Leatherman QC Fails
-
I've only fairly ['06 - ?] recently discovered LM. Always wanted one and the Surge was my first purchase. I've used it pretty hard and extensively and not had any problems with it at all. That is, other than the looseness of the lanyard/clip...which I'm told by LM is by design.
Really love the MUT EOD I got a few years ago. However, I'm on my second issue. I had sent the first one admittedly on something of a technicality -- the plier head didn't really meet for 'finer' work. You could see more than a bit of daylight with the pliers closed. The new model is much better in that regard. Ah, yes - but now I'm having slight issues with the plier head scraping against the body as you're opening & closing. That and the pliers jamming closed on me when wire cutting. So, I've tightened/re-tightened the torx screws...and I guess it's livable. I really don't want to send it in again and I suppose it could be that I've not got the right tension in tightening them there screws.
We'll see. I'm not much of a reference in terms of LM usership going back to early LM days. Having already committed to, though, the new Surge and Raptor...seriously hoping it's all good there - which I'm expecting it to be.
I really love LM as a company too - and on the flipside, I can say I've had absolutely no negative issues with the two OHTs that I bought. So, all is not lost, but I understand perfectly well what you all are saying: QC is everything.

-
Tell me what you think, am I going crazy?
-
Thats a bad pivot for sure. I bet the casting is malformed inside.
-
That's the same as all my Rebars, over a little bit if time and some oil, the pivot will loosen up and the binding with disappear. You basically have to squeeze it, then up stick it and do it again and again to smooth out the motion.
I notice that when I did the first transplant of the rebar head into a wave body.
-
I hope we are both unlucky and they are not all like that. Rebar is really growing on me for the compactness and weight.
I have already been through "a little bit of time" and lube. Actually I have gained 2 pounds in body muscle trying to work this thing loose.
The problem is thay it cannot be operated one handed. It's riddiculous that I have to drop whatever I'm holding with my other hand just to open the jaws....
Reviewers on YT don't seem to have that problem, anybody here with "good" rebar? -
If this turns out to be an inherent defect with the pivot on the Rebar pliers, all those who have replaced their Wave with Rebar pliers will be kicking themselves. There does seem to be a lot more stories of QC problems with Rebars than any other Leatherman tools.
-
My rebar pliers do not do that. I just tried and squeezed as hard as possible and they still open freely.
-
Maybe you're not strong enough.


-
What I can't understand is what exactly is wrong with this thing. It's basically a pin (rivet) trough a hole. No play o movement in the pivot, parts ot the pliers don't shift o move in other directions apart from rotating...
And actually you don't have to squeeze that hard for it to bind, just opening the tool is enough to make it stick...
-
-
Perhaps the pivot is not completely circular and does not fit completely flush within the pliers. Fortunately, the Rebar does not cost too much for you guys in the US. If I had paid £60 (US$90) for it here in the UK, I would not accept such a defect. People keep saying how wonderful the 25 year warranty is, but what they forget is that it cost us money to send the tools back each time. I would rather Leatherman focus on their quality, so we don't ever need to send them back.
-
After a little trial and error mine is smooth a silk. I couldn't be more pleased.


-
@hennypenny. I paid 54 pounds...
-
@BigMatt said:
@hennypenny. I paid 54 pounds...That is a lot of money for a Rebar, with defective pliers. My cheap £3 Stanley pliers sticks like you described, but you shouldn't accept this on a £54 tool.
-
My Rebar does the same thing with the pliers going tight , it's not as bad now as it was when I first got it.
Dunc
-
Wild. So we need a poll for rebar owners to figure out what % have sticking pliers.
-
"Hi there.
Just got my Rebar back.
Would you be so kind to have a quick look at this video? I'm not sure weather my description wasn't very good (it's quite unusuall problem), or it simply doesn't qualify.I would be gratefull for any thoughts. How much would it cost to replace the plier head outside of warranty? You have sorted me out so many times that I honestly have no problem paying for this repair.
I would be gratefull for any thoughts.Kind regards"
Email sent friday night so I would expect a reply on monday. I'll keep you posted.
-
Hi Matt
I have spoken to our technician about your tool. He does remember your particular tool due to the fact that he was off on the day it arrived. It was put to one side for him to look at as nothing wrong could be found with it. He also found no fault. We watched your video and the problem is that you would not normally clench the tool shut without anything in the pliers. When something is grasped it will not lock up. The Rebar is completely within Leatherman specifications therefore there is nothing we can do to improve it for you. I am sorry that you are not happy with your Leatherman but unfortunately we are unable to modify it.
Kind Regards,
Mary Lowe
Credit Control / Purchase LedgerDo I have to say that it makes no difference what is beeing grasped...
I don't know what to think. Response from cresit control? -
@BigMatt said:
... We watched your video and the problem is that you would not normally clench the tool shut without anything in the pliers. When something is grasped it will not lock up. ...That's garbage!
What about when gripping something thin like a thin sheet or sliver of metal?
What about when you've just used the cutters? That's exactly how the pliers will finish up!Sorry you're having a rough time with this, Matt. Is this Whitby & Co you're dealing with? They are usually very good in their service, so might be their terms of warranty as dictated by Portland are too tight on this occasion. If you have a Facebook account it might be worth popping a summary of this and your vid on Leatherman's page, or alternatively trying to get an email address for customer service in Portland.
Good luck, and keep us informed

-
Yes, Whitby.
The irony here is that they have sorted me so many times before, even when it was clearly user fault. But when the problem is actual "out of the box" issue...
Maybe they don't want to set a precedens and be forced to deal with any sticking pair of pliers. And the fact that I have been answered by above person...
I have been a bit of a pain in the last month sending them my surge twice (another story) and this rebar, not to mention a ton of emails.Anyway, I have emailed leatherman US with above link, we will see.
I bought it with the purpose of keeping it in my outdoor kit, but it gree on me and it keep landing in my pocket because its weight/capabilities ratio. BUT IT'S SUCH A PAIN TO USE...Can any of the moderators move this thread to a separate one or something? I didn't expect this thing to develope like that and hijack the topic. Thank you
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login