Rebar Mod
-
Hi everyone, i relly like the rebar and i was thinkig to buy one. but i don't like the position of the tools, especially the blade. I wanna ask you if it's possible to turn the plier and make the opening like the swisstool. I think if i mill a slot in the handle i can reverse the plier and make it fit in the handle in the closed position, also if i make a '' C '' whith a folded sheet of metal i can use it like a '' stop-pin'' for the plier's head , and aftrer this mod maybe it will work
<img src="http://imageshack.us/a/img823/3466/76xw.jpg" alt="Image Hosted by ImageShack.us"/><br/>
sorry for my bad english -
@DAMY said:
I wanna ask you if it's possible to turn the plier and make the opening like the swisstool.Not without MAJOR alteration! Open up the Rebar and notice how the pliers tips sit on top of the other tools. Even if you managed to get the handles to mount the other way round, the plier head would be "fighting" the other tools in the handles. You also risk making the handles a lot weaker with the cut outs. If you want a Rebar sized tool that's like the Swisstool, it would be far easier to get a Spirit ;) :D
(The Spirit S model would be the closest in terms of tool set)That said, don't let me put you off if this is something you want to play with ... just make sure you keep us informed at all stages, and don't forget the piccies
:D :D -
i don't have the rebar to take the right measurement, i wanna buy them if this mod can be done. i don't wanna take the spirit for the difficult to mod it and little other things. but if i can't mod the rebar maybe i can think to buy a spirit
-
I just looked at my Rebar and I would say that structurally this can't be done. The plier head extends past the tool locking mechanism and back spring for the mechanism on the handle (just past the 3mm mark on the ruler). Also, the awl and two flat drivers on one side and phillips on the other would hinder the plier head in the closed position. I would say get a Swiss Tool or even a Wave, Charge or Surge depending on what outside tools you need.
-
thank you for the answer. but if the plier touch the back spring for 2mm o 3mm i can grind the pliers to fit without compromise the lock. Maybe if i lift up a little the flat drivers the head can stay in the closed position
-
There is no way to do this.
The aperture where the rebar head sits in the handle is tuned for the pivot area's thickness. Having taken apart a few Spirits with the same tab tensioner, the handle's thickness accounts for the additional material that the sandwiched tab tensioner takes up.
Unless you start making new handle frames, its not a simple matter of cutting and putting in a part. Prying the handle distance will misalign the pivot holes too.
If you get this going, however, I tip my hat to you. I defer to better plier head locking designs than the Leatherman ones (ironically since I prefer LM over most companies)
-
It would be an interesting mod, but for sure you'd need to start with making a new frame. Vic ones also have the lock release on the side, if you stuck with the LM one, it would be on the inside and awkward to release a tool lock when closed. Outside opening tools is one of the reason I prefer Vic MTs.
-
ok, thank you for the answers, now i have to take a wave or a spirit

-
.... or both ....

:D
-
maybe :D
-
If you want outside opening tools why not buy a Bear & Sons or a Spirit...
-
because the spirit is good for me , but i wanna have the plier with the wire cutters removable and a hole for a cord for don't loose my multitool.
-
The new Surge has everything you are asking for.
-
Anything is possible including this. This is the whole purpose of MTO. What's the motto again? Anyone? So now I say stop saying no and let's all work together for a solution instead of falling into the "no it can't be done forum" after all it's what we do :)
-
@tattoosteve99 said:
Anything is possible including this. This is the whole purpose of MTO. What's the motto again? Anyone? So now I say stop saying no and let's all work together for a solution instead of falling into the "no it can't be done forum" after all it's what we do :)That is why I recommended Bear & Sons, it's essentially just what he's after aside from the OHO.
-
Anything is possible including this. This is the whole purpose of MTO. What's the motto again? Anyone? So now I say stop saying no and let's all work together for a solution instead of falling into the "no it can't be done forum" after all it's what we do :)
That is why I recommended Bear & Sons, it's essentially just what he's after aside from the OHO.
Excellent idea! But does it have the replaceable cutters?
-
No it doesn't have those :-\
-
Wouldn´t it be easier to find a tool with the right configuration (butterfly opening, outside opening tools)
and then look for a plier head with replaceable cutters that can be convinced to work there?
Say Rebar head to bear and sons?
Swapping handle tools should be rather easy afterwards, maybe SOG tools fit or even the ones from the donor-rebar, given you do not find the Toolset given satisfying. -
i see the greber strata :D but for the review on the internet this multitool doesn't look very well made, and in italy to buy it i have to order from a famous site (A....n) and cost 100 euro (140 dollars ). if it not cost more than a wave i will try. Anyone have the Gerber Strata and can talk me about? :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login