Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

84/91mm Combo Tool in Mods

Scheduled Pinned Locked Moved Swiss Army Knights Forum
34 Posts 1 Posters 7.3k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. 84/91mm Combo Tool in Mods
84/91mm Combo Tool in Mods
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • PTRSAK Offline
    PTRSAK
    Posts: 4,776
    PTRSAK Offline
    PTRSAK
    wrote on last edited by
    #7 Quote Reply

      You can use cobalt drills, BUT you have to do it right... Low speed, (relatively) High feed and coolant/lubricant.
      You have to use a sharp drill and keep it cutting. If you don't lean on it enough it will burnish the cutting edge off and you bow have a blunt cobalt drill that is a bitch to sharpen because of the thick web.
      If you lean on it too hard.... PING. You have a broken drill.

      With the number of cobalt drills you are likely to go through it's probably cheaper to buy carbide if you plan to do this even on a slightly regular basis.

      I tend to use a carbide bit in my dremel and then finish the hole with a round diamond needle file.

      1 Reply Last reply
      • WiSAKfan Offline
        WiSAKfan
        Posts: 460
        WiSAKfan Offline
        WiSAKfan
        wrote on last edited by
        #8 Quote Reply

          i remember now i had to improvise with a cobalt bit that was smaller then the hole and had to widen the hole out with that

          took a while

          but hey got er done

          1 Reply Last reply
          • Syph007 Offline
            Syph007
            Global Moderators
            Posts: 9,842
            Syph007 Offline
            Syph007
            Global Moderators
            wrote on last edited by
            #9 Quote Reply

              Lately Ive been getting super cheap carbide bits from this place. They dont last as long but are about 1/4 the cost so overall they work good enough. I can get 30 holes from one bit if im careful.

              http://drillbitsunlimited.com/New-Drill-Bits-C291007.aspx?sid=25472

              Shipping to canada was cheap, might be worth checking what shipping to your country is.

              1 Reply Last reply
              • WoodMan Offline
                WoodMan
                Posts: 181
                WoodMan Offline
                WoodMan
                wrote on last edited by
                #10 Quote Reply

                  @PTRSAK said:
                  You can use cobalt drills, BUT you have to do it right... Low speed, (relatively) High feed and coolant/lubricant.
                  You have to use a sharp drill and keep it cutting. If you don't lean on it enough it will burnish the cutting edge off and you bow have a blunt cobalt drill that is a bitch to sharpen because of the thick web.
                  If you lean on it too hard.... PING. You have a broken drill.

                  With the number of cobalt drills you are likely to go through it's probably cheaper to buy carbide if you plan to do this even on a slightly regular basis.

                  I tend to use a carbide bit in my dremel and then finish the hole with a round diamond needle file.

                  When you say low speed, what ballpark RPMs are you talking about. I was planning to use about 1200 rpm.

                  And what type of carbide dremel bit. I'm guessing this is not a Dremel brand bit.

                  1 Reply Last reply
                  • WiSAKfan Offline
                    WiSAKfan
                    Posts: 460
                    WiSAKfan Offline
                    WiSAKfan
                    wrote on last edited by
                    #11 Quote Reply

                      the one i have is a dremel brand carbide

                      looks like this, it's not for drilling but you are grinding the sides

                      1 Reply Last reply
                      • WoodMan Offline
                        WoodMan
                        Posts: 181
                        WoodMan Offline
                        WoodMan
                        wrote on last edited by
                        #12 Quote Reply

                          @Syph007 said:
                          Lately Ive been getting super cheap carbide bits from this place. They dont last as long but are about 1/4 the cost so overall they work good enough. I can get 30 holes from one bit if im careful.

                          http://drillbitsunlimited.com/New-Drill-Bits-C291007.aspx?sid=25472

                          Shipping to canada was cheap, might be worth checking what shipping to your country is.

                          Forgive me if I'm missing something at the drillbitsunlimited.com site, but the closest bit I see is .096"/2.45mm. That's about .0025" under the stated 2.5mm brass rod. If that size works, I'm all for it because those bits are relatively cheap.

