Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

84/91mm Combo Tool in Mods

Scheduled Pinned Locked Moved Swiss Army Knights Forum
34 Posts 1 Posters 7.3k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. 84/91mm Combo Tool in Mods
84/91mm Combo Tool in Mods
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • tattoosteve99 Offline
    tattoosteve99
    Posts: 6,326
    tattoosteve99 Offline
    tattoosteve99
    wrote on last edited by
    #23 Quote Reply

      If you have a drill press use either 2 flute or 4 flute carbide end mills. I use 2.5 and 3.0mm sizes. They can be bought on evilbay for about $7. I have 6 and only broke one so far( my fault). Get carbide with titanium nitride coating, that's what's recommended for hardened stainless steel.

      1 Reply Last reply
      • PTRSAK Offline
        PTRSAK
        Posts: 4,776
        PTRSAK Offline
        PTRSAK
        wrote on last edited by
        #24 Quote Reply

          @WoodMan said:
          When you say low speed, what ballpark RPMs are you talking about. I was planning to use about 1200 rpm.

          And what type of carbide dremel bit. I'm guessing this is not a Dremel brand bit.

          the chart I'm looking at says 50sf/m so... (for example) 1/8 drill = approx 0.4 inch circumference or 30 revs per foot. 30 x 50 = 1500rpm.

          No idea what brand my carbide bits are, I was "gifted" them when I did a home job for the tool storeman at a previous employer. :whistle:
          They are 1/8" and I have Ball, Straight (round end), Straight (square end) and Tapered, with 3 or 4 of each.

          1 Reply Last reply
          • WoodMan Offline
            WoodMan
            Posts: 181
            WoodMan Offline
            WoodMan
            wrote on last edited by
            #25 Quote Reply

              Thanks for all the advice.

              Ordered a 2.5mm end mill off ebay and the 2.5mm solid carbide drill bits that Syph007 recommended.

              1 Reply Last reply
              • Syph007 Offline
                Syph007
                Global Moderators
                Posts: 9,842
                Syph007 Offline
                Syph007
                Global Moderators
                wrote on last edited by
                #26 Quote Reply

                  Those cheap bits are fine for a couple dozen holes at least. I find end mills to be pretty bad drill bits when used in a drill press, but they would be fine in a mill. A drill is a poor mans mill, and if you dont use a drill bit the hole wont self center. Might not be noticable, but in things that I do like drilling out scales and springs a milling bit would be bad, its important to have the hole exactly on center and a drill bit will do that on its own.

                  Oh and cutting oil is a must. :D

                  1 Reply Last reply
                  • WoodMan Offline
                    WoodMan
                    Posts: 181
                    WoodMan Offline
                    WoodMan
                    wrote on last edited by
                    #27 Quote Reply

                      @Syph007 said:
                      Those cheap bits are fine for a couple dozen holes at least. I find end mills to be pretty bad drill bits when used in a drill press, but they would be fine in a mill. A drill is a poor mans mill, and if you dont use a drill bit the hole wont self center. Might not be noticable, but in things that I do like drilling out scales and springs a milling bit would be bad, its important to have the hole exactly on center and a drill bit will do that on its own.

                      Oh and cutting oil is a must. :D

                      I was planning to first chuck up a regular 2.2mm (that is the hole size on an 84mm combo tool, isn't it?) drill bit and use that to accurately locate/clamp-up the part. Then remove the regular drill bit, install the larger 2.5mm bit or end mill, and drill. Hopefully, that technique will get me exactly on center.

                      In any case, I'm going to try the bits you recommended, first.

                      1 Reply Last reply
                      • Syph007 Offline
                        Syph007
                        Global Moderators
                        Posts: 9,842
                        Syph007 Offline
                        Syph007
                        Global Moderators
                        wrote on last edited by
                        #28 Quote Reply

                          You'll need to polish the inside of the hole, and its tiny. I just tightly roll up a small piece of sandpaper and use it in a cordless drill to sand. It seems an odd solution, but it really works well.

