ST 300 owners club
-
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness

-
@J-sews said:
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness
Yeah i was using the core and and buck extract pliers, but there is very little meat to get a grip on, so I went with a standard needlenose and regular plier tools, was able to spin it a little, seems a little better might try it once more, but I'm getting some scratches around the screw :P. Maybe some vice grips would work better? Would be nice if they just used a stinkin hex screw
-
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness

Yeah i was using the core and and buck extract pliers, but there is very little meat to get a grip on, so I went with a standard needlenose and regular plier tools, was able to spin it a little, seems a little better might try it once more, but I'm getting some scratches around the screw :P. Maybe some vice grips would work better? Would be nice if they just used a stinkin hex screw
Amen to that!

-
You could grip both knurled screw heads with a couple of good pliers and try snugging them up a bit. It shouldn't take much; a quarter turn at most should take care of the looseness

Yeah i was using the core and and buck extract pliers, but there is very little meat to get a grip on, so I went with a standard needlenose and regular plier tools, was able to spin it a little, seems a little better might try it once more, but I'm getting some scratches around the screw :P. Maybe some vice grips would work better? Would be nice if they just used a stinkin hex screw
Amen to that!

The Needle nose vice grip works great for this application + a little oil and its working perfectly now, I just wish their quality control wasn't so hit or miss.
-
Another odd thing I noticed about ST300 Vs. the Core(they are almost identical) is the ST300 side with 2 flatheads and awl - the thumb studs are all even, but on the Core they vary in length and are easier to get out, seems like a poor design downgrade imo.
-
@Blackbeard said:
Another odd thing I noticed about ST300 Vs. the Core(they are almost identical) is the ST300 side with 2 flatheads and awl - the thumb studs are all even, but on the Core they vary in length and are easier to get out, seems like a poor design downgrade imo.That has to do with the ST300 tool clumping feature. On the Core the tools could come out individually, so the staggered nail nicks were standard, a feature not necessary on the ST300.
One note though, the last run of Core's and any that have been factory refurbished lately will have the ST300 implements. Not a big deal, but it does defeat the "one tool at a time" feature.
-
Another odd thing I noticed about ST300 Vs. the Core(they are almost identical) is the ST300 side with 2 flatheads and awl - the thumb studs are all even, but on the Core they vary in length and are easier to get out, seems like a poor design downgrade imo.
That has to do with the ST300 tool clumping feature. On the Core the tools could come out individually, so the staggered nail nicks were standard, a feature not necessary on the ST300.
One note though, the last run of Core's and any that have been factory refurbished lately will have the ST300 implements. Not a big deal, but it does defeat the "one tool at a time" feature.
I kinda disagree, the offset nailnicks would still make it easier to chose the tool u want and put the others away faster even witht he clumping, I think they dropped the ball on this aspect, but overall I'm pretty happy with the tool especially since it cost $37 >:D
-
@Blackbeard said:
I kinda disagree, the offset nailnicks would still make it easier to chose the tool u want and put the others away faster even witht he clumping,Good point, but the redesign of the ST300 was done with the goal of having all of the tools come out at once, and then being able to flick through them with your thumb. Having the nicks all in line does give a nice wide area to grab the tools.
-
I kinda disagree, the offset nailnicks would still make it easier to chose the tool u want and put the others away faster even witht he clumping,
Good point, but the redesign of the ST300 was done with the goal of having all of the tools come out at once, and then being able to flick through them with your thumb. Having the nicks all in line does give a nice wide area to grab the tools.
Well I also don't agree with Joe Leatherman there...If you have both tools, do a side by side test, you can deploy the core tools 5x faster and easier than the supertool, so I say leave the clumping to SOG. maybe they designed it for ogres or the giants in the nba or better yet to save $.
-
Perhaps a bit of thread necromancy is in order? I felt asking this question fit better here than a new thread. My ST300's pivot has the distinct problem of being functionally loose, until I squeeze the handles really tight, then the head is tight to the point the handles almost want to close, until I open it and close it fully a couple times, and it returns to normal. Any ideas?
-
Is this a new problem or was it that way since you got it? Maybe the screw isn't sitting right?
In any case, I just wanted to use this smiley. :D

-
Hey, I'm in this one now too! Got a BO ST300 in a trade a few weeks ago!

-
Well i finally bought one yesterday. Its on its way, cant wait for it to get here. I have no idea what version it is but the seller said '2012' model. Its been over a year that i since decided i wanted one and liked what i saw then so i have no idea if theres been any updates. Hopefully its still made in USA (fingers crossed)
-
@Cyclone82 said:
Well i finally bought one yesterday. Its on its way, cant wait for it to get here. I have no idea what version it is but the seller said '2012' model. Its been over a year that i since decided i wanted one and liked what i saw then so i have no idea if theres been any updates. **Hopefully its still made in USA ** (fingers crossed)It is my main hard use multitool. I only wish it had a diamond file on it.. As far as I know the 2012 model is still the same.
They are made in the US but as some parts may be made oustide the US legally LM is not allowed to put USA on them.
-
Got mine today. My first full size Leatherman.
-
@Cyclone82 said:
Got mine today. My first full size Leatherman.Haven't seen that user name in a long time. Welcome back. How's your GAK collection, growing? I hope you enjoy the st300.
-
Looks like I'm in the club Had my ST for a long time now. It was a replacement for my ST200. Its my #1 leatherman :) Does anyone else ST300 open balisong style?
-
Haven't seen that user name in a long time. Welcome back. How's your GAK collection, growing? I hope you enjoy the st300.
Yeah i am still here. Have not bought any GAK's for 12months or more. Its just a never ending addiction that i had to ease up on.
The ST300 seems pretty good. I probably would not bother with any other smaller ones at this stage apart from the squirt, juice and Minis which i have an like.
Cant really pick any faults with the 300. Yeah the handles flex when squeezing hard but i thought that was normal. Plier tips line up 99% perfect. I like the look of theplier head on this one. Would have been nice to have USA or Portland OR on the handles like the old LM's. Just says Leatherman tool so you never actually really know where they are made.
I spoke too soon .One thing I did notice on the 300, on ethe edge of the file, is that ment to be a metal saw? The teeth on mine are pretty poor, uneven and to be honest it looks like they are worn down already? No where near anything like the teeth on my KF4’s. This should not have got past QC surely?
Edit - i looked at the website and it does not mention a 'metal saw' so i guess i am ok then?
-
One thing I did notice on the 300, on the edge of the file, is that ment to be a metal saw? The teeth on mine are pretty poor, uneven and to be honest it looks like they are worn down already? No where near anything like the teeth on my KF4’s. This should not have got past QC surely?
Edit - i looked at the website and it does not mention a 'metal saw' so i guess i am ok then?
Anyone have an answer for this? I need to know if i need to return or exhange mine with the seller?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login