I did it!!!
-
@Heinz Doofenshmirtz said:
Well done mate
I really want to do a 108mm mod but not sure I have the balls to take it apart. :-\taking it apart is the easy part ;)
I wouldn't say that... at least not for me... It took me a bit of practice to be able to drill out the pins without destroying the bushings.
what size bit were you using?
Don't remember what it was in standard, but I'm pretty sure the metric diameter was 1.8 mm. I also got a center punch to mark the pins to start drilling, and once I did that, it got a lot easier. Throttling down my drill to a lower RPM also helped.
-
I'm already planning a bladeless SAK too, for my son. I was telling him about how I'm learning to do mods, and that if he wanted to work on it with me, we could make such a beast. That way he could have it with him at school and not get into trouble for it.
-
@Heinz Doofenshmirtz said:
I'm already planning a bladeless SAK too, for my son. I was telling him about how I'm learning to do mods, and that if he wanted to work on it with me, we could make such a beast. That way he could have it with him at school and not get into trouble for it.That would be great for your son.
Good work on the Yeoman by the way. Once you get your bearing in the MOD world I might be your first customer if you start doing work for others.
;) We can talk about it when the time comes. 
I have been thinking about getting into modding as well (SAK'S). My last project was a Micra that Steve had to put back together for me.

-
Sounds like a good plan Heinz.Not only his first SAK,but built by dad too!
-
@Heinz Doofenshmirtz said:
@Heinz Doofenshmirtz said:
[quote author=Zed link=topic=41024.msg655322#msg655322 date=1353964624]
Well done mate
I really want to do a 108mm mod but not sure I have the balls to take it apart. :-\taking it apart is the easy part ;)
I wouldn't say that... at least not for me... It took me a bit of practice to be able to drill out the pins without destroying the bushings.
what size bit were you using?
Don't remember what it was in standard, but I'm pretty sure the metric diameter was 1.8 mm. I also got a center punch to mark the pins to start drilling, and once I did that, it got a lot easier. Throttling down my drill to a lower RPM also helped.
[/quote]try a smaller bit next time, it doesn't fully hollow out pin but it also won't damage bushings...then i use a punch to gently force the pin down out of bushing making sure the other side bushing is over a hole in my mod board to allow it move out...
it's kinda like de-peening
-
@captain spaulding said:
@Heinz Doofenshmirtz said:
I'm already planning a bladeless SAK too, for my son. I was telling him about how I'm learning to do mods, and that if he wanted to work on it with me, we could make such a beast. That way he could have it with him at school and not get into trouble for it.
That would be great for your son.
Good work on the Yeoman by the way. Once you get your bearing in the MOD world I might be your first customer if you start doing work for others.
;) We can talk about it when the time comes. 
I have been thinking about getting into modding as well (SAK'S). My last project was a Micra that Steve had to put back together for me.

I doubt I'm going to be doing anything for anyone where I'm charging or asking for trades any time soon, but let me know and let's get together and I'll show you what little I've learned! I have a little spot under my workbench in the garage where one of those little "icecube" coolers fits perfectly... be great for a couple sixers of beer!
I wouldn't feel to bad about your Micra... I was afraid I'd end up in the same situation!... begging Steve or Syph to put it all back together for me...
It's like anything else, it takes courage and practice. (A mantra I've been telling my son for a few years now.
)@Heinz Doofenshmirtz said:
@Heinz Doofenshmirtz said:
[quote author=WiSAKfan link=topic=41024.msg655422#msg655422 date=1353986013]
[quote author=Zed link=topic=41024.msg655322#msg655322 date=1353964624]
Well done mate
I really want to do a 108mm mod but not sure I have the balls to take it apart. :-\taking it apart is the easy part ;)
I wouldn't say that... at least not for me... It took me a bit of practice to be able to drill out the pins without destroying the bushings.
what size bit were you using?
Don't remember what it was in standard, but I'm pretty sure the metric diameter was 1.8 mm. I also got a center punch to mark the pins to start drilling, and once I did that, it got a lot easier. Throttling down my drill to a lower RPM also helped.
[/quote]try a smaller bit next time, it doesn't fully hollow out pin but it also won't damage bushings...then i use a punch to gently force the pin down out of bushing making sure the other side bushing is over a hole in my mod board to allow it move out...
it's kinda like de-peening
[/quote]
That's kind of how I've been doing it... trying to drill down into the pin just enough to weaken the peen so I can punch it out with a pin punch. I specifically bought a new set of pin punches for this, and the center punch too. I haven't done any real machining since my shop classes in HS, but some of it's coming back to me... :)Once I get the drilling done, I've been placing the SAK over the jaws of my vise, opened just enough to allow the bushing to fit inside so the knife sits flat on top of the jaws, then punching the pin out. I put a piece of paper or a paper towel underneath it to catch the pin and bushing when it comes out.
I've found that a couple of wraps of the blue painters' masking tape around the knife, one between each set of the pins, holds everything together once all the pins are out. Next time, I'm going to be a lot more careful taking the tape off, so I can preserve the order of the parts so I don't have to figure it out all over again when I'm putting it back together.
My next project, other than swapping out the new blade for the old blade in my Yeoman, will be to do a bladeless one for my son. Not sure what model to start with yet, but he's at the age where he's really starting to get into computer gaming, and is interested in building his own PC, so I might make a bladeless CT34 for him. I'll figure it out sooner or later.
Oh, and thanks again for all the kind words and encouragement everyone! You guys are great! I love being part of this forum! You guys rock!
-
@Heinz Doofenshmirtz said:
@captain spaulding said:
[quote author=Heinz Doofenshmirtz link=topic=41024.msg655578#msg655578 date=1354048406]
I'm already planning a bladeless SAK too, for my son. I was telling him about how I'm learning to do mods, and that if he wanted to work on it with me, we could make such a beast. That way he could have it with him at school and not get into trouble for it.That would be great for your son.
Good work on the Yeoman by the way. Once you get your bearing in the MOD world I might be your first customer if you start doing work for others.
;) We can talk about it when the time comes. 
I have been thinking about getting into modding as well (SAK'S). My last project was a Micra that Steve had to put back together for me.

