Skip to content
  • Categories
  • Recent
  • Popular
  • World
Skins
  • Light
  • Dark

Collapse

NodeBB

"How-to" for 58mm modding - Pic Heavy

Scheduled Pinned Locked Moved The Mod Squad
24 Posts 1 Posters 17.5k Views
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • J
    J
    jrp316
    wrote on last edited by
    #4

    Bushings installed and cutting the pin to length using a liner as a gauge (I read about this technique here, not sure who to give credit though...whoever you are, thanks!).

    I couldn't get a good pic of the bushings to show their orientation, so remember: the lip of the bushing should be at the top. While the knife is on the assembly board, you can cut the pins to proper length and file/peen the ends enough to fill the bushing, then finish peening on the opposing side. You'll waste a little bit of pin stock using this method, but it's a good tradeoff in ease of assembly.

    Finished peening:

    On the subject of peening, a little is a lot. After you cut the pin to length and file it down good and flat, make sure that you only have at most 1mm standing up from the bushing. Too much and you'll end up cracking/bending the pin before it's peened. I use a dime as a gauge (a dime is 1.3mm thick) and eyeball it from there. I shoot for .8 to 1mm to start peening.

    As shown above, a proper anvil surface is essential (I use a bench block, heavy block of steel). You can literally see the pin forming into a rivet head with each hit of the hammer. Use relatively gentle hammer blows; the weight of the tool will do most of the work for you. Let it.

    Your goal here is twofold: fill the bushing and eliminate side play in the tool served by that pin. Once the side play is good and gone, you're done. I like to start with 4-6 blows on the center of the pin followed by finishing up with mushrooming the head by hitting around the edges. I've found that getting most of the play out at first in all four pins, then fine tuning it from there is quite effective. Don't overpeen or you'll have lazy, binding tools (ask me how I know :P).

    1 Reply Last reply
    0
    • J
      J
      jrp316
      wrote on last edited by
      #5

      And now...the money shot!

      Red scales installed with tweezers and a pen scale on the back side. Hope you guys enjoyed this (or I at least cured your insomnia) as much as I enjoyed building it! :climber:

      1 Reply Last reply
      0
      • nuphoriaN
        nuphoriaN
        nuphoria
        Admin Team
        wrote on last edited by
        #6

        Great stuff :tu:

        I think this may to be a sticky... what do others think - useful guide?

        1 Reply Last reply
        0
        • Syph007S
          Syph007S
          Syph007
          Global Moderators
          wrote on last edited by
          #7

          Hey thanks for taking the time to post up all the pics. :tu: I love to see how other folks work on SAKs.

          So far Ive only tore down one 58 rambler, but I have an obscene amount of donor 58s coming in, and Im excited to build my mini monster. Still scratching my head on how to include the T&T on an alox version, but I think maybe making an inner layer that takes them is the only way to go.

          I think the idea on the monster 58 build page would work just fine.

          1 Reply Last reply
          0
          • enki_ckE
            enki_ckE
            enki_ck
            Global Moderators
            wrote on last edited by
            #8

            That's a great how to. :salute: I've been planing on doing that mod for some time now and this will surely come in handy. 🙂 Thanks for that. :tu:

            1 Reply Last reply
            0
            • crackoutC
              crackoutC
              crackout
              wrote on last edited by
              #9

              I always loved the way these countered springs work.

              1 Reply Last reply
              0
              • ReinierR
                ReinierR
                Reinier
                wrote on last edited by
                #10

                remember: belly in. Easy for me to remember because that's what I think when I go to the beach

                :rofl:

                +1 🙂

                Great how-to by the way :tu:

                1 Reply Last reply
                0
                • GarethG
                  GarethG
                  Gareth
                  Admin Team
                  wrote on last edited by
                  #11

                  A great guide mate, thanks for taking the time. :tu:

                  1 Reply Last reply
                  0
                  • J
                    J
                    jrp316
                    wrote on last edited by
                    #12

                    Thanks to everyone for your positive reviews and comments! If you guys want to sticky this, I'd definitely feel honored.

                    1 Reply Last reply
                    0
                    • K
                      K
                      KTesh
                      wrote on last edited by
                      #13

                      Perhaps a "Lord of the Stickies", One sticky to rule them all? Just one with a "How-to" label and links to the appropriate knife types. Problem is that it would have to be able to be edited after the editing cutoff has passed, and a mod (or two) may have to babysit it to add new links.

