DIY Canvas Micarta
-
LOL I do really like the old socks idea.

I'll have to think up a nifty idea to give this a test with.
-
Its all nice but I really love that bail

-
just layed up a slab of HI-Viz Vest orange using Polyester casting resin.. will be interesting to see how that turns out.
-
Nice! Def let us know!
-
When you do this type of material making, are bubbles ever an issue, or as long as you have it clamped good enough the air gets squeezed out?
-
they usually get squeezed out and as you build up the layers you work any bubbles out as you go.
But it's not the end of the world as bubbles and wrinkles add character as you sand it back and any voids can be filled by mixing up a teaspoon if resin and filling the hole and then sanding back again.
-
I’m looking forward to seeing the orange

I’ve never had problems with voids, the only problems were dry areas caused by not using enough resin or mixing up too much resin at one time and suffering with premature hardening :ahhh
In the past I've made micarta with a couple of pieces of wood clamped together now I use a simple press made from a couple of bits of MDF (medium density fibreboard) and four bolts

-
I am now a little wary of working with epoxy resins. I once was working the stuff and had my face swell up everywhere that was not covered my respirator mask. I guess my skin did not like the vapors. I did not notice it at the time but my wife sure did! :o And off to the clinic.
-
Yes, epoxy can be nasty stuff. Some people are more sensitive than others to it and some are quite allergic.
Even if it doesn't seem to effect you, repeated exposure can cause a "learned" reaction.
-
i thought synthetics didn't bond to well with epoxy resin and thats why people stress pure cotton or paper in DIY Mircarta... i always used denim and cotton instead of fiberglass matting for repairs

-
@Santos,
It seems to work best when the resin really soaks in to the material so cotton/denim is great, I have had no problems with High visibility jackets which are nylon (I think), The only thing that has not worked for me was a waterproof (lovely orange
) jacket, it just peeled apart in my hands :(Here's the press I made from some some 22mm MDF offcuts
You really only need a couple of flat bits of wood and some clamps (or even just stack some bricks on top of the wood) I use little plastic spacers to keep the Micarta parallel ;)

-
Hmmmm...... I've got a strip of orange nylon/canvas/cotton/whatever belt. Wonder if I could double layer it and soak the crap out of it.
-
There are a few other Micarta bits here ;)
</post/496407>
</post/465263>
And a nice tutorial over on British Blades

http://www.britishblades.com/forums/content.php?82-Home-grown-micarta-(picture-intensive)
-
As promised (or threatened) earlier I have got around to doing up some paper micarta blanks.
The top 4 or 6 layers in each blank have the image printed in them so there is room for sanding without losing the print.
I think there could be no better adornment for "the little red knife" than Jessica Rabbit, the ultimate redhead.


-
Ive wondered how well that would work, and now I'll find out! Nice work!

-
Mmmmmm jessica rabbit :D
-
The top 4 or 6 layers in each blank have the image printed in them so there is room for sanding without losing the print.
Great idea!

I've been slightly let down by technology there... I printed these on a colour Laser printer and the image sits on the top of the paper. When you sand it the toner sands away and leaves bare paper before you get to the next image. Should have done them on an inkjet printer set for coated paper and let the ink soak into the paper. Never mind, the second set are salvageable and I know how I can use the other sets of prints that I have sitting here.
-
The top 4 or 6 layers in each blank have the image printed in them so there is room for sanding without losing the print.
Great idea!

I've been slightly let down by technology there... I printed these on a colour Laser printer and the image sits on the top of the paper. When you sand it the toner sands away and leaves bare paper before you get to the next image. Should have done them on an inkjet printer set for coated paper and let the ink soak into the paper. Never mind, the second set are salvageable and I know how I can use the other sets of prints that I have sitting here.
Oh right I wouldn't have thought of that either, but it makes sense now that I think about.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



