DIY Canvas Micarta
-
I am now a little wary of working with epoxy resins. I once was working the stuff and had my face swell up everywhere that was not covered my respirator mask. I guess my skin did not like the vapors. I did not notice it at the time but my wife sure did! :o And off to the clinic.
-
Yes, epoxy can be nasty stuff. Some people are more sensitive than others to it and some are quite allergic.
Even if it doesn't seem to effect you, repeated exposure can cause a "learned" reaction.
-
i thought synthetics didn't bond to well with epoxy resin and thats why people stress pure cotton or paper in DIY Mircarta... i always used denim and cotton instead of fiberglass matting for repairs

-
@Santos,
It seems to work best when the resin really soaks in to the material so cotton/denim is great, I have had no problems with High visibility jackets which are nylon (I think), The only thing that has not worked for me was a waterproof (lovely orange
) jacket, it just peeled apart in my hands :(Here's the press I made from some some 22mm MDF offcuts
You really only need a couple of flat bits of wood and some clamps (or even just stack some bricks on top of the wood) I use little plastic spacers to keep the Micarta parallel ;)

-
Hmmmm...... I've got a strip of orange nylon/canvas/cotton/whatever belt. Wonder if I could double layer it and soak the crap out of it.
-
There are a few other Micarta bits here ;)
</post/496407>
</post/465263>
And a nice tutorial over on British Blades

http://www.britishblades.com/forums/content.php?82-Home-grown-micarta-(picture-intensive)
-
As promised (or threatened) earlier I have got around to doing up some paper micarta blanks.
The top 4 or 6 layers in each blank have the image printed in them so there is room for sanding without losing the print.
I think there could be no better adornment for "the little red knife" than Jessica Rabbit, the ultimate redhead.


-
Ive wondered how well that would work, and now I'll find out! Nice work!

-
Mmmmmm jessica rabbit :D
-
The top 4 or 6 layers in each blank have the image printed in them so there is room for sanding without losing the print.
Great idea!

I've been slightly let down by technology there... I printed these on a colour Laser printer and the image sits on the top of the paper. When you sand it the toner sands away and leaves bare paper before you get to the next image. Should have done them on an inkjet printer set for coated paper and let the ink soak into the paper. Never mind, the second set are salvageable and I know how I can use the other sets of prints that I have sitting here.
-
The top 4 or 6 layers in each blank have the image printed in them so there is room for sanding without losing the print.
Great idea!

I've been slightly let down by technology there... I printed these on a colour Laser printer and the image sits on the top of the paper. When you sand it the toner sands away and leaves bare paper before you get to the next image. Should have done them on an inkjet printer set for coated paper and let the ink soak into the paper. Never mind, the second set are salvageable and I know how I can use the other sets of prints that I have sitting here.
Oh right I wouldn't have thought of that either, but it makes sense now that I think about.
-
It's going to be very cool when you get it working!

-
These are progress pictures, There is still one process to go but as I'm making it up as I go along with salvaging these scales I could wreck them at any time so unfinished photos are better than none.
If the next step works (clear coat over the resin) I will post some completed shots. But here is the state of play at the moment.



Being a Recruit it gets to go in my Recruit Parade, but I'm sure it would get kicked out for turning up to parade dressed like that.
-
Looks pretty cool to me!
-
Thats great Peter

-
The top 4 or 6 layers in each blank have the image printed in them so there is room for sanding without losing the print.
Great idea!

I've been slightly let down by technology there... I printed these on a colour Laser printer and the image sits on the top of the paper. When you sand it the toner sands away and leaves bare paper before you get to the next image. Should have done them on an inkjet printer set for coated paper and let the ink soak into the paper. Never mind, the second set are salvageable and I know how I can use the other sets of prints that I have sitting here.
I saw this post and the idea a creating my own images to use in my scales is great. One thing I'd like to know: you mention the last layers having the same image. So, you have the same image printed in several pieces of paper and you put the resin over one and then put the other print over, aligned, is that it?
With the epoxy over the image, isn't it very hard to perfectly align the images so that if you remove too much of one layer the underlying layer image is perfectly aligned? Just 1mm to the side and you can ruin the whole scale.
How do you make sure the alignment is... well, aligned?!...
??? -
I left the paper a couple of inches longer than needed and after lining the layers up dry I stapled them together.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



