Spirit owners club
-
@50ft-trad said:
Buying my first Spirit today! Still deciding between the X and the RT.
I'd say it depends on how much money you want to spend as they are functionally the same. I really want the RT Edition though
I have the regular Spirit with the "butterblade".Yup, the RT is the X in a tux :D
Nice way of putting it

+1
Al always was a smooth talker. :D
-
@armèe-suisse said:
Spirit RT ;)Spirit, Spirit RT, Spirit S BO
i like how the box you had it on says not to use blades. irony.
-
I finally got around to purchasing a Spirit X last week, after years of using the original Spirit with the butter blade.

I will say that I'm a tad bummed out about the size of the new blade on the Spirit X. It actually looks like it started off as a butter blade, and Victorinox just ground it down to it's new shape. There's a lot less steel than there is on a butter blade, and certainly much less than there could be.
On the positive side, it looks like Victorinox was not happy with near-perfection in the fit and finish department, and took it to a new level. My older Spirit is no slouch, but the new one is closer to perfection than I would have imagined.
I will admit that I kind of liked the old logo better on the outside of the tool, and miss the logo on the pliers, but not enough to give it a third thought.
Now to find the perfect pocket clip for the Spirit........
-
@Buzzbait said:
I finally got around to purchasing a Spirit X last week, after years of using the original Spirit with the butter blade.
I will say that I'm a tad bummed out about the size of the new blade on the Spirit X. It actually looks like it started off as a butter blade, and Victorinox just ground it down to it's new shape. There's a lot less steel than there is on a butter blade, and certainly much less than there could be.
On the positive side, it looks like Victorinox was not happy with near-perfection in the fit and finish department, and took it to a new level. My older Spirit is no slouch, but the new one is closer to perfection than I would have imagined.
I will admit that I kind of liked the old logo better on the outside of the tool, and miss the logo on the pliers, but not enough to give it a third thought.
Now to find the perfect pocket clip for the Spirit........
I'm too looking for a nice pocketclip for my Road Tour Spirit:
http://www.niteize.com/product/HipClip.asp
http://dx.com/p/nite-ize-stainless-steel-cell-phone-self-locking-clip-silver-70239
http://miltner-adams.com/ma_incredible-slc.htmlDid you find the perfect clip?
-
I have A HipClip and a ClipDraw on the way, for testing. :D
--
sent via carrier pigeon from my secret hideout -
My HipClip arrived. For me, it's just too large to use on the Spirit. I'd grind it down and make it right size, but the adhesive strip is pre-applied, and it doesn't come with any extra strips. I may have to order a small roll of 3m tape.


--
sent via carrier pigeon from my secret hideout -
@Buzzbait said:
My HipClip arrived. For me, it's just too large to use on the Spirit. I'd grind it down and make it right size, but the adhesive strip is pre-applied, and it doesn't come with any extra strips. I may have to order a small roll of 3m tape.Good to know.
The Clip Draw looks nice to me, not cheap, but it comes at least with extra strips. :D
I wish it was more low riding.. -
The Clip Draw looks nice to me, not cheap, but it comes at least with extra strips. :D
I wish it was more low riding..I agree. To get exactly what I want, I think I'm either going to have to grind down the HipClip, or tap a low ride clip to fit onto the ClipDraw base.
--
sent via carrier pigeon from my secret hideout -
I got the ClipDraw today, but I think it's better suited to maybe my Rebar.
So I thinned out the HipClip on a belt sander, gave it a good hand wet/dry sanding to remove the NiteIze logo and the burrs, and used an adhesive strip from the ClipDraw to mount it. I'm quite happy. Nice deep pocket carry. It even makes the tool feel less slippery.



--
sent via carrier pigeon from my secret hideout -
@Buzzbait said:
I got the ClipDraw today, but I think it's better suited to maybe my Rebar.So I thinned out the HipClip on a belt sander, gave it a good hand wet/dry sanding to remove the NiteIze logo and the burrs, and used an adhesive strip from the ClipDraw to mount it. I'm quite happy. Nice deep pocket carry. It even makes the tool feel less slippery.



--
sent via carrier pigeon from my secret hideoutI Really like the look of the new formed hip clip! Nice work!!
-
Looks perfect! Nice job

-
very nice job mate.

-
ABOUT THE CLIPDRAW...
The following is a public service announcementThis is my personal experience and yours may vary, but here goes. The front screw hole on the clipdraw does not have enough metal surrounding it to bear repeated flexing without failing. I used it maybe 15 times for actual carry. Perhaps mine wasn't heat treated correctly. Clipdraw said they would replace it but I never heard from them again. I would definitely stick with the hipclip instead.

-
:o
-
Thanks for the warning .
Chris
-
Modded Clipdraw for the win

That's about the nicest looking solution I have seen yet

-
Buzzbait, that Hipclip mod is wonderful.
-
I agree, nice job on the clip
However, I don't think I could put a clip on those beautiful Spirits. I love the smooth, mirror finish. Although it would still have the other side to look at :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


