Loose plier joints
-
In the past I have tightened up a normal pair of $15 pliers by stamping a couple of 'dots' in the pivot with a center punch, I guess it should work on your tools
(I don't know how this would affect your warranty :-\ ) -
I've never thought of that before, I'm gonna try it on my beater LM Kick first, but it sounds like a good idea

I've always woundered how people can say "I've used this juice for 5 years every day" in their youtube vids, and the pliers look as tight as my NIB Blast pliers (where you can feel the "cutters" when you close the jaws :D :D)
If that was my juice it would not be able to cut anything after 5 years of use :P
-
As far as I know the pivot is just a normal rivet with the head ground off, so peening to tighten it up is what I'd try. Its a big steel rivet though so I don't know how much force it would take.
-
@Sjoqvist said:
I've never thought of that before, I'm gonna try it on my beater LM Kick first, but it sounds like a good idea
I've always woundered how people can say "I've used this juice for 5 years every day" in their youtube vids, and the pliers look as tight as my NIB Blast pliers (where you can feel the "cutters" when you close the jaws :D :D)
If that was my juice it would not be able to cut anything after 5 years of use :P
If you try the center punch trick make sure you are resting the tool on a flat surface (like an anvil, the top of a large vice or a large hammer) and make two light 'dots' first then try the plier action then make the dots bigger until the pliers feel right (or until they don't move at all
) -
Thanks for the advice guys :D My pliers work alot better now

-
It worked? :o :o :ahhh
;)
Do you have any pictures of how it looks now please

-
Yes, although it is not as tight as it once was, and I dont "feel" the cutters when i close the jaws, but it worked alot better than I thought it would :)
Here's a picture
-
I'm glad it worked
you can always make the dots a tiny bit bigger but risk making it immoveableThanks for the picture

-
You can also sharpen your cutters too. I know exactly what your talking about my surge is the same way. I use the surge's diamond file to touch up the cutters but it's a never ending battle. The only tool I have that hasn't done this is my ST300, I've abused that thing and the cutters will still cut fine braided wire perfectly.
Stay multi my friends
-
My oldest tool is my sideclip, ten years now, and it has been used hard. I bent the pliers from twisting it and bent them back myself. Then i had to file a side of the cutters that had a ding. They still cut paper, and stranded wire is no problem. The rest of my tools are a bit newer and the pliers have loosened up a bit but al still cut just fine.
Glad you found a fix for your issue though!!!

Sent from my myphone using Crapatalk
-
@Mercury said:
Then i had to file a side of the cutters that had a ding. They still cut paper, and stranded wire is no problem.Wow, there is no way I can cut paper with any of my MT pliers, (well, maybe the NIB ones ::))
Do you "force the jaws together" with your other hand to reduce the small distance between the cutters? Or does it work anyway?
I guess I could try to touch up the cutters, but I doubt it will work since the cutters look fine

-
I've always woundered how people can say "I've used this juice for 5 years every day" in their youtube vids, and the pliers look...
I'm thinking that usually means "I've carried this in my pocket for 5 years..."
Heh, I'm kinda guilty of that.
But really, I just use my pliers infrequently and my wire cutters almost never. When I do use the pliers it's usually on nuts, pipe fittings, the kind of thing that you grip sideways, or just for pulling or pushing, like with wiring harness connectors and stuff. I don't do a lot of wire cutting and I usually use a real wire cutter/stripper when I have to. My MTs get used mostly for cutting and screwdriving.
-
@Syph007 said:
As far as I know the pivot is just a normal rivet with the head ground off, so peening to tighten it up is what I'd try. Its a big steel rivet though so I don't know how much force it would take.How do you know what side of the pivot to tap?. My Leatherman Squirt PS4 scissors is a touch loose so they dont cut as nice as they should.
-
If you look at the inner circle and it moves when you move the handles that is the side to dot with the center punch

I have just looked at a skeletool, Super tool and Core to check this but I'm not sure about other tools

-
@sparky415 said:
If you look at the inner circle and it moves when you move the handles that is the side to dot with the center punch
I have just looked at a skeletool, Super tool and Core to check this but I'm not sure about other tools

Thanks. That is what I did on the pliers of the PS4, but I wasnt sure it would work the same way as the scissors.
I appreciate it.
-
Okay. Now Im stumped
.I just put a pen mark on both sides of the pivot, but they didnt move, so now I dont know which side to peen. Any other way to find out??.
-

It should look like this Mash

It looks like it would work on my Micra But I don't own a squirt :-\
Turn a bright light on :D -
It should look like this Mash

It looks like it would work on my Micra But I don't own a squirt :-\
Turn a bright light on :D
:D. I will give that a try with the bright light, but it will have to wait till I get home from work.Thanks man..

-
Good luck


I bought myself a magnifying glass at the last carboot sale I went to :-[
:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login