Best SAK Ever!!!
-
I've lost count of the thing's I've used that saw for, and it'd never needed sharpening!
-
I would say the Swisschamp but it is a too big sometimes . Its got to be a Climber paired with a Swisstool
Not alot comes close .Dunc
-
Maybe we should have a poll ???
-
A Spartan you say

-
They do one that comes without the key ring as well. :D
-
@NutSAK said:
In your opinion, how is it "better"? The Farmer's woodsaw is longer than the Spirit's. IMO, that is "better".I don't own either Spirit or Farmer, but have briefly handled them in a store.
So, perhaps I am mis-remembering...
But, doesn't the Spirit woodsaw lock open? And, doesn't the Farmer not have a locking woodsaw?
I didn't directly compare saw lengths between Spirit and Farmer, but surely there isn't that much of a difference...
@ringzero said:
A Farmer can't turn phillips head screws?In my experience, the end of the can opener works better for turning phillips screws than the backspring phillips, unless the head of the screw is in tight quarters. The backspring phillips is too polished and rounded to grab many screws, and has a very short reach due to the T-handle setup.
Perhaps I should have been more explicit in my example: "holding a nut with the Spirit's pliers while turning a RECESSED bolt using the Tinker's Phillips driver"
I've used a SAK can opener to turn Phillips screws when the SAK I was using lacked a dedicated Phillips. Mostly it worked out OK, but I also recall buggering up some Phillips screws when turning them with the can opener.
So, in general I'd prefer to use the SAK dedicated Phillips driver rather than the can opener. Plus, I encounter lots of recessed Phillips that the can opener won't even touch.
.
-
The saw on the Spirit does indeed lock open, but I've never had a Farmer saw blade fold on me, so I think it's a moot point, regarding the lock (or lack there off), the greater length of the Farmer however is hard to argue with :)
-
@ringzero said:
So, in general I'd prefer to use the SAK dedicated Phillips driver rather than the can opener. Plus, I encounter lots of recessed Phillips that the can opener won't even touch.You should try a model with the in-line phillips driver if you haven't. It's the best of both worlds. It fits more heads, gets into tight areas, and has great reach.
I've buggered-up many more phillips screws with that over-polished backspring phillips than anything else. Out of the 60 SAKs I own, I now only have one that has the backspring phillips, and that's just because I can't find a SAK that has the same implements as a Deluxe Tinker w/a corkscrew instead of the phillips.
-
I agree, the inline one is far better. :) I just wish it didn't have to come on the same layer as a magnifyer. :(
-
Yep the inline is far better, until it closes on your fingers :o
-
@micky d said:
The saw on the Spirit does indeed lock open, but I've never had a Farmer saw blade fold on me, so I think it's a moot point, regarding the lock (or lack there off), the greater length of the Farmer however is hard to argue with :)I'm not arguing with it.
Since you own both, perhaps you could enlighten me as to the difference in length?
Personally, I'd prefer to have a slightly shorter locking saw to a slightly longer saw that didn't lock.
.
-
-
I agree, the inline one is far better. :) I just wish it didn't have to come on the same layer as a magnifyer. :(
...or that crappy LED.
I find uses for the magnifier, but most of the time I just put up with it as a consequence of needing the phillips. :)
Ever come across any mods that don't have either of these?
-
@micky d said:
Yep the inline is far better, until it closes on your fingers :oI've never had that happen, but I have had the backspring one close on me.
Have you tried the newer phillips that comes with the new design magnifier? The backspring engages a slot in the back of the driver, and works as a passive "lock" that keeps it snapped open pretty tightly.
-
@micky d said:
The saw on the Spirit does indeed lock open, but I've never had a Farmer saw blade fold on me, so I think it's a moot point, regarding the lock (or lack there off), the greater length of the Farmer however is hard to argue with :)
I'm not arguing with it.
Since you own both, perhaps you could enlighten me as to the difference in length?
Personally, I'd prefer to have a slightly shorter locking saw to a slightly longer saw that didn't lock.
.
There's not much in it, (just ran up stairs to check :D) maybe 5-6 mm, I've got to admit to being suprised at that as it feels longer

-
@micky d said:
Yep the inline is far better, until it closes on your fingers :o
I've never had that happen, but I have had the backspring one close on me.
Have you tried the newer phillips that comes with the new design magnifier? The backspring engages a slot in the back of the driver, and works as a passive "lock" that keeps it snapped open pretty tightly.
Nope, not tried the newer design yet :), good to see that Vic are still tweaking the design though :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login