                          1 Reply Last reply
                          • Mike 56 Offline
                            Mike 56
                            Posts: 1,705
                            Mike 56 Offline
                            Mike 56
                            wrote on last edited by
                            #29 Quote Reply

                              I have drilled quite a few 84mm combo tools. I use cheap 7/32 drill bits i buy at Walmart. Heat is the enemy i run my drill press as slow i can. When the bit gets starts to get hot i let it cool some drilling more. It is slow but it works. I tried using oil while drilling but then my bits did not cut very well. Using charcoal lighter fluid worked pretty good it helped keep the bit cool and it still cut well. Just go slow.

                              1 Reply Last reply
                              • WoodMan Offline
                                WoodMan
                                Posts: 181
                                WoodMan Offline
                                WoodMan
                                wrote on last edited by
                                #30 Quote Reply

                                  @Mike 56 said:
                                  I have drilled quite a few 84mm combo tools. I use cheap 7/32 drill bits i buy at Walmart. Heat is the enemy i run my drill press as slow i can. When the bit gets starts to get hot i let it cool some drilling more. It is slow but it works. I tried using oil while drilling but then my bits did not cut very well. Using charcoal lighter fluid worked pretty good it helped keep the bit cool and it still cut well. Just go slow.

                                  Do you mean 7/64"? 7/32" would be far too big.

                                  1 Reply Last reply
                                  • Mike 56 Offline
                                    Mike 56
                                    Posts: 1,705
                                    Mike 56 Offline
                                    Mike 56
                                    wrote on last edited by
                                    #31 Quote Reply

                                      Yes you are right it is 7/64. 7/64 bits a little bigger than a 2.5 but they work fine. 7/64 bits are easier to come by here in the US.
                                      Mike

                                      1 Reply Last reply
                                      • WoodMan Offline
                                        WoodMan
                                        Posts: 181
                                        WoodMan Offline
                                        WoodMan
                                        wrote on last edited by
                                        #32 Quote Reply

                                          @Mike 56 said:
                                          I have drilled quite a few 84mm combo tools. I use cheap 7/32 drill bits i buy at Walmart. Heat is the enemy i run my drill press as slow i can. When the bit gets starts to get hot i let it cool some drilling more. It is slow but it works. I tried using oil while drilling but then my bits did not cut very well. Using charcoal lighter fluid worked pretty good it helped keep the bit cool and it still cut well. Just go slow.

                                          When you say "go slow" do you mean to use a slow rotational speed on the drill, or use a slow feed, or both?

                                          1 Reply Last reply
                                          • Mike 56 Offline
                                            Mike 56
                                            Posts: 1,705
                                            Mike 56 Offline
                                            Mike 56
                                            wrote on last edited by
                                            #33 Quote Reply

                                              Both the Swiss steel is very hard and heats up fast if you don't over heat the bit it will keep cutting and not burn up or break. When the bit is about to go though you have to go even slower so the bit does not hang up and break. If you are careful you can get one hole with a new bit. The bits i buy come in two packs that way i have a back up.
                                              pc

                                              1 Reply Last reply

                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                              With your input, this post could be even better 💗

                                              Register Login

                                              • 1
                                              • 2
                                              1. Home
                                              2. Tool Talk
                                              3. Swiss Army Knights Forum
                                              4. 84/91mm Combo Tool in Mods
                                              Reply
                                              • Reply as topic
                                              Log in to reply
                                              COMMUNITY LINKS
                                              EDC-TV SAKWiki GearFeed SAKSelector
                                              Operational Funds

                                              Help us keep the Unworkable working!

                                              Make A Donation
                                              November Goal: $300.00
                                              Due Date: Nov 30
                                              Total Receipts: $0.00
                                              Below Goal: $300.00
                                              0% funded
                                              • Login

                                              • Don't have an account? Register

                                              • Login or register to search.
                                              • First post
                                                Last post
                                              0