The spring for adding scissors to 93mm Alox?
-
That would save a lot of mucking about in general.
I'll keep all my bits crossed :D
-
Like I said, if those springs work you've got a customer. I'm planning on making a bunch of Farmer + Scissors for Christmas and birthday presents.
-
The 440C stainless just showed up this evening. 6 inches by 6 feet so we should have hundreds of them when all is said and done. It's measuring .150" thick so roughly a third of them will be slightly modified before heat treat and surface ground to .135" for use with the 91mm pliers and the rest at .110" for the scissors. Laser cutting, deburring and modding of the pliers springs, hole reaming, heat treat, surface grinding and finally tumble polishing. It's quite a process but it sure beats eating up an entire Pioneer for the blade spring.
-
Now that takes all the fun out of modding :p
-
Don't worry, I still have fun modding! :D The reasons I wanted to try this were two fold, one is to get a perfect scissor snap open/close and two, to not have to waste a pioneer just to get the blade spring for use with scissors. If you do that enough you end up with a bunch of parts that dont fit together to make anything good and it breaks the continuity of the process for me. Unless I wanted to make saks with an opener layer and nothing else... which I dont.
Also if you do enough plier mods that take 2x farmer saw layer springs, you end up with a pile of saw blades which I haven't figured out a good use for. So far I've been grinding one down to fit on an 84mm but thats about it.
I'd love to have custom springs for every part that could go on a 93, then its just a matter of picking the layers you want, liners, color, screw style.... :D
-
@Syph007 said:
Don't worry, I still have fun modding! :D The reasons I wanted to try this were two fold, one is to get a perfect scissor snap open/close and two, to not have to waste a pioneer just to get the blade spring for use with scissors. If you do that enough you end up with a bunch of parts that dont fit together to make anything good and it breaks the continuity of the process for me. Unless I wanted to make saks with an opener layer and nothing else... which I dont.Also if you do enough plier mods that take 2x farmer saw layer springs, you end up with a pile of saw blades which I haven't figured out a good use for. So far I've been grinding one down to fit on an 84mm but thats about it.
I'd love to have custom springs for every part that could go on a 93, then its just a matter of picking the layers you want, liners, color, screw style.... :D
You're just not trying hard enough :P :D
-
Ha! Yes maybe I'll be the first to make an 8 layer alox 93mm with 16 bottle opener layers! lol. Somehow I ended up with way more of those than any other part.
I saw the bottle opener mod before, but having seen the multi-saw one yet.

-
I seem to recall scibeer making an all bottle opener SAK years back as well. Mine was the beans and beer variant. A classic combination

-
@Syph007 said:
Blade spring from alox solo - Wastes a discontinued solo but looks awesome as the curve of the rest matches the knife profile and back looks flush, ends up looking like it was factory made that way. This works best with the older style scissors with fatter thumb pad.I have no qualms killing a solo, but what are these older style scissors you speak of?
-
Blade spring from alox solo - Wastes a discontinued solo but looks awesome as the curve of the rest matches the knife profile and back looks flush, ends up looking like it was factory made that way. This works best with the older style scissors with fatter thumb pad.
I have no qualms killing a solo, but what are these older style scissors you speak of?
The profile of the scissor part your thumb rests against changed over the years. The older style was fatter and had more metal to work with, while the modern style is thinner. There are at least 8 subtle variations in scissors over the years. Tom had pointed that out to me, I was only aware of 2. Having more metal there lets me dial in the fit with the solo spring so it has just the right tension and ramp to close proper.
-
Sorry if I am dense, but can the 91mm scissors fit the alox solo backspring as is? Does the backspring need modding? The scissors? In particular do late model scissors work? If so this would seem that Vic could make a factory 93mm alox with scissors with the tiny bit of work of drilling out the 91mm scissors to 3mm.
Hmmm
-
@Neil said:
I'm scared of grinding backsprings :ahhh :D so always use the older way with a 91mm spring but no back tool.
Works well but does look strange on the back. You can use a bushing on the middle pin, it will increase tension but personally I find the snap acceptable without.
A dedicated custom made backspring for the job would be cool 8)
How well will this work with a smooth back spring from a older model climber, etc?
-
@papercut said:
Sorry if I am dense, but can the 91mm scissors fit the alox solo backspring as is? Does the backspring need modding? The scissors? In particular do late model scissors work? If so this would seem that Vic could make a factory 93mm alox with scissors with the tiny bit of work of drilling out the 91mm scissors to 3mm.You will have to grind down the tip of spring a bit to make place for the scissors handle.
Also you won't get the full snap from the maximum angle because you can't grind off enough to allow this. The solo spring requires you to rest the scissors with the handle, not the blade tip. This bothered me so much that I introduced another modification to the spring: a custom rest

-
In the stickie harryf3 did this with the older smooth spring style. Check that out.
-
No longer stickied it seems, but I found it. How is the spring with such smooth back mod?
Cheers
-
Well it's shorter, so there is a gap.

</post/501900>
-
Well crap :(. Wonder what happened to the sticky? Mods check that please. I have the pics saved though :) I saved them all just in case it went missing :)
-
Found it! Apparently the mods removed from the sticky
lol./post/695993
Here ya go :) -
That one is the old style back spring from a 91mm no hook. You have to drill a new hole and grind the spring to fit. The snap is great once you reprofile it. If you want more snap you leave more material. However if you leave to much you risk bending the pins after time. Ask me how I know lol.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

