Loose plier joints
-
How are your plier joints holding up on the tools you use on a regular basis? In my experience they get loose way too fast, and I'm not abusing my tools. After a few weeks of use, my wire cutters can't even cut a thin wire without "bending it", and the jaws get stuck with the wire between the cutters.
I've searched and found some tips about not doing tasks that includes "twisting motions" with the pliers, but with an EDC tool I want to be able to do so. The tools I've had this problem with are LM juices, a Kick, a PST and an old Wave.
Any advice regarding tool care/use is very appreciated :)
-
@Sjoqvist said:
How are your plier joints holding up on the tools you use on a regular basis? In my experience they get loose way too fast, and I'm not abusing my tools. After a few weeks of use, my wire cutters can't even cut a thin wire without "bending it", and the jaws get stuck with the wire between the cutters.I've searched and found some tips about not doing tasks that includes "twisting motions" with the pliers, but with an EDC tool I want to be able to do so. The tools I've had this problem with are LM juices, a Kick, a PST and an old Wave.
Any advice regarding tool care/use is very appreciated :)
Silly..
You're doing it wrong.
They're not supposed to be used.....Doh
You're supposed to place them gently on a shelf and....and..(sigh). admire them. (A bigger sigh).
-
My longest serving work tool is now my Spirit X, nearly 3 years old. The pliers get used most days, though not hard. They have held up fine.
-
My Gerber 800 is holding up fine. I do quite a bit of twisting with the pliers and they are still tight and true. I also do a fair amount of cutting, so the replaceable wire cutters are great. They also have three cutting edges that can be rotated before you have to replace them.
Sent from my Galaxy Nexus using Tapatalk 2
-
Does it have removable cutters? If so try putting a small shim or thin piece of paper behind it to tighten it up. I've had many sets of plier based tools. All loosen up some but all still work fine.
-
Paper ?
How about a piece of beer can... -
@tattoosteve99 said:
Does it have removable cutters? If so try putting a small shim or thin piece of paper behind it to tighten it up. I've had many sets of plier based tools. All loosen up some but all still work fine.At the moment I'm only using tools without removable cutters, but that is a great idea :D
Also, does anyone know if the earlier styles of LM PST pliers with "smaller" joint is much weaker than your "modern" LM pliers?
-
I have a few tools that I bought used that have loose plier pivots, but I don't think I've ever used a tool hard or long enough to loosen the plier pivot myself. I have read about the phenominon though and it occurs to me there had been some discussion here before about gently tapping the pivot point with a hammer to tighten it up. I don't recall the actual details though- perhaps someone else has tried it and can fill everyone in?
I wouldn't let it bother me too much- as far as I'm concerned it is what the tool is, and generally if I've worn it in, I've gotten used to it as it got looser.
Def
-
In the past I have tightened up a normal pair of $15 pliers by stamping a couple of 'dots' in the pivot with a center punch, I guess it should work on your tools
(I don't know how this would affect your warranty :-\ ) -
I've never thought of that before, I'm gonna try it on my beater LM Kick first, but it sounds like a good idea

I've always woundered how people can say "I've used this juice for 5 years every day" in their youtube vids, and the pliers look as tight as my NIB Blast pliers (where you can feel the "cutters" when you close the jaws :D :D)
If that was my juice it would not be able to cut anything after 5 years of use :P
-
As far as I know the pivot is just a normal rivet with the head ground off, so peening to tighten it up is what I'd try. Its a big steel rivet though so I don't know how much force it would take.
-
@Sjoqvist said:
I've never thought of that before, I'm gonna try it on my beater LM Kick first, but it sounds like a good idea
I've always woundered how people can say "I've used this juice for 5 years every day" in their youtube vids, and the pliers look as tight as my NIB Blast pliers (where you can feel the "cutters" when you close the jaws :D :D)
If that was my juice it would not be able to cut anything after 5 years of use :P
If you try the center punch trick make sure you are resting the tool on a flat surface (like an anvil, the top of a large vice or a large hammer) and make two light 'dots' first then try the plier action then make the dots bigger until the pliers feel right (or until they don't move at all
) -
Thanks for the advice guys :D My pliers work alot better now

-
It worked? :o :o :ahhh
;)
Do you have any pictures of how it looks now please

-
Yes, although it is not as tight as it once was, and I dont "feel" the cutters when i close the jaws, but it worked alot better than I thought it would :)
Here's a picture
-
I'm glad it worked
you can always make the dots a tiny bit bigger but risk making it immoveableThanks for the picture

-
You can also sharpen your cutters too. I know exactly what your talking about my surge is the same way. I use the surge's diamond file to touch up the cutters but it's a never ending battle. The only tool I have that hasn't done this is my ST300, I've abused that thing and the cutters will still cut fine braided wire perfectly.
Stay multi my friends
-
My oldest tool is my sideclip, ten years now, and it has been used hard. I bent the pliers from twisting it and bent them back myself. Then i had to file a side of the cutters that had a ding. They still cut paper, and stranded wire is no problem. The rest of my tools are a bit newer and the pliers have loosened up a bit but al still cut just fine.
Glad you found a fix for your issue though!!!

Sent from my myphone using Crapatalk
-
@Mercury said:
Then i had to file a side of the cutters that had a ding. They still cut paper, and stranded wire is no problem.Wow, there is no way I can cut paper with any of my MT pliers, (well, maybe the NIB ones ::))
Do you "force the jaws together" with your other hand to reduce the small distance between the cutters? Or does it work anyway?
I guess I could try to touch up the cutters, but I doubt it will work since the cutters look fine

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login