                          These are the ones I was looking at:
                          http://www.use-enco.com/CGI/INPDFF?PMPAGE=44&PARTPG=INLMK32

                          1 Reply Last reply
                          • Syph007 Offline
                            Syph007
                            Global Moderators
                            Posts: 9,842
                            Syph007 Offline
                            Syph007
                            Global Moderators
                            wrote on last edited by Syph007
                            #13 Quote Reply

                              @WoodMan said:

                              @Syph007 said:

                              Lately Ive been getting super cheap carbide bits from this place. They dont last as long but are about 1/4 the cost so overall they work good enough. I can get 30 holes from one bit if im careful.

                              http://drillbitsunlimited.com/New-Drill-Bits-C291007.aspx?sid=25472

                              Shipping to canada was cheap, might be worth checking what shipping to your country is.

                              Forgive me if I'm missing something at the drillbitsunlimited.com site, but the closest bit I see is .096"/2.45mm. That's about .0025" under the stated 2.5mm brass rod. If that size works, I'm all for it because those bits are relatively cheap.

                              These are the ones I was looking at:
                              http://www.use-enco.com/CGI/INPDFF?PMPAGE=44&PARTPG=INLMK32

                              I buy 0.125 size, but they do have 2.50 mm

                              http://drillbitsunlimited.com/098-250mm-NEW-Solid-Carbide-Drill-Bit--P2388152.aspx

                              They arent the highest quality, but they work. I get more holes from a 14 dollar spade bit, but if I figure it out as cost per hole drilled I think these are slightly better. Much better if you only need to drill a few holes.

                              1 Reply Last reply
                              • WoodMan Offline
                                WoodMan
                                Posts: 181
                                WoodMan Offline
                                WoodMan
                                wrote on last edited by
                                #14 Quote Reply

                                  @WiSAKfan said:
                                  the one i have is a dremel brand carbide

                                  looks like this, it's not for drilling but you are grinding the sides

                                  Found it, thanks:
                                  http://www.dremel.com/en-us/Accessories/Pages/ProductDetail.aspx?pid=9910

                                  1 Reply Last reply
                                  • WoodMan Offline
                                    WoodMan
                                    Posts: 181
                                    WoodMan Offline
                                    WoodMan
                                    wrote on last edited by
                                    #15 Quote Reply

                                      @Syph007 said:

                                      @WoodMan said:

                                      @Syph007 said:

                                      Lately Ive been getting super cheap carbide bits from this place. They dont last as long but are about 1/4 the cost so overall they work good enough. I can get 30 holes from one bit if im careful.

                                      http://drillbitsunlimited.com/New-Drill-Bits-C291007.aspx?sid=25472

                                      Shipping to canada was cheap, might be worth checking what shipping to your country is.

                                      Forgive me if I'm missing something at the drillbitsunlimited.com site, but the closest bit I see is .096"/2.45mm. That's about .0025" under the stated 2.5mm brass rod. If that size works, I'm all for it because those bits are relatively cheap.

                                      These are the ones I was looking at:
                                      http://www.use-enco.com/CGI/INPDFF?PMPAGE=44&PARTPG=INLMK32

                                      I buy 0.125 size, but they do have 2.50 mm

                                      http://drillbitsunlimited.com/098-250mm-NEW-Solid-Carbide-Drill-Bit--P2388152.aspx

                                      They arent the highest quality, but they work. I get more holes from a 14 dollar spade bit, but if I figure it out as cost per hole drilled I think these are slightly better. Much better if you only need to drill a few holes.

                                      Isn't .125" way too big? I would think a bit that much oversized would result in a lot of play in the tool.

                                      On a related note, what speed do you run the drill press at with the carbide bit?

                                      1 Reply Last reply
                                      • Syph007 Offline
                                        Syph007
                                        Global Moderators
                                        Posts: 9,842
                                        Syph007 Offline
                                        Syph007
                                        Global Moderators
                                        wrote on last edited by
                                        #16 Quote Reply

                                          @WoodMan said:

                                          @Syph007 said:

                                          @WoodMan said:

                                          @Syph007 said:

                                          Lately Ive been getting super cheap carbide bits from this place. They dont last as long but are about 1/4 the cost so overall they work good enough. I can get 30 holes from one bit if im careful.

                                          http://drillbitsunlimited.com/New-Drill-Bits-C291007.aspx?sid=25472

                                          Shipping to canada was cheap, might be worth checking what shipping to your country is.

