Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Going about a mod

Scheduled Pinned Locked Moved The Mod Squad
13 Posts 1 Posters 6.1k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Going about a mod
Going about a mod
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Grant Lamontagne Offline
    Grant Lamontagne
    administrators
    Posts: 67,980
    Grant Lamontagne Offline
    Grant Lamontagne
    administrators
    wrote on last edited by
    #1 Quote Reply

      Well the Charge isn't necessarily the worst one to start with as one of our members (J-Sews) has disassembled and reassembled quite a few of them and can probably help you if you get lost at some point. Bear in mind that there are numerous little washers in there in addition to the implements themselves so it might appear impossible once you've got it open!

      As for the security bits, some folks have managed to find them in various places, including eBay and local hardware store. Some of them may chime in and tell you where to start looking.

      Def


      1 Reply Last reply
      • Leatherman123 Offline
        Leatherman123
        Posts: 6,568
        Leatherman123 Offline
        Leatherman123
        wrote on last edited by
        #2 Quote Reply

          Most hardware stores sell them. They usually have just one T6 security torx for five bucks or a whole kit for twenty bucks. The kit has many odd assorted bits that you don't readily see! Or you can just get two T6 security torx bits for ten and have exactly what you need! :think:

          1 Reply Last reply
          • scibeer Offline
            scibeer
            Posts: 427
            scibeer Offline
            scibeer
            wrote on last edited by
            #3 Quote Reply

              I'm still working up the courage to take a couple multis apart.

              I usually take a bunch of pictures before tearing something new apart. They come in really handy once you forget where everything was.

              Good luck and post some pix as you go if you get a chance.

              1 Reply Last reply
              • Leatherman123 Offline
                Leatherman123
                Posts: 6,568
                Leatherman123 Offline
                Leatherman123
                wrote on last edited by
                #4 Quote Reply

                  Scibeer, if your amazing at taking apart SAKs then I'm sure you can take apart a MT! :D

                  1 Reply Last reply
                  • J-sews Offline
                    J-sews
                    Admin Team
                    Posts: 23,224
                    J-sews Offline
                    J-sews
                    Admin Team
                    wrote on last edited by
                    #5 Quote Reply

                      First question is, how many points are there on the torx fasteners holding your Charge and your Wave together? Leatherman started off using 5-point security torx, and its not easy to obtain bits. A couple years ago they switched to 6-point security torx, bits for which are readily available. Which kind does yours have?

                      1 Reply Last reply
                      • E. Danny Offline
                        E. Danny
                        Posts: 180
                        E. Danny Offline
                        E. Danny
                        wrote on last edited by
                        #6 Quote Reply

                          My Charge and Wave both have 6 pointed bits, I made sure to check that out too!

                          1 Reply Last reply
                          • J-sews Offline
                            J-sews
                            Admin Team
                            Posts: 23,224
                            J-sews Offline
                            J-sews
                            Admin Team
                            wrote on last edited by
                            #7 Quote Reply

                              @E. Danny said:
                              My Charge and Wave both have 6 pointed bits, I made sure to check that out too!

                              Cool! I've seen the 6-point security bits all over, including the local hardware store. :)

                              Don't be too concerned about messing anything up. Follow Bill's advice and take pictures before beginning. There are indeed a lot of washers and parts but you are only dealing with one handle in each tool. (Is that right, you can do the swap you want by only disassembling one pivot point in each tool?)

                              1 Reply Last reply
                              • E. Danny Offline
                                E. Danny
                                Posts: 180
                                E. Danny Offline
                                E. Danny
                                wrote on last edited by
                                #8 Quote Reply

                                  ya, i only gotta disassemble the one handle on both tools. just a real simple mod of switching tools out.

                                  1 Reply Last reply
                                  • J-sews Offline
                                    J-sews
                                    Admin Team
                                    Posts: 23,224
                                    J-sews Offline
                                    J-sews
                                    Admin Team
                                    wrote on last edited by
                                    #9 Quote Reply

                                      You should have no problems then. For reference, here's a Charge ALX totally disassembled (picture posted previously).

                                      Only thing to be careful of is sorta hard to explain. The pivot screw you will be removing is actually two pieces, obviously. One side is a screw, the other side is a hollow threaded post. The post has flats on it that engage flats on the handle frame and the little washers, preventing tool "clumping".

                                      Using your security torx bits, you want to hold the "post" side stationary while rotating only the "screw" side.

                                      (Does that make any sense?) :P

                                      1 Reply Last reply
                                      • scibeer Offline
                                        scibeer
                                        Posts: 427
                                        scibeer Offline
                                        scibeer
                                        wrote on last edited by scibeer
                                        #10 Quote Reply

                                          So my charge has the round screws with the ridges on the outside like a quarter. I know the wrench for it must be hard to get a hold of.

                                          So, dremel some slots and use a flat screwdriver, or make a quicksteel mold?? Channel locks will just make it ugly I'm sure.

                                          I don't even want to change anything really, just rip the sucker apart!

                                          These metal inserts on the handles have to go to. I have the slvr version from Costco.

                                          1 Reply Last reply
                                          • Grant Lamontagne Offline
                                            Grant Lamontagne
                                            administrators
                                            Posts: 67,980
                                            Grant Lamontagne Offline
                                            Grant Lamontagne
                                            administrators
                                            wrote on last edited by
                                            #11 Quote Reply

                                              Try ordering a couple of Kick pocket clips- they work as wrenches to loosen the knurled LM screws.

                                              Def


                                              1 Reply Last reply
                                              • J-sews Offline
                                                J-sews
                                                Admin Team
                                                Posts: 23,224
                                                J-sews Offline
                                                J-sews
                                                Admin Team
                                                wrote on last edited by
                                                #12 Quote Reply

                                                  @Defender said:
                                                  Try ordering a couple of Kick pocket clips- they work as wrenches to loosen the knurled LM screws.

                                                  Def

                                                  The clips work great, but only on the blade pivot screws. The plier pivot screws are a bigger size and don't fit. :(

                                                  clip wrench 1.jpg

                                                  clip wrench 2.jpg

                                                  1 Reply Last reply

                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                  With your input, this post could be even better 💗

                                                  Register Login

                                                  1. Home
                                                  2. Tool Talk
                                                  3. The Mod Squad
                                                  4. Going about a mod
                                                  Reply
                                                  • Reply as topic
                                                  Log in to reply
                                                  COMMUNITY LINKS
                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                  Operational Funds

                                                  Help us keep the Unworkable working!

                                                  Make A Donation
                                                  November Goal: $300.00
                                                  Due Date: Nov 30
                                                  Total Receipts: $0.00
                                                  Below Goal: $300.00
                                                  0% funded
                                                  • Login

                                                  • Don't have an account? Register

                                                  • Login or register to search.
                                                  • First post
                                                    Last post
                                                  0