Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Schrade ST1 variations

Scheduled Pinned Locked Moved General Tool Discussion
15 Posts 1 Posters 9.8k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Schrade ST1 variations
Schrade ST1 variations
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • J-sews Offline
    J-sews
    Admin Team
    Posts: 23,224
    J-sews Offline
    J-sews
    Admin Team
    wrote on last edited by
    Quote Reply

      The ST1 Tough Tool was produced in the USA from 1997 until Schrade shut down in 2004. There are a suprising number of variations in the tools considering the short time they were in production. We recently talked about it in this thread HERE. After buying and borrowing a number of different Tough Tools I've managed to identify these four variations here:

      JAWS:
      The original Series 1 tools had jaws produced by stamping six different pieces out from heavy gauge sheet metal then laminating them together with rivets. Fine and coarse serrations were then cut into this sandwich of jaw plates, no doubt an expensive operation. Wire cutter area was also cut after stamping. Note stylized SCHRADE logo and right-side-up USA logo.

      Series 2 tools appeared sometime before 2000 (based on a photograph in the 2000 Field & Stream ad) Jaws were still produced from six pieces riveted together, but the pieces had changed somewhat. Now the center sections were investment cast, while only the outer four plates were stamped steel. Serrations were still cut after assembly. Wire cutters however were cast in from the start, eliminating some cost. Note plain SCHRADE logo and upsidedown USA logo.

      The entire jaw was cast solid on the Series 3 tools. Somewhat humorously, fake rivet heads were also cast into the jaws. (even though they serve no function) Jaw serrations were also cast in instead of cut in afterwards. By eliminating the rivets and the "sandwich" construction, number of pieces for a complete plier head was reduced from ten down to only two. Plus no more labor involved in assembly, riveting, and cutting serrations. Cost savings must have been considerable.

      After Taylor Brands acquired the Schrade name, production of the ST1 was resumed in China. These Series 4 Tough Tools resemble the American made models in appearance only. Close examination makes it clear that none of the dies or tooling from the original plant is being used to manufacture today's tools. Jaws remain entirely cast, with heavy burrs on a number of inner surfaces. The SCHRADE logo is now cast in place. Also note the flush plier pivot.

      1 Reply Last reply
      • Leatherman123 Offline
        Leatherman123
        Posts: 6,568
        Leatherman123 Offline
        Leatherman123
        wrote on last edited by
        #1 Quote Reply

          Thanks a lot Bob, I always wondered about the variations! It's amazing how companies can go down hill to save a buck!

          1 Reply Last reply
          • Poncho65 Offline
            Poncho65
            Global Moderators
            Posts: 88,523
            Poncho65 Offline
            Poncho65
            Global Moderators
            wrote on last edited by
            #2 Quote Reply

              Yeah nice pics Bob the first 2 pics were definately best quality, while the l;ast you can visibly see is of much less quality. Sad to see such a nice tool degrade like that.

              1 Reply Last reply
              • Smitty44 Offline
                Smitty44
                Posts: 2,026
                Smitty44 Offline
                Smitty44
                wrote on last edited by
                #3 Quote Reply

                  If it don't say USA,stay away!!!

                  1 Reply Last reply
                  • Spoonrobot Offline
                    Spoonrobot
                    Posts: 1,894
                    Spoonrobot Offline
                    Spoonrobot
                    wrote on last edited by
                    #4 Quote Reply

                      Excellent!

                      Thanks for taking the time and energy to put this together. I have a series 2 but will be on the lookout for other ones now that we have some more information on the subject.

                      You washed your hands after handling the series 4, right? :P

                      1 Reply Last reply
                      • J-sews Offline
                        J-sews
                        Admin Team
                        Posts: 23,224
                        J-sews Offline
                        J-sews
                        Admin Team
                        wrote on last edited by
                        #5 Quote Reply

                          @Spoonrobot said:
                          Excellent!

                          Thanks for taking the time and energy to put this together. I have a series 2 but will be on the lookout for other ones now that we have some more information on the subject.

                          You washed your hands after handling the series 4, right? :P

                          Washed AND disinfected! :P

                          This Chinese version is sooooo bad. The sheet metal on the left handle is warped and distorted. Two of the knife blades don't fold into it properly. Chinese solution? Simply bend the tips of the blades over until they do fit. ::)

                          1 Reply Last reply
                          • Grant Lamontagne Offline
                            Grant Lamontagne
                            administrators
                            Posts: 67,980
                            Grant Lamontagne Offline
                            Grant Lamontagne
                            administrators
                            wrote on last edited by
                            #6 Quote Reply

                              Wow- it actually hurts to look at that!

                              Have you identified any other generational differences between the various incarnations? It might be interesting to see the other goodies- it's obvious quality went downhill after Schrade went out of business, but how is the Gen 3 quality overall? Do you think the difference between cast heads and laminated heads changes the quality any? The change makes sense if there's no appreciable loss of quality/strength but it's cheaper to manufacture.