                                          Forgive me if I'm missing something at the drillbitsunlimited.com site, but the closest bit I see is .096"/2.45mm. That's about .0025" under the stated 2.5mm brass rod. If that size works, I'm all for it because those bits are relatively cheap.

                                          These are the ones I was looking at:
                                          http://www.use-enco.com/CGI/INPDFF?PMPAGE=44&PARTPG=INLMK32

                                          I buy 0.125 size, but they do have 2.50 mm

                                          http://drillbitsunlimited.com/098-250mm-NEW-Solid-Carbide-Drill-Bit--P2388152.aspx

                                          They arent the highest quality, but they work. I get more holes from a 14 dollar spade bit, but if I figure it out as cost per hole drilled I think these are slightly better. Much better if you only need to drill a few holes.

                                          Isn't .125" way too big? I would think a bit that much oversized would result in a lot of play in the tool.

                                          On a related note, what speed do you run the drill press at with the carbide bit?

                                          I use 1/8 pivots so I drill out everything to 0.125.

                                          On my drill press I have the belt on the middle of the pulley stack, sorry I dont know what speed that is.

                                          1 Reply Last reply
                                          • WiSAKfan Offline
                                            WiSAKfan
                                            Posts: 460
                                            WiSAKfan Offline
                                            WiSAKfan
                                            wrote on last edited by
                                            #17 Quote Reply

                                              i use 3/32 which is common here in the states.

                                              the pivots syph007 uses are larger then the pin stock.

                                              1 Reply Last reply
                                              • WoodMan Offline
                                                WoodMan
                                                Posts: 181
                                                WoodMan Offline
                                                WoodMan
                                                wrote on last edited by
                                                #18 Quote Reply

                                                  @WiSAKfan said:
                                                  i use 3/32 which is common here in the states.

                                                  the pivots syph007 uses are larger then the pin stock.

                                                  Ah, because he's modding alox, not cellidor, knives?

                                                  1 Reply Last reply
                                                  • WiSAKfan Offline
                                                    WiSAKfan
                                                    Posts: 460
                                                    WiSAKfan Offline
                                                    WiSAKfan
                                                    wrote on last edited by WiSAKfan
                                                    #19 Quote Reply

                                                      he's using pivots instead of pins. it's not really anything to do with alox or cellidor, i may be wrong but i think one could use pivots for either EDIT provided you can drill out backside tools enough to use a pivot there

                                                      just a quick pic i found of his to show:

                                                      1 Reply Last reply
                                                      • enki_ck Offline
                                                        enki_ck
                                                        Global Moderators
                                                        Posts: 20,936
                                                        enki_ck Offline
                                                        enki_ck
                                                        Global Moderators
                                                        wrote on last edited by
                                                        #20 Quote Reply

                                                          @Syph007 said:

                                                          @WoodMan said:

                                                          @Syph007 said:

                                                          Lately Ive been getting super cheap carbide bits from this place. They dont last as long but are about 1/4 the cost so overall they work good enough. I can get 30 holes from one bit if im careful.

                                                          http://drillbitsunlimited.com/New-Drill-Bits-C291007.aspx?sid=25472

                                                          Shipping to canada was cheap, might be worth checking what shipping to your country is.

                                                          Forgive me if I'm missing something at the drillbitsunlimited.com site, but the closest bit I see is .096"/2.45mm. That's about .0025" under the stated 2.5mm brass rod. If that size works, I'm all for it because those bits are relatively cheap.

                                                          These are the ones I was looking at:
                                                          http://www.use-enco.com/CGI/INPDFF?PMPAGE=44&PARTPG=INLMK32

                                                          I buy 0.125 size, but they do have 2.50 mm

                                                          http://drillbitsunlimited.com/098-250mm-NEW-Solid-Carbide-Drill-Bit--P2388152.aspx

                                                          They arent the highest quality, but they work. I get more holes from a 14 dollar spade bit, but if I figure it out as cost per hole drilled I think these are slightly better. Much better if you only need to drill a few holes.

                                                          Thanks for that link. :salute: Bookmarked.