                      If not, then stick it because the info is very useful, and I've found that searches can be frustrating due to the nature of overlapping topics.

                      (BTW, Nice job on the mod! :tu:)

                      1 Reply Last reply
                      0
                      • MetropolicityM
                        MetropolicityM
                        Metropolicity
                        wrote on last edited by
                        #14

                        @Syph007 said:
                        Hey thanks for taking the time to post up all the pics. :tu: I love to see how other folks work on SAKs.

                        So far Ive only tore down one 58 rambler, but I have an obscene amount of donor 58s coming in, and Im excited to build my mini monster. Still scratching my head on how to include the T&T on an alox version, but I think maybe making an inner layer that takes them is the only way to go.

                        I think the idea on the monster 58 build page would work just fine.

                        If you need that part designed and laser cut from clear acrylic, let me know. I have been after a mini monster since I saw it!

                        1 Reply Last reply
                        0
                        • enki_ckE
                          enki_ckE
                          enki_ck
                          Global Moderators
                          wrote on last edited by
                          #15

                          @KTesh said:
                          **Perhaps a "Lord of the Stickies", One sticky to rule them all? **Just one with a "How-to" label and links to the appropriate knife types. Problem is that it would have to be able to be edited after the editing cutoff has passed, and a mod (or two) may have to babysit it to add new links.

                          If not, then stick it because the info is very useful, and I've found that searches can be frustrating due to the nature of overlapping topics.

                          (BTW, Nice job on the mod! :tu:)

                          They are already in the works for a few days now, the SAK MOD How to thread has already been stickied and we are gathering data for the Multitool mod link thread.

                          1 Reply Last reply
                          0
                          • Syph007S
                            Syph007S
                            Syph007
                            Global Moderators
                            wrote on last edited by Syph007
                            #16

                            @Metropolicity said:

                            @Syph007 said:

                            Hey thanks for taking the time to post up all the pics. :tu: I love to see how other folks work on SAKs.

                            So far Ive only tore down one 58 rambler, but I have an obscene amount of donor 58s coming in, and Im excited to build my mini monster. Still scratching my head on how to include the T&T on an alox version, but I think maybe making an inner layer that takes them is the only way to go.

                            I think the idea on the monster 58 build page would work just fine.

                            If you need that part designed and laser cut from clear acrylic, let me know. I have been after a mini monster since I saw it!

                            That might be faster... hmm. I started prototyping one from polycarbonate to see how I like the idea though. I just have to cut the channels for the T&T. I couldnt decide it it should clear or solid. I'll make one with the polycarb and if I dont like it, I'll probably do polished Ti as I have some scrap the right size. Luckily 1/8 material works perfect and since this is for a monster extra width isnt a big deal. 😄

                            Both tools actually fit nicely horizontally, but its not possible to actually remove them once you have liners on, so that method pictured is the only decent way to do it that I can think of. Its just a matter of leaving the tiniest lip exposed to get them out.

                            1 Reply Last reply
                            0
                            • K
                              K
                              KTesh
                              wrote on last edited by
                              #17

                              @Syph007 said:

                              @Metropolicity said:

                              @Syph007 said:

                              Hey thanks for taking the time to post up all the pics. :tu: I love to see how other folks work on SAKs.

                              So far Ive only tore down one 58 rambler, but I have an obscene amount of donor 58s coming in, and Im excited to build my mini monster. Still scratching my head on how to include the T&T on an alox version, but I think maybe making an inner layer that takes them is the only way to go.

                              I think the idea on the monster 58 build page would work just fine.

                              If you need that part designed and laser cut from clear acrylic, let me know. I have been after a mini monster since I saw it!

                              That might be faster... hmm. I started prototyping one from polycarbonate to see how I like the idea though. I just have to cut the channels for the T&T. I couldnt decide it it should clear or solid. I'll make one with the polycarb and if I dont like it, I'll probably do polished Ti as I have some scrap the right size. Luckily 1/8 material works perfect and since this is for a monster extra width isnt a big deal. 😄

                              Both tools actually fit nicely horizontally, but its not possible to actually remove them once you have liners on, so that method pictured is the only decent way to do it that I can think of. Its just a matter of leaving the tiniest lip exposed to get them out.

