And so it begins.... (My adventures into Alox!)
-
NICE, so I see the one part works,, JR
The combo needed a very gentle bend to fit in with the other blade. It was rubbing a tiny bit without some krinking. The only issue though is the nail nick is on the wrong side, but there was no helping that.
. Now the question is, will it fit across from a Philips? JR
+1
Now that I'd like to see! -
Seriously ground-breaking work going on here. Exciting times to be a SAK enthusiast!

-
Syph, just a few things.
You said solo springs need little modification to accept scissors. What would than be? Grinding?
Also, are you using 91mm scissors for the Pioneers? -
@crackout said:
Syph, just a few things.You said solo springs need little modification to accept scissors. What would than be? Grinding?
Also, are you using 91mm scissors for the Pioneers?Yes 91mm scissors, and the solo springs just need a bit of the shoulder of the spring ground down. If not the scissors will catch and not close all the way. The amount you removed depends on the type of scissors. Older ones need more, newer style less. Its obvious when you assemble them you can see how it catches. I just grind a bit, then fit, and repeat until it sits right.
-
I see. Would old 91 non alox scissor springs also work?
-
Yes it will. There's a sticky thread from harryf3 that shows how to do that.
-
@crackout said:
I see. Would old 91 non alox scissor springs also work?Work yes, but its shorter so it doens't 'match' up with the other springs, or look very good IMO. But if you're only after function it works.
Edit: It was Harry who did this originally.
Farmer with scissors and no gap
So I offered to make a custom alox SAK for a good friend from UK because I needed to return a favor. His dream alox is a Farmer with added scissors. All the ...
Multitool.Org Forum (multitool.ninja)

-
Ha, okay. Now that's functional.

-
As a side note, saw springs work too ;)
-
Curious as to what the set of scales with the back tool cut out are to be used for. I missed that the first ten times I have read this(top left).

-
Mhhhhmmhmh... Backtool Alox.

-
@nj2656 said:
Curious as to what the set of scales with the back tool cut out are to be used for. I missed that the first ten times I have read this(top left).Ah you spotted those eh? I did the cutout before anodize so it would look stock and smooth. It's going to an 84mm alox golfer. Im going to do a hidden 4th pin so I can get backscales on. :D
-
In a trade with Aaron (bushido) some time ago I got a set of unfinished Ti scales. I just finally got up the nerve to start working on them to make a Ti urban pioneer. I had to come up with a jig to round and smooth the scale edges and then went through many many sheets of all the grits of sandpaper I had up to 1000 grit to get a nice shiny surface. So... about 3 hrs per scale just to surface finish. :D
Aaron is smurfing crazy to have cut these things out by hand with a jewelers saw and hand finish so many of them. NOW I see why it was such a big deal for him to be doing Ti on SAKs by hand.. its HARD and time consuming to finish Titanium!! Oh well, the one I got done so far looks very pretty and hopfully its partner will take less time.. then onto the liners! :D
Here are some pics of the finished one compared to the unfinished.



-
Oooh shiny!
Any progress on the bits for my little knife yet? :D
-
Any progress on the bits for my little knife yet? :D
Still waiting on springs. They're sitting as a low priority job at a machine shop waiting to get surfaced. :( Aaron keeps checking on them but they still arent done. Apparently they tried on one machine but that didn't work, so they are waiting their turn on the machine with the more powerful electromagnetic chuck.
-
Hey you missed a spot lol
jk. Those look 
-
Oooh shiny!
Any progress on the bits for my little knife yet? :D
Still waiting on springs. They're sitting as a low priority job at a machine shop waiting to get surfaced. :( Aaron keeps checking on them but they still arent done. Apparently they tried on one machine but that didn't work, so they are waiting their turn on the machine with the more powerful electromagnetic chuck.
And it was all going so well! ::)
-
Oooh shiny!
Any progress on the bits for my little knife yet? :D
Still waiting on springs. They're sitting as a low priority job at a machine shop waiting to get surfaced. :( Aaron keeps checking on them but they still arent done. Apparently they tried on one machine but that didn't work, so they are waiting their turn on the machine with the more powerful electromagnetic chuck.
And it was all going so well! ::)
I'm trying to be patient and work on other things in the mean time, but I'll be one happy modder to finally get the springs in hand and put them to work. :D
-
I was thinking about trying a pivot mod next as well.
However, since I'm from metric Germany (:P) I think I'll make some custom 3mm diameter pivots myself. How big is the hole in the Alox tools?You guys redrill to get 1/8 inch, which is around 3.17mm. If I make 3mm pivots, will they fit directly?
I know I would have to drill the 91mm tools, but what about the 93 ones?Oh, one more thing: If I get a Farmer and replace the saw for scissors (can't go with a Pioneer, because I need the liner), do I even need a solo spring or can the saw spring handle it as well?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login