I doubt I'm going to be doing anything for anyone where I'm charging or asking for trades any time soon, but let me know and let's get together and I'll show you what little I've learned! I have a little spot under my workbench in the garage where one of those little "icecube" coolers fits perfectly... be great for a couple sixers of beer!
I wouldn't feel to bad about your Micra... I was afraid I'd end up in the same situation!... begging Steve or Syph to put it all back together for me...
It's like anything else, it takes courage and practice. (A mantra I've been telling my son for a few years now.
)I might be over that way tomorrow or Thursday and if so we can talk. If not im going out of town for a while so we could talk when I get back. If I do head that way tomorrow or the next day (and your around) what kind of beer do you like? I wouldn't mind putting a few back and talking tools. I can bring my EDC box of goodies. :ahhh Possible trades.
Sorry just thinking to much now. Anyways I will let you know if I will be in the area. 
On a side note I might have to take you up on your offer to sharpen my Dragonfly.
-
Tomorrow would be fine, I can make some time in the afternoon to hang out... my garage is a bit of a disaster though... but still room to work and chill...
Oh, and I'm fond of IPA's. :D Give me a ring this afternoon... I'll PM you my cell if you need it. -
heinz did you ever attempt to switch just the knife without taking it all apart?
inquiring minds want to know

-
I changed the main blade on a 6 layer Champion. I only drilled out one rivet. Not an easy job. It would be much faster and easier to dissemble the whole thing.
-
yeah it seems tricky
any tips on how you pushed the spring in order to get the blade in there?
(got an idea on the OHT but don't want to take it all apart)
-
Lot of brute force and patience. I used a screwdriver to push down on the spring. The brass rod needs to be sharpened to a point and lots of oil.
-
I can picture doing it, but I think I see why you say just to take it apart as its faster. :D
-
regarding the missing bushings,
what would happen if you peened the pins like you would on an alox for the missing bushings and then glued on cellidor?
do the bushings serve another function besides being the spot where the cellidor scales anchor too?
-
@WiSAKfan said:
regarding the missing bushings,what would happen if you peened the pins like you would on an alox for the missing bushings and then glued on cellidor?
do the bushings serve another function besides being the spot where the cellidor scales anchor too?
Ya in a pinch you could just probably use a small nut or something and glue it to the scale. If you peened without something the rivet would dome and glue wouldnt stick too well to that I would think.. but a small nut i bet would work.
-
regarding the missing bushings,
what would happen if you peened the pins like you would on an alox for the missing bushings and then glued on cellidor?
do the bushings serve another function besides being the spot where the cellidor scales anchor too?
Ya in a pinch you could just probably use a small nut or something and glue it to the scale. If you peened without something the rivet would dome and glue wouldnt stick too well to that I would think.. but a small nut i bet would work.
great quick response from a fella that would certainly know!
-
I did it too.. thanks for the kick in the pants to get this finished Heinz.

-
Once I can get some plus scales and possibly some more bushings, I'll fix mine.
I'm thinking now that I'm probably just going to redo it altogether. Use the old scissors that were in my old Explorer as well as the old blade.
I was thinking it might be possible to make bushing out of brass rod, by finding some with the same outer diameter as the bushings, and then drilling a 2.5 mm diameter whole in the center. Might be a little tricky, but with the right equipment I don't see why it couldn't be done.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
