The Commander (LM Super Charge Mod)
-
Tweezers and Toothpick/Knife grips
After failing twice at manually milling this piece from a couple of small scraps of titanium, I gave in a went digital. I've toyed with adding a plate on the sides for extra grip. I had a mildly successful attempt when I made my own "Flair", AKA The Panache. A brass plate was added, jimping was hand filed...this will be so nice.




What you are looking at are two plates that will be epoxied on the flat surfaces on the Commander, what you don't know is that they are getting printed in alumide and black plastic (for now at least) from Shapeways.

These plates serve a much more Swiss purpose than just aesthetics. Not only are they grips and jimping for the use of the outside tools, the two hollow cavities will be hold a set of Vic Classic Tweezers and Toothpick!

Here's a visual reference of how the T&T will sit.

The hole and gap in the bottom will accomodate the rivet on the side of the Commander, this also serves as a pressure point to hold the tweezer and toothpick. Here's a really bad rendering...the T&T will pull towards the knife pivots.

I ordered a set of black plastic and a set of alumide...over all $20 and should be here by the new year. Once I know they fit, I'll order the polished stainless. I'll need to some hand finishing, I didn't want to fire up SolidWorks...most because this is an extruded shape, but I also didn't want to get into 3D modelling hell.
-
"I didn't want to fire up SolidWorks...most because this is an extruded shape, but I also didn't want to get into 3D modelling hell."
clearly you haven't used autocad in 3D, now THATS hell -
One question though Eric, where/ when can I get one (or two or three.....)?


-
Vic Pen.
This one I've been chasing with a stick for a while now...I prefer the Wave over the Charge because it is slimmer and more compact, but there is certainly a lot more possibilities and hidden mini cavities on the TTI.
Taking a 91mm Vic Pen...meant for the scale of a Vic SAK plus, I saw an opportunity for it to be slotted into one of the blade chambers.
Here you can see it inside the very back of the blade slot.

Measuring it up and chucking it on up, a small notch was milled into the back edge scale, this was only two operations, fairly simple.
(look on the left side of the top scale in the photo) You'll also notice the other milled slot, that's for the ferro rod already described in a previous post.
Here you can see how tight I'll be, I ended up putting it in the SE slot for a couple of reasons. 1. I didn't want the edge on my PE to be scratched from the pen being drawn/replaced. 2. The SE snub nose tip is less dangerous in case the pen pushed it out accidentally 3. The SE has 20x more sharp edges to wear down than the PE one.

The pen was a little loose inside the newly found slot so I glued some .02mm styrene I had leftover from a vacuum forming project. That ate up the smallest of room and it also provided a nice smooth surface for the pen to ride against.

Gluing the strip down.

A rough in fit and it looks promising!

Buttoning it up!




Again, this will never replace a real pen...but if I need to grab one thing to leave the house and defend my honor with...it might be this tool!
-
@redbaron said:
"I didn't want to fire up SolidWorks...most because this is an extruded shape, but I also didn't want to get into 3D modelling hell."
clearly you haven't used autocad in 3D, now THATS hellOh yah..I know of AC3d and it's terribleness. I hope to offer the T&T if the first run fits well, I am also thinking I may add a bottom to the t and t slots so they don't ride along the actual tool itself, but it'll make them thicker.
-
"I didn't want to fire up SolidWorks...most because this is an extruded shape, but I also didn't want to get into 3D modelling hell."
clearly you haven't used autocad in 3D, now THATS hellOh yah..I know of AC3d and it's terribleness. I hope to offer the T&T if the first run fits well, I am also thinking I may add a bottom to the t and t slots so they don't ride along the actual tool itself, but it'll make them thicker.
Thats cool, I'd like one if you could mill them from Ti?
-
"I didn't want to fire up SolidWorks...most because this is an extruded shape, but I also didn't want to get into 3D modelling hell."
clearly you haven't used autocad in 3D, now THATS hellOh yah..I know of AC3d and it's terribleness. I hope to offer the T&T if the first run fits well, I am also thinking I may add a bottom to the t and t slots so they don't ride along the actual tool itself, but it'll make them thicker.
Thats cool, I'd like one if you could mill them from Ti?
It would be made from stainless. It'll look Ti, it's stainless powder infused with bronze.
-
I have some carbon fiber laying around. I may give it a try :) I have access to a mill tomorrow for a few, might be a good chance to mill the slots. Thanks for the great idea :)
-
@tattoosteve99 said:
I have some carbon fiber laying around. I may give it a try :) I have access to a mill tomorrow for a few, might be a good chance to mill the slots. Thanks for the great idea :)I used the profile of the blades for the top. Be sure to mill enough material off the off so when the Pliers are open they will clamp down all the way.
-
Today's bumming around the house doing random stuff.

-
Blast! The minimal wall thickness is 1mm, I'll need to redesign It and shoot it back to shape ways.
No need to fear!
-
Wow that is awesome yet another masterpiece
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
-
I am secretly working on a bit holder (MUT style) with the same part. Might be a 'bit' tight :)

I'll have to upload this to my order now on shapeways, plastic and aluminum.
If these make the cut, I'll expand it by 2% and then get them done in Stainless (there is shrinkage!)
Sent from my iPad using Tapatalk HD
-
-
I took this one out of enki_ck's book:
VIC SCISSORS!
Easiest scissor mod, no need to pin anything, just simply needed to bore out the pivot hole from 3mm to 7/32. Again, carbide bits made this easy. Since I already pushed in the liner lock so it wouldn't push up against the scissors, this was a simple drop in.
Seriously....no mods whatsoever.

The Vic's scissors are going to leave plenty of room for the ferro rod, whenever they get here..


They are a pleasure to use like all Vic scisssors, not as cool or as crisp as the Gerber ones but these are much more accessible and cheaper. A simple, even used SAK can be used to harvest a pair.


-
I like that a lot

-
Nice addition. Glad you changed your mind about the Vic scissors. They look like they belong there.

-
could you do the pen mod on a wave?
-
Cool scissor mod! I love Vic scissors

-
@enki_ck said:
Nice addition. Glad you changed your mind about the Vic scissors. They look like they belong there.
I never said I wouldn't do it...just wanted to try :)
I am trying to see if I can, it would be pretty neat. I'll likely start a Wave Master (get it...Master & Commander) project
Thanks! So easy, so clean.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
