I did it!!!
-
Thanks guys! I think I've figured out what the problem with the wiggle in the blade is... The blade is a tiny bit thinner than the backspring; I think I must have used the backspring from the pre '05 Explorer I used, and the blade from the new Compact I also used for parts. I just compared the blades, and the one that came from the Explorer is indeed thicker; it matches the width of the backspring exactly.
Oh well, rookie mistake I guess. 
I'm not thrilled with the idea of taking the whole thing apart again though. Is it possible to remove just the one pin, replace the blade, and put a new pin in? (I hope I have enough good bushings left if that's possible.)
I do have a pair of regular scales I'm going to use for now, but I'm going to wait to put them on until I figure out how I'm going to deal with the wiggly blade.
-
I have ground the peening a little hollow, which allows you to peen it more and tighten up the pivot.
-
The new thinner blades match with a liner that has an indention to offset the thinner blade.
-
You did it!

You'll want to swap the blade for sure, you might be able to get away with just removing that pin, but it'll be easier to redo it. Just think, you'll be faster the 2nd time anyway!
-
congrats

i'm glad you got er done! like syph007 says, it's easier and faster the second time
I'm not saying it's impossible but I think it will be very tricky to remove the pin, pull the blade and put pressure on the spring enough to get the new blade back in....
-
Nice job Heinz!¡! Can't wait to see it with the scales

-
Thanks for the encouragement guys!
The main problem I have with redoing the whole thing is that I don't have enough bushings left over. I was only able to save 8 of the 12 from the Explorer and the Compact, and only have two of those left now. Now that I've got some experience with drilling out the pins, I think I can save more the next time, but I can't be sure yet.I think it's probably best to re-do the whole thing, even though I'd rather take the lazy way out. If there's one thing I've learned in my life though, it's that doing that almost always produces second rate results I'm not happy with. Since it'd be best to do a complete re-do, I think I'll change the scissors as well, and use the ones that came with the Explorer that have the screw pivot, instead of the rivet.
Overall, in spite of my goof-up, and my ham handedness with all of this, I found the whole process to be a lot of fun! I'm looking forward to doing another one now actually. I think it might be something fun to get my son involved with too. So once I re-do the Yeoman, I think I'll do a Woodsman as my next one, to keep with the making the discontinued models theme and all... :D
-

A quick shot here to show the new and old liners next to the blades. On the new liner (top) you can see an indent that will sit next to the blade tang. This is to compensate for the slimmer tang that can be seen on the newer blade next to it. The most important thing you need to keep in mind is not to mix up old and new parts. They won’t work and the blade will sit wrong in the finished knife, striking the top of the small blade. Ask me how I know. ::)

I did exactly the same thing when I first tried modding. :-\ You have to admit that I did try and warn you. :D
-
A quick shot here to show the new and old liners next to the blades. On the new liner (top) you can see an indent that will sit next to the blade tang. This is to compensate for the slimmer tang that can be seen on the newer blade next to it. The most important thing you need to keep in mind is not to mix up old and new parts. They won’t work and the blade will sit wrong in the finished knife, striking the top of the small blade. Ask me how I know. ::)

I did exactly the same thing when I first tried modding. :-\ You have to admit that I did try and warn you. :D
Yeah, I know...
Now I know better, and I'll get it right next time! 
-
whoa, nice... makes me think I had better get of my butt and turn mine from a pile of parts into a built up knife... but I keep looking at my Pioneer solo and trying to figure out if I can modify the scales from that to build an Alox Yeoman.

then I take my medication and have a lay down.
but that solo should be nervous...
-
Nice to see you get it finished mate!

-
Cool!

Now you have yet another source of temptation when you continue trying to get that perfect SAK. :D
-
Well done mate
I really want to do a 108mm mod but not sure I have the balls to take it apart. :-\ -
Now you have yet another source of temptation when you continue trying to get that perfect SAK. :D
Yeah, no kidding! I'm already planning out what to do next.
I'm totally strapped right now, but I want to get a Swiss Champ and take the file, saw, and fish scaler out to make it into an Explorer with pliers.
-
Well done mate
I really want to do a 108mm mod but not sure I have the balls to take it apart. :-\taking it apart is the easy part ;)
I wouldn't say that... at least not for me... It took me a bit of practice to be able to drill out the pins without destroying the bushings.
-
@Heinz Doofenshmirtz said:
Well done mate
I really want to do a 108mm mod but not sure I have the balls to take it apart. :-\taking it apart is the easy part ;)
I wouldn't say that... at least not for me... It took me a bit of practice to be able to drill out the pins without destroying the bushings.
what size bit were you using?
-
Congratz on your first mod Heinz. I agree, an Exlorer with pliers would be the perfect mod :D
-
@Heinz Doofenshmirtz said:
Well done mate
I really want to do a 108mm mod but not sure I have the balls to take it apart. :-\taking it apart is the easy part ;)
I wouldn't say that... at least not for me... It took me a bit of practice to be able to drill out the pins without destroying the bushings.
what size bit were you using?
Don't remember what it was in standard, but I'm pretty sure the metric diameter was 1.8 mm. I also got a center punch to mark the pins to start drilling, and once I did that, it got a lot easier. Throttling down my drill to a lower RPM also helped.
-
I'm already planning a bladeless SAK too, for my son. I was telling him about how I'm learning to do mods, and that if he wanted to work on it with me, we could make such a beast. That way he could have it with him at school and not get into trouble for it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login