'm contemplating on getting Atwood Keyton, and have PTX Brewzer and Piranha... Though I'll get me the rest of two sizes of CC Widgy Pry Bar!!! They are awesome!!
Together with this I've used my Spirit, also pulling out nails, and stretshing the new SS mosquito net!!
Awesome job today!!
-
Used the serrated blade on the Rebar to cut some card board. :)
-
Used the Spirit X to fix a sunscreen, which closed on the slightest breeze...
-
Well, I took the weekend off, and just vegged, but Friday, I put the Charge ALX to good use, repairing a handle on a lawn mower.
STILL amazes me, those simple little things you never think of, and how the MT takes care of them . You'd think it was made for that... :D

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login