What Did You Use Your Multitool For Today?
-
Amici,
I used the pliers from a Victorinox Craftsman and a Wenger S557 to bend a small chain link back together that had somehow separated apart.Cheers,
Serge -
Used the awl on the Trekker to make holes in a new wood-gas stove. Used the Sheffield 12010 to handle sharp edges of cans while making the wood-gas stove. Then, I used the Trekker's blade and saw to cut wood to fill the stove for first testing. The stove works great.
-
Used the large blade on my deluxe tinker and a signal mirror while sitting at my desk to shave a small patch of whiskers under my nose that I had missed when shaving.
Sent from my MB860
-
I replaced the lace on one of my 3 y.o. daughter's boots. It was actually a bit of work... they are Keens and have the elastic laces that are fixed into the shoe. Used my Compact to remove the laces from the lanyard lock that held them together, and my Skeletool to press the lock back together after installing the new lace. Had to use a pair of hemostats to pull the new lace through the very tiny holes on the shoe for the lace.
-
Used my Victorinox Spirit to pull a piece of nail out of the left rear tire of my car, luckily it didn't puncture it (at least I think it didn't, I'll check it again tomorow morning just to make sure ... ::)).
No way I could have pulled it out by hand, it sat horizontal in a groove of the tyre, but the Spirit got it out in no time 8).
-
Just used my TTi to shape a coathanger so i could help someone get into their car, of course the keys were in the ignition. Silly teenagers, when will they learn?
-
Used my Skeletool to tighten up a mirror on a motorcycle , opposite threads are a real pain >:D, did the job fine , but not good for the chrome , so must start to carry a wrench. Which I have just seen the logic of , thanks to this forum :).
-
Used my TTi to take the cover off my A/C condenser. Coils were pretty dirty(clogged really) so i hosed them off, but the unit still isn't cooling the house. My A/C skills are minimal so I guess a call to a technician is in order, my wife and mother in law can't stand the heat!
-
Today I used my mum's SOG Powerlock's saw to remove a dead branch; it worked surprisingly well.
-
I WOULD have used my Cool Tool to tighten the my handlebars after a fall, but I forgot to put it in my seat bag.

-
Used my Spirit X to disassemble my desktop speakers at work so I could resolder the headphone jack connector because the solder joints were bad. The philips driver worked well.
Someone had brought in their soldering iron so it saved me from bringingthem home this weekend. Resoldered the connections and reassembled.
Sent from my MB860
-
Used the spirit x to re-tighten a door handle. Can opener/small screwdriver did it's job. :)
-
today I was at a picnic. A whole bunch of us are smokers, but there wasn't a butt can/ashtray in sight! took a couple of empty soda cans and used the can opener on my Evo16 to cut the tops off. Problem solved!
-
Had to build my wife's sewing table (flatpack) today. Too lazy to go out to the shed for tools, so my Charge and Skeletool did all the work :)
-
Replaced the light over the kitchen sink Friday using a SwissTool and Leatherman Es4
-
Used the New Soldier's awl to clean a screw. And I dropped the SAK. And the end of the awl chipped off.

-
SwissTool was a huge help in replacing the motor in a paint shaker.

-
I use my Vic Spirit everyday. EVERYDAY. I have a thread on EDCF about it, but here are some highlights from the last couple of months.
...I had to drill a 3/16th hole in a SumpPump discharge pipe. Why bother getting a cordless drill and a bit and a battery when...VIC.[ATTACH=full]7014[/ATTACH]
(That was a picture of my vic awl poking a hole in the 1.5" PVC discharge pipe.)Toilet handle was missing a cotter pin, so VIC!
This
(a pic of a wire flaper hook)
[ATTACH=full]7018[/ATTACH]Became this
(a makeshift cotterpin)
[ATTACH=full]7019[/ATTACH]Because of this
(my Vic)
[ATTACH=full]7020[/ATTACH]Which saved me yet another trip to the truck.
Used the Vic as a hammer again today. Nothing major, just some plastic anchors when installing a new Frost Proof Hose faucet.
(pic of me tappin =g in some plastic anchors)
[ATTACH=full]7078[/ATTACH]Also had to get the Vic's bit extension in the drill to allow the chuck to not rub the handle of the faucet. Its hard to screw the screws in if the driver head is at an angle. It'd just strip the screws and rub marks on the plastic handle. Yep, the Vic saved me 2 trips to the truck on that job.

[ATTACH=full]7079[/ATTACH]The awl helped remove the cartridge clip from a moen Tub & Shower valve. No better tool for that. I always goto the Vic Awl!

Used it to reconnect my CB radio after the repair shop replaced my battery cable and left it off.
This is a dramatic reenactment...

Also had to retract the hood's locking mechanism with the flathead. Have to do it every time I pop the hood:)

Hoping the pics show up. I'll edit if they don't.
EDIT: some did, some didn't. I labeled the ones that didn't though they were pretty self explanitory.
If you'd like to see my thread its here
-
I used the medium flathead on the Juice S2 to replace the battery in my car's fob. Then I used the same flathead (since it was already out) to scrape a decade's worth of crud out of the fob before reassembling.
At home, I have the Juice S2, an original PST, and a Vic Tinker on my living room table. When something arises, I grab whatever seems like the most likely needed tool, and go to it.
-
I used my Classic scissors to open some medicine packets and to cut some tags and zip ties.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login