Tofty's Custom Brass Torches
-
Cheers,
I'm going to use a Carclo TIR (total internal reflection) lens.
It isn't a conventional reflector but rather uses it's shape to internally reflect light until it's alligned with the desired direction of output in quite a tight beam.There nice and cheap and i wanted to try something a little different.
-
Forgive my ignorance but would the fact the reflector is plastic work OK on such a high output light? I've no idea what type of plastic it is of course :)
-
The lens is made from UV stabilised Polycarbonate with close to 90% light transmission efficiency. Polycarbonate starts to soften at 150 degrees celsius and start to melt at 300.
The same type of optic is used in the torchlabs triple LED P60 dropins (over 1000 lumens) with no reported lens meltings.The LED is mounted on a 10mm thickness of solid brass that flairs out to the fully finned surface of the head that will give better heat dissipation than most high energy torches iv'e seen.
The driver goes from low to medium to high so that if the maximum LED output is well above 200 lumens most jobs wouldn't require that much light so a lower setting could happily be used.
If i were to use a lower ampage driver the max output and therefore heat buildup would be much lower than that for which problems could possibly arise.The battery will be a single AW IMR 16340 which will run the light at full power for about 10 minutes max.
And the best thing is that the lenses cost $1.50 each so i can experiment wildly and burn out as many as i like without wasting too much money.
-
Toroughly explained... Thanks!

-
As i'm nearly finished building my Ti DIVE torch i set about ordering all the parts i need so i can start on the heat-sinked brass torch. I ended up ordering a selection of possible drivers and LED types to experiment with as well as some parts for other potential projects including some AAA drivers and XM-Ls on small boards.
I then set about designing something around the parts and this is what i came up with:



The body is made up of a copper head, brass body and nickel-silver tail with stainless ends and body rings. The colours in the render should be taken with a pinch of salt as nickel silver should have a slightly yellowish silver hue rather than a deep gray.
It has a clicky tail switch with metal button cover and an aspherical lens.
The driver runs at 500mA on a maximum of 1.5V so no rechargable lithiums. -
@Tofty said:
As i'm nearly finished building my Ti DIVE torch i set about ordering all the parts i need so i can start on the heat-sinked brass torch. I ended up ordering a selection of possible drivers and LED types to experiment with as well as some parts for other potential projects including some AAA drivers and XM-Ls on small boards.
I then set about designing something around the parts and this is what i came up with:



The body is made up of a copper head, brass body and nickel-silver tail with stainless ends and body rings. The colours in the render should be taken with a pinch of salt as nickel silver should have a slightly yellowish silver hue rather than a deep gray.
It has a clicky tail switch with metal button cover and an aspherical lens.
The driver runs at 500mA on a maximum of 1.5V so no rechargable lithiums.Wow! That is spectacular! If you ever decide to sell this one, let me know!
Seriously.

-
stunning mate.

-
It's been a while but here's another MXDL build.
Added i little more detail to the Mark III but it's pretty much the same.



and just for fun, HDR:

With only one long term project still in progress i can finally start making the finned brass torch prototype and then the copper/brass/nickel silver torch. I have all the materials needed for the first one so watch this space.
-
That thing's incredibly cool! Makes me want to start steampunk cosplaying. :D
One question though, what does that beast weigh?
-
Can't wait!!
-
It weighs approximately 55grams which isn't too bad considering my original brass torch must weigh twice that.
-
55g, or 0.64 Vic Harvesters, that's a lot less than I expected. Cool!
-
I like the way it tapers further down the body compared to most torches

-
I can't imagine how many hours went in to that Mate :o
Its just

-
Damn

-
Cheers Guys.
Anyone remember this:

well........



Getting there.
I've decided to make two heads for this torch:
The first will be as planned, using an XM-L driven at 3A.
The second will use a nichia 219 (same size as XP-G) driven at 1.4A
This is because the smaller die of the nichia suits the TIR lens much better so should give a better beam pattern.
Also the nichia has a very high CRI which i want to try out.
Just got to order more parts now. -
Where was that ^^^^^ Sat evening !!!!!
Great meeting you the other night mate.
Just so everyone knows, Toftys lights are better in real life that on screen, works of art.
-
Thanks Essexman
I hadn't even started it on saturday, made the first cuts on sunday.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login