                              Def


                              1 Reply Last reply
                              • Mike, Lord of the Spammers! Offline
                                Mike, Lord of the Spammers!
                                Posts: 42,975
                                Mike, Lord of the Spammers! Offline
                                Mike, Lord of the Spammers!
                                wrote on last edited by
                                #7 Quote Reply

                                  That really is awful >:(

                                  1 Reply Last reply
                                  • Benner Offline
                                    Benner
                                    Posts: 28,081
                                    Benner Offline
                                    Benner
                                    wrote on last edited by
                                    #8 Quote Reply

                                      Thanks for that Bob, it was very interesting. :)

                                      That chinese one is shockingly awful isn't it. :-\

                                      1 Reply Last reply
                                      • Leatherman123 Offline
                                        Leatherman123
                                        Posts: 6,568
                                        Leatherman123 Offline
                                        Leatherman123
                                        wrote on last edited by
                                        #9 Quote Reply

                                          It really is a POS! Bob, how much did you pay for it?/! I saw a Chinese made one at Kmart yesterday.. It didn't look AS bad as yours though! ???

                                          1 Reply Last reply
                                          • J-sews Offline
                                            J-sews
                                            Admin Team
                                            Posts: 23,224
                                            J-sews Offline
                                            J-sews
                                            Admin Team
                                            wrote on last edited by
                                            #10 Quote Reply

                                              @Leatherman123 said:
                                              It really is a POS! Bob, how much did you pay for it?/! I saw a Chinese made one at Kmart yesterday.. It didn't look AS bad as yours though! ???

                                              They don't look that bad, but trust me, they are. I'm embarrassed to admit that I paid $14 for this one. :-[

                                              1 Reply Last reply
                                              • J-sews Offline
                                                J-sews
                                                Admin Team
                                                Posts: 23,224
                                                J-sews Offline
                                                J-sews
                                                Admin Team
                                                wrote on last edited by J-sews
                                                #11 Quote Reply

                                                  @Defender said:
                                                  ........it's obvious quality went downhill after Schrade went out of business, but how is the Gen 3 quality overall? Do you think the difference between cast heads and laminated heads changes the quality any? The change makes sense if there's no appreciable loss of quality/strength but it's cheaper to manufacture.

                                                  Def

                                                  Oops, guess I should clarify. In my opinion, the overall quality of Series 1 thru 3 made in USA tools are all quite good. Changing from labor-intensive laminated plier jaws to investment cast ones did not take away anything from the tool. If anything it made the ST1 more comparable to multitools from Leatherman and Gerber and everyone else who ALWAYS used cast plier heads.

                                                  @Defender said:
                                                  ......Have you identified any other generational differences between the various incarnations?.....

                                                  As a matter of fact there is an entire Encyclopedia page devoted to just that topic: https://wiki.multitool.org/tiki-index.php?page=ST1+Tough+Tool+variations

                                                  Does anyone have an ST1 model with features other than what is listed?

                                                  1 Reply Last reply
                                                  • Grant Lamontagne Offline
                                                    Grant Lamontagne
                                                    administrators
                                                    Posts: 67,980
                                                    Grant Lamontagne Offline
                                                    Grant Lamontagne
                                                    administrators
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      It looks like mine is a second generation model:

                                                      http://www.multitool.org/miscellaneous-tools/large-tools/schrade-st1.html

                                                      I'll have a closer look and let you know if there are any other variations on mine, but mine has seen better days so if they are subtle, they may not be visible.

                                                      Def


                                                      1 Reply Last reply
                                                      • tango44 Offline
                                                        tango44
                                                        Posts: 452
                                                        tango44 Offline
                                                        tango44
                                                        wrote on last edited by
                                                        #13 Quote Reply

                                                          If anybody is interested if have one T1 Tough Tool series 3 for trade, is used but not abused.
                                                          I'm looking for a Black Oxide CORE or SWISSTOOL.
                                                          PM me or drop me a line to jfcm44@hotmail.com

                                                          Thanks.

                                                          1 Reply Last reply
                                                          • Mike, Lord of the Spammers! Offline
                                                            Mike, Lord of the Spammers!
                                                            Posts: 42,975
                                                            Mike, Lord of the Spammers! Offline
                                                            Mike, Lord of the Spammers!
                                                            wrote on last edited by
                                                            #14 Quote Reply

                                                              @J-sews said:

                                                              @Leatherman123 said:

                                                              It really is a POS! Bob, how much did you pay for it?/! I saw a Chinese made one at Kmart yesterday.. It didn't look AS bad as yours though! ???

                                                              They don't look that bad, but trust me, they are. I'm embarrassed to admit that I paid $14 for this one. :-[

                                                              At least you've SAVED a few of us $14 mate :)

                                                              1 Reply Last reply

                                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                              With your input, this post could be even better 💗

                                                              Register Login

                                                              1. Home
                                                              2. Tool Talk
                                                              3. General Tool Discussion
                                                              4. Schrade ST1 variations
                                                              Reply
                                                              • Reply as topic
                                                              Log in to reply
                                                              COMMUNITY LINKS
                                                              EDC-TV SAKWiki GearFeed SAKSelector
                                                              Operational Funds

                                                              Help us keep the Unworkable working!

                                                              Make A Donation
                                                              November Goal: $300.00
                                                              Due Date: Nov 30
                                                              Total Receipts: $0.00
                                                              Below Goal: $300.00
                                                              0% funded
                                                              • Login

                                                              • Don't have an account? Register

                                                              • Login or register to search.
                                                              • First post
                                                                Last post
                                                              0