MT.O Prybar
-
@Mr. Whippy said:
Not totally sure (I think Shapeways discusses it) but I believe it's a stainless steel with some sort of epoxy(?) binder. I don't think corrosion is going to be a major problem.Well at least you'll not suffer the issues you suffered with the slickness of the Spirit out on the farm :D I'm not a one piece tool guy myself, but they do look cool 8)

-
From http://www.shapeways.com/materials/steel
*Shapeways 3D printed stainless steel is very strong and rigid with similar properties to 420 stainless steel, except it is infused with a bronze content of up to 30%. This gives some Stainless Steel objects a slightly bronze hue.
We deposit small drops of glue onto layers of stainless steel powder. Then a new layer of powder is spread and the process repeats until we have a fully printed tray. Then we take the printed objects out carefully. In this stage of the process, the objects are very fragile–similar to wet sand. After, we sprue the objects together and infuse them with bronze. Items closer to the bronze infusion start point will absorb more bronze. These items might look more golden than other items. We are working on standardizing the colors, but in the meanwhile, there will be some color differences in the models you may receive (see picture above). Then, we cut off the objects from the tree and polish them with a tumbler. Depending on how fragile the printed objects are we use different polishing media. This is why some objects may have a slightly shinier surface than others. After polishing,we spray on a sealant and ship to your doorstep.
This material is watertight, is dishwasher safe, not recyclable, and not foodsafe. It is heatproof to 831C/1528F degrees. Higher temperatures may significantly change material properties.*
So, it's basically steel grains welded together with bronze. I assume it would be very corrosion resistant, especially since they say it's dishwasher safe.
-
Thanks Mr. Whippy, nice write-up, glad to hear your first impressions were generally positive.
The upcoming production run should have a much better finish anyway.Mine arrived a couple of days ago:






The bottle opener has to be my favourite part as it's so much better than my other prybar.
All the hex cut-outs seem to be the right size although i can't test the smallest ones as i don't have anything suitable.@sparky415 said:
You need any electrical work doing Mate? >:D
Guess I better start saving my pennies :ahhh

Just keep an eye out for the soon to be created pass-around thread.
@stealth007s said:
If you do one with the spoke wrench I will be getting one.I had a look at adding a spoke wrench but there wasn't enough room for it anyhere sensible so i'll have a go at a bike tool soon.
@Grant Lamontagne said:
Those look great!
Does the finish seem like it might invite corrosion problems? What kind of steel was used?
Defit kinda looks like it would especially inside the lettering? JR
@50ft-trad said:
@Mr. Whippy said:
Not totally sure (I think Shapeways discusses it) but I believe it's a stainless steel with some sort of epoxy(?) binder. I don't think corrosion is going to be a major problem.
Well at least you'll not suffer the issues you suffered with the slickness of the Spirit out on the farm :D I'm not a one piece tool guy myself, but they do look cool 8)

Thanks Everyone and thanks Steinar for posting that info.
I've been carrying my first prybar on my keychain for a month or so now and haven't seen any signs of corrosion on the tool, although the hex bits gone rusty already. -
If you do one with the spoke wrench I will be getting one.
I had a look at adding a spoke wrench but there wasn't enough room for it anyhere sensible so i'll have a go at a bike tool soon.
What's wrong with making the cut-outs around the O in MT.O the right size/shape for spokes? It's not like they won't be able to hold the o-ring if they're square, right?
-
@Tofty said:
Thanks Mr. Whippy, nice write-up, glad to hear your first impressions were generally positive.
The upcoming production run should have a much better finish anyway.Mine arrived a couple of days ago:


Thanks Everyone and thanks Steinar for posting that info.
I've been carrying my first prybar on my keychain for a month or so now and haven't seen any signs of corrosion on the tool, although the hex bits gone rusty already.I really like the finish! kinda gives it that, not brand new, first deverginizing it, used, but kept in very good condition! and yeah you can see the rust forming on the bit, only problem with that is it will transfer to the tool with no hesitation! can the bit store horizontal in the wrench area? JR
-
If you do one with the spoke wrench I will be getting one.
I had a look at adding a spoke wrench but there wasn't enough room for it anyhere sensible so i'll have a go at a bike tool soon.
What's wrong with making the cut-outs around the O in MT.O the right size/shape for spokes? It's not like they won't be able to hold the o-ring if they're square, right?
There just doesn't seem to be enough room for them while maintaining the necessary material thickness around the 1/4" hex.

@MadPlumbarian said:
I really like the finish! kinda gives it that, not brand new, first deverginizing it, used, but kept in very good condition! and yeah you can see the rust forming on the bit, only problem with that is it will transfer to the tool with no hesitation! can the bit store horizontal in the wrench area? JRI have a bad habit of not wanting to use shiny new tools so this is the perfect solution; make them look ragged to begin with.
There are a number of hex bits on the market that wouldn't suffer this fate; from TiN coated to being completely made from stainless steel, in fact thats what will be accompanying my prybar during the pass-around.

