Show off your Sak mod's!
-
Thx. :)
@Syph. I would suggest a mixure of technique as shown above and one called "Tauschieren" in Germany. Have a look here:
http://www.entdecke-schmuck.eu/94464514nx1490/goldschmiedekurs-�-do-it-yourself-anleitungen-zum-selbermachen-f63/antike-tauschiertechnik-t2749.htmlWhat's different to Tauschieren: The inlay is hard but the brass scale is soft.
I would suggust to peen and scratch the outline of the inlay into the brass scale. But at least 0,3 mm deeper than needed. After that:
Put the inlay into the scale with Epoxy. Until it gets hard you have some time.
Carefully punch the brass down so that it encloses the inlay perfectly. Even some wrapping around would be ok.
On the last step you sand again. This should work too.Edit:
@Grumpy. The shield inlay of modern knife can be extracted very easy. Just remove the scale and look from behind. There is a hole. Take a Victorinox cork screw and carefully press it out. Maybe a small knife will help too. My EDC Spartan is the perfect tool for it. ;) -
@HankSolon said:
@Grumpy. The shield inlay of modern knife can be extracted very easy. Just remove the scale and look from behind. There is a hole. Take a Victorinox cork screw and carefully press it out. Maybe a small knife will help too. My EDC Spartan is the perfect tool for it. ;)That's what I did, after finding the logo on the translucent sapphire scale popped out. Never had thought of pinning the entire outline first. Had cut into the wood but obviously not effectively enough. Tried to just cut the areas needed sunk-in but lost a bit of wood. Went ahead and carved out the entire area and epoxied the inlay inside.
Had used wood glue and the sawdust material. It clearly shows the repair, though dark grained wood might not show up as much. Wasn't wanting to mix sawdust with 6 minute epoxy. Will have to sand down with finer grit to polish the epoxied window more.
Also, when getting epoxy, look on the literature and make sure it is clear. Had went with a certain type of epoxy and found later it was a yellow tint.
-
looks good hank. what type of wood is that?
-
that inlay is flawless Hank.

-
Thanks for advice guys
brilliant as always

-
Just something I threw together this morning.
Urban Settler. 93mm clip point small blade in place of awl.


-
-
wow, the smurf filter had fun with that... what a concept

-
Yeoman Mechanic

-
Soon to be my first alox mod. Bought this 84mm electrician. Pivot hole is 2.5. Seems someone "made" an 84 and sold it to me. No worries. a little grinding and brass should fix this right up.

-
Exposed rivets are not fun.



-
A modern Golfer with Backtool (a hook). Syph, I hate you for your 84mm Golfer tutorial. ;)
I'm not happy with the snap of the scissor, but it works so far. I also will be more careful, shortening the scissor.
Next time I get some better drill bits. I wasted a cheap diamond bit, drilling a 2,2mm hole into the scissors. :)
However, a funny but very tough mod. Without my custom 600-1000 grit sanding paper for my proxxon It wouldn't have been that nice.


-
@HankSolon said:
A modern Golfer with Backtool (a hook). Syph, I hate you for your 84mm Golfer tutorial. ;)I'm not happy with the snap of the scissor, but it works so far. I also will be more careful, shortening the scissor.
Next time I get some better drill bits. I wasted a cheap diamond bit, drilling a 2,2mm hole into the scissors. :)
However, a funny but very tough mod. Without my custom 600-1000 grit sanding paper for my proxxon It wouldn't have been that nice.
Nice! Great work. Fun cutting down those scissors eh?
-
A Golfer with a hook..... I always had a slice

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

JR