                              Uhm... Where's the Pin's slot?

                              1 Reply Last reply
                              0
                              • AHBA
                                AHBA
                                AHB
                                Admin Team
                                wrote on last edited by
                                #18

                                Great guide.. :hatsoff:

                                1 Reply Last reply
                                0
                                • Syph007S
                                  Syph007S
                                  Syph007
                                  Global Moderators
                                  wrote on last edited by
                                  #19

                                  @KTesh said:

                                  @Syph007 said:

                                  @Metropolicity said:

                                  @Syph007 said:

                                  Hey thanks for taking the time to post up all the pics. :tu: I love to see how other folks work on SAKs.

                                  So far Ive only tore down one 58 rambler, but I have an obscene amount of donor 58s coming in, and Im excited to build my mini monster. Still scratching my head on how to include the T&T on an alox version, but I think maybe making an inner layer that takes them is the only way to go.

                                  I think the idea on the monster 58 build page would work just fine.

                                  If you need that part designed and laser cut from clear acrylic, let me know. I have been after a mini monster since I saw it!

                                  That might be faster... hmm. I started prototyping one from polycarbonate to see how I like the idea though. I just have to cut the channels for the T&T. I couldnt decide it it should clear or solid. I'll make one with the polycarb and if I dont like it, I'll probably do polished Ti as I have some scrap the right size. Luckily 1/8 material works perfect and since this is for a monster extra width isnt a big deal. 😄

                                  Both tools actually fit nicely horizontally, but its not possible to actually remove them once you have liners on, so that method pictured is the only decent way to do it that I can think of. Its just a matter of leaving the tiniest lip exposed to get them out.

                                  Uhm... Where's the Pin's slot?

                                  Ha, good point. Might as well add the pin too!

                                  1 Reply Last reply
                                  0
                                  • K
                                    K
                                    KTesh
                                    wrote on last edited by
                                    #20

                                    @Syph007 said:

                                    @KTesh said:

                                    @Syph007 said:

                                    @Metropolicity said:

                                    [quote author=Syph007 link=topic=43271.msg1#msg1 date=1361540260]
                                    Hey thanks for taking the time to post up all the pics. :tu: I love to see how other folks work on SAKs.

                                    So far Ive only tore down one 58 rambler, but I have an obscene amount of donor 58s coming in, and Im excited to build my mini monster. Still scratching my head on how to include the T&T on an alox version, but I think maybe making an inner layer that takes them is the only way to go.

                                    I think the idea on the monster 58 build page would work just fine.

                                    If you need that part designed and laser cut from clear acrylic, let me know. I have been after a mini monster since I saw it!

                                    That might be faster... hmm. I started prototyping one from polycarbonate to see how I like the idea though. I just have to cut the channels for the T&T. I couldnt decide it it should clear or solid. I'll make one with the polycarb and if I dont like it, I'll probably do polished Ti as I have some scrap the right size. Luckily 1/8 material works perfect and since this is for a monster extra width isnt a big deal. 😄

                                    Both tools actually fit nicely horizontally, but its not possible to actually remove them once you have liners on, so that method pictured is the only decent way to do it that I can think of. Its just a matter of leaving the tiniest lip exposed to get them out.

                                    Uhm... Where's the Pin's slot?

                                    Ha, good point. Might as well add the pin too!
                                    [/quote]

                                    I'm not familiar with the specs of the knife you are making, but would a pen/stylus fit too?

                                    1 Reply Last reply
                                    0
                                    • O
                                      O
                                      oreogaborio
                                      wrote on last edited by oreogaborio
                                      #21

                                      Syph, I might have an idea... 😄

                                      1 Reply Last reply
                                      0
                                      • O
                                        O
                                        oreogaborio
                                        wrote on last edited by oreogaborio
                                        #22

                                        Yup... I def have an idea... PM inbound 😉

                                        1 Reply Last reply
                                        0
                                        • J
                                          J
                                          Josh613
                                          wrote on last edited by
                                          #23

                                          How hard is it to make a Alox rambler? I have a alox classic and the combo tool from a minichamp

                                          1 Reply Last reply
                                          0

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          • Login

                                          • Don't have an account? Register

                                          • First post
                                            Last post
                                          0
                                          • Categories
                                          • Recent
                                          • Popular
                                          • World