A lovely Wera stainless PH2 bit.
Unfortunately a hex bit can't be stored in the wrench cutout on the MT.O prybar, thats what the little bit kit you get with forum membership is for. I wish there was room but as shown above sometimes there just isn't.
-
Dear Santa......

-
@sparky415 said:
Dear Santa......Yes, dear??
-
Are you really sure it's rust and not just the bronze starting to acquire color? We are talking about 420 type steel and bronze, I have a hard time believing it should rust easily.
-
I would have to agree Tofty. Putting the spoke wrench in that area may compromise the structure. A bike specific tool would be the only answer I think.
If you build it, we will buy it!¡!

-
Follow up:
The bit drivers and wrenches work perfectly. Very good fit.
And again, the bottle opener is flawless. :D

-
These look great! I'm drooling already! :D
Def
-
"I had a look at adding a spoke wrench but there wasn't enough room for it anyhere sensible so i'll have a go at a bike tool soon."
maybe put one on top/below the 1/4" hex driver? there are already grooves for an O-ring, shouldn't be too hard to re-design them to be spoke wrenches
-
@redbaron said:
"I had a look at adding a spoke wrench but there wasn't enough room for it anyhere sensible so i'll have a go at a bike tool soon."maybe put one on top/below the 1/4" hex driver? there are already grooves for an O-ring, shouldn't be too hard to re-design them to be spoke wrenches
That was my hunch as well, but as Tofty said it wouldn't leave enough material to warrant the bit driver's structural integrity. ;)
-
"I had a look at adding a spoke wrench but there wasn't enough room for it anyhere sensible so i'll have a go at a bike tool soon."
maybe put one on top/below the 1/4" hex driver? there are already grooves for an O-ring, shouldn't be too hard to re-design them to be spoke wrenches
That was my hunch as well, but as Tofty said it wouldn't leave enough material to warrant the bit driver's structural integrity. ;)
true
-
Dear Santa......
Yes, dear??
@Grant Lamontagne said:
These look great! I'm drooling already! :D
DefThanks guys,look out for the passaround thread if you haven't already signed up for it.
@Mr. Whippy said:
Follow up:The bit drivers and wrenches work perfectly. Very good fit.
And again, the bottle opener is flawless. :D

Excellent news and thanks for the feedback.
@Steinar said:
Are you really sure it's rust and not just the bronze starting to acquire color? We are talking about 420 type steel and bronze, I have a hard time believing it should rust easily.I haven't seen any rust at all on any of my numerous printed stainless pieces, who said that they had?
@stealth007s said:
I would have to agree Tofty. Putting the spoke wrench in that area may compromise the structure. A bike specific tool would be the only answer I think.If you build it, we will buy it!¡!

"I had a look at adding a spoke wrench but there wasn't enough room for it anyhere sensible so i'll have a go at a bike tool soon."
maybe put one on top/below the 1/4" hex driver? there are already grooves for an O-ring, shouldn't be too hard to re-design them to be spoke wrenches
That was my hunch as well, but as Tofty said it wouldn't leave enough material to warrant the bit driver's structural integrity. ;)
Lets go with a bike specific tool then, what features do you think are needed and what overall size would be preferable?
Tools:
3.23mm spoke wrench (for 15 guage spokes)
3.3mm spoke wrench (for 14 guage spokes)
etcSize:
75mm (3") by 25mm (1") by 3mm(1/8") for exampleLet me know what size of wrenches, allen keys and other tools you most often need on your bikes and i'll try to put something together.
I will start a new thread about this after i have an initial design drawn up. -
Are you really sure it's rust and not just the bronze starting to acquire color? We are talking about 420 type steel and bronze, I have a hard time believing it should rust easily.
I haven't seen any rust at all on any of my numerous printed stainless pieces, who said that they had?
Nobody, it was me misreading a post where it was pointed out the tool had no rust, while the bit had acquired a little. When I noticed my mistake it was too late to fix, so I hoped nobody would notice. No such luck. ;)
-
Looks like that would be good to start the design Tofty. I'll take a look at my ride later this evening to get size specifics. I'm sure others will do the same if they're interested. Off the top of my head, 4mm hex key is the size I probably would use the most though


-
No worries Steiner, your point was still valid.
Thanks stealth007, i'm not sure if allen keys should be part of the tool or stored as a bit like the leatherman mako.
To make allen keys on a one-piece tool thats water-jetted or lasered from sheet metal would take a number of extra machining operations but with 3D printing it's no extra effort or expense so i may well take advantage and make it a uniquely 3D printed tool which also means it doesn't have to have a constant thickness so thicker features can be added if needed.
Any other tool suggestions?
One idea i had was to make the tool in two different pieces that fitted together for storage, both with a tyre lever on one end.
On bikes is there usually an arrangement of nuts and bolts that need an allen key on one side and a nut driver on the other? If so these are tools that need to be on opposite pieces of the design. -
You know how much I like the 6mm hole for screwdriver bits, how about instead of allen keys just having a 6mm hole (or a hole in each piece?) and using ‘Allen screwdriver bits’ ?
hope that made some kind of sense

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login