                                                          1 Reply Last reply
                                                          • WoodMan Offline
                                                            WoodMan
                                                            Posts: 181
                                                            WoodMan Offline
                                                            WoodMan
                                                            wrote on last edited by
                                                            #21 Quote Reply

                                                              @WiSAKfan said:
                                                              he's using pivots instead of pins. it's not really anything to do with alox or cellidor, i may be wrong but i think one could use pivots for either EDIT provided you can drill out backside tools enough to use a pivot there

                                                              Wouldn't there be a problem with the pivot screws bearing on the cellidor instead of alox?

                                                              I'm interested in this idea. Can someone who has modded a cellidor knife with pivots instead of brass rods post on this concept?

                                                              1 Reply Last reply
                                                              • WiSAKfan Offline
                                                                WiSAKfan
                                                                Posts: 460
                                                                WiSAKfan Offline
                                                                WiSAKfan
                                                                wrote on last edited by
                                                                #22 Quote Reply

                                                                  Link Preview Image
                                                                  Using torx pins for a mod.

                                                                  Hi guys. I've seen that Bushidomosquito has used some torx head pins for his custom SAK creations. I'm interested in trying to do a simple mod myself, putt...

                                                                  favicon

                                                                  Multitool.Org Forum (multitool.ninja)

                                                                  i found this thread with Syph007 says to just go with peening with cellidor since it's covered up anyways. a lot more work to drill everything out.

                                                                  good luck

                                                                  1 Reply Last reply
                                                                  • tattoosteve99 Offline
                                                                    tattoosteve99
                                                                    Posts: 6,326
                                                                    tattoosteve99 Offline
                                                                    tattoosteve99
                                                                    wrote on last edited by
                                                                    #23 Quote Reply

                                                                      If you have a drill press use either 2 flute or 4 flute carbide end mills. I use 2.5 and 3.0mm sizes. They can be bought on evilbay for about $7. I have 6 and only broke one so far( my fault). Get carbide with titanium nitride coating, that's what's recommended for hardened stainless steel.

                                                                      1 Reply Last reply
                                                                      • PTRSAK Offline
                                                                        PTRSAK
                                                                        Posts: 4,776
                                                                        PTRSAK Offline
                                                                        PTRSAK
                                                                        wrote on last edited by
                                                                        #24 Quote Reply

                                                                          @WoodMan said:
                                                                          When you say low speed, what ballpark RPMs are you talking about. I was planning to use about 1200 rpm.

                                                                          And what type of carbide dremel bit. I'm guessing this is not a Dremel brand bit.

                                                                          the chart I'm looking at says 50sf/m so... (for example) 1/8 drill = approx 0.4 inch circumference or 30 revs per foot. 30 x 50 = 1500rpm.

                                                                          No idea what brand my carbide bits are, I was "gifted" them when I did a home job for the tool storeman at a previous employer. :whistle:
                                                                          They are 1/8" and I have Ball, Straight (round end), Straight (square end) and Tapered, with 3 or 4 of each.

                                                                          1 Reply Last reply
                                                                          • WoodMan Offline
                                                                            WoodMan
                                                                            Posts: 181
                                                                            WoodMan Offline
                                                                            WoodMan
                                                                            wrote on last edited by
                                                                            #25 Quote Reply

                                                                              Thanks for all the advice.

                                                                              Ordered a 2.5mm end mill off ebay and the 2.5mm solid carbide drill bits that Syph007 recommended.

                                                                              1 Reply Last reply
                                                                              • Syph007 Offline
                                                                                Syph007
                                                                                Global Moderators
                                                                                Posts: 9,842
                                                                                Syph007 Offline
                                                                                Syph007
                                                                                Global Moderators
                                                                                wrote on last edited by
                                                                                #26 Quote Reply

                                                                                  Those cheap bits are fine for a couple dozen holes at least. I find end mills to be pretty bad drill bits when used in a drill press, but they would be fine in a mill. A drill is a poor mans mill, and if you dont use a drill bit the hole wont self center. Might not be noticable, but in things that I do like drilling out scales and springs a milling bit would be bad, its important to have the hole exactly on center and a drill bit will do that on its own.

                                                                                  Oh and cutting oil is a must. :D

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Swiss Army Knights Forum
                                                                                  4. 84/91mm Combo Tool in Mods
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0