Cordless drills, brushless?
-
Make mine brushless , less to go wrong , a bit shorter in overall length , better run time on batt's , longer service life on tools . Lots of nice new toys comming out . Milwaukee has some new product , that if I hadn't tried , I wouldn't believe .
The thing thats screwing me up now , is that I'm using two Metabo chargers , one Hilti charger , a Milwaukee M12 , and an M18 . Basically , I have a milk crate filled with nothing but batts. and chargers . Lest we forget the , charger for the paslode nail guns .
To make matters worse , I want a Festool C12 , their 15 V. impact , and the new cordless Carvex Jigsaw . I also have a jones for the new Senco cordless nailers ( no more stinky fuel , and no ramp up time )
Chris
-
Yeah the brushless are kinda expensive right now, just a drill alone cost way more than what I paid for the kit. I figure by the time batteries die on this, they should come down in price and I'll switch over.
-
Tried them out today, very impressive. While the drill certainly has enough torque to drive 3.5" screws (biggest I have) all the way into wood and take them out again, bit slippage is a problem (and will strip both bit and screw fast). The impact driver however will hammer them in or out pretty effortlessly, no rotational strain on wrist as well. It it LOUD though, ear plugs highly recommended.

-
@jzmtl said:
Tried them out today, very impressive. While the drill certainly has enough torque to drive 3.5" screws (biggest I have) all the way into wood and take them out again, bit slippage is a problem (and will strip both bit and screw fast). The impact driver however will hammer them in or out pretty effortlessly, no rotational strain on wrist as well. It it LOUD though, ear plugs highly recommended.
nice! and congrats for the new tools
yeah impact/hammer is pretty loud, people will know your working lol -
I did learn something interesting, the impact driver would make a better hammer drill than an actual hammer drill, just need a chuck adapter. A regular hammer drill works by rubbing two ribbed plate against each other, whereas a impact driver actually have a hammer hits the anvil producing both forward and rotational force, sorta like a rotary hammer.
On a similar note, a impact WRENCH wouldn't make a good impact DRIVER even though there are lots of adapters, because the way the hammers are arranged it produce rotational force only, no forward force which is what prevents cam out.
Haven't actually tested it though so this is mostly theoretical, need to procure a chuck with 1/4" hex shaft first which I don't have a source yet.
-
I think you may have misunderstood something.
The impact driver works in the same way as an impact wrench, it's a round and round motion only. There isn't any in and out motion. With a suitable 1/4" chuck or 1/4" shanked drill bits you can drill holes but don't put so much on that it starts impacting or you can end up screwing the bit in to the thing you're trying to drill / shatter the bit.
An impact drill uses the round and round motion to create the in and out impacts. SDS drills have separate "round and round" and "in and out" mechanisms so you can have the in and out without the round and round.
-
I find the hammer drill action works well with concrete. I haven't tried it on wood or steel yet, not sure I see the point of hammering a drill bit into a steel hole. For metal, getting that nice ribbon running is what I'm after.
-
The internal hammers aren't the same between impact driver and wrench. Take a look at this video, notice how the hammer on this impact driver attachment slam forward while rotating at the same time, so even though the chuck doesn't move like a hammer drill the impact force is there.
Whereas impact wrench's hammer doesn't have the forward/back movement, which you can see on bottom of this page.
I don't have a internal pic of rotary hammer yet, but I think it works more like a spring airgun in transferring the forward force.
@Mr. Whippy said:
I find the hammer drill action works well with concrete. I haven't tried it on wood or steel yet, not sure I see the point of hammering a drill bit into a steel hole. For metal, getting that nice ribbon running is what I'm after.It makes a lot of noise and makes your hands numb... First hand experience when I forgot to turn off the hammer feature. :-[
-
That explains why using a non-collared bit in an impact driver gets horribly jammed in it. DAMHIK

-
People say put some grease in there keep the bit from jamming, haven't tried it myself.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
