How to build a modern golfer (84mm cellidor)
-
Just pop the scales back on and there we have it... an 84mm golfer made with all current parts!
I love these things and I see why they were a popular SAK when they were being made.







Here is the golfer posed with it's bigger brother the 91mm compact.

This was a fun little mod, and next I think will be an 84mm super tinker.
Cheers
-
-
That's an excellent how to and a great mod. I'll sticky it for refernce later but after people see it cause as we all know, nobody reads the stickies.
Great job there. Thanks! 
-
Very cool. Love the ingenuity.
-
Brilliant! Thanks for putting this up - really clear steps and pics. Thanks for taking the time.

-
Thanks all! I've been meaning to document the scissors mod for 84s for awhile, so it seemed like a good opportunity since I wanted to make a golfer anyhow. I wrecked many sets of scissors experimenting, so I thought if I showed how I do it now, that it might save others the aggravation.

These scales have the pin hole and I can add the corkscrew driver, making it only lack the pen of its big brother compact. I really like the little 84 size and it is sad that Vic stopped making scissors for them.
Cheers
-
-
When I say grind, I mean my bench belt sander. It takes off metal very fast and it's just a cheap $80 one that uses a 1x30 belt. For example to remove the metal for the pivot reshaping takes less than a minute.
Mine looks similar to this.
-
-
@hiljentaa said:
Nice! You should do an Apprentice like this. I can't seem to find one anywhere...Ah the apprentice would be a quick build as its basically a waiter with the phillips instead of corkscrew. So you can just buy a waiter and swap in the phillips. The back phillips and corkscrews are identical between the 84 and 91 size.
-
Nice! You should do an Apprentice like this. I can't seem to find one anywhere...
Ah the apprentice would be a quick build as its basically a waiter with the phillips instead of corkscrew. So you can just buy a waiter and swap in the phillips. The back phillips and corkscrews are identical between the 84 and 91 size.
TIL. Thanks! I'll put that on the 'to-do' list.

-
Nice! You should do an Apprentice like this. I can't seem to find one anywhere...
Ah the apprentice would be a quick build as its basically a waiter with the phillips instead of corkscrew. So you can just buy a waiter and swap in the phillips. The back phillips and corkscrews are identical between the 84 and 91 size.
TIL. Thanks! I'll put that on the 'to-do' list.

there's even a "how-to" thread for Phillips/corkscrew; </post/166447>

-
Outstanding job Syph - thanks for the great walk through

-
Nice! You should do an Apprentice like this. I can't seem to find one anywhere...
Ah the apprentice would be a quick build as its basically a waiter with the phillips instead of corkscrew. So you can just buy a waiter and swap in the phillips. The back phillips and corkscrews are identical between the 84 and 91 size.
TIL. Thanks! I'll put that on the 'to-do' list.

there's even a "how-to" thread for Phillips/corkscrew; </post/166447>


Endless amounts of excellent information here! Thanks.
-
@Syph007 said:
Ok this is how I make my backsprings. The modern backspring will become the scissor rest and the older backspring will become the body of the spring.Now... since the stock hole in the modern rest is 2.5mm and I want it to be 2.2mm for an 84mm mod, what do we do?
We use a bushing! Now since the difference between 2.5 and 2.2 mm is not very much material for a bushing, I started by drilling out the hole to 1/8 inch since thats the size of carbide bit I had handy. The size isnt important at all, as long as its bigger.
Then take a small piece of brass (or nickel silver) and beat it into the hole, hit it hard on both sides so it is good and stuck into the hole. Then cut the excess off each side and sand flat and you end up with this.

I only have non carbide 2.2 mm drill bits, but since we are now drilling through soft brass it's no big deal, so center punch to mark and drill away. It isnt even critical at this stage to get it dead center as you will see later on.

And test to make sure the 2.2mm brass stock fits, and we have successfully reduced the hole size to what we need.


Love to have a go at this but just wondering if it is easily achievable just using the old style scissor spring? I do have both available but would rather keep the newer one for another build if possible. I do have two old ones though if that could work too?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login