What did you use your Leatherman for today?
-
Welcome edcmultitool! glad you found this place! welcome, and enjoy your stay

-
Thank you for the welcome,
I use the large flat blade for prying a lot. Seem to hold up well.

-
Very 8) Welcome to MT.O!¡!
-
Haven't put her to use yet but have been fondling the Rebar quite a bit. :D

-
Replacing the compressor start relay on a refrigerator.

-
Used the can opener this morning to dig out some old seals on a sink handle drain on a large commercial sink so I could replace them with new ones.
I have tried to count the number of times I use my MT in a day, but I always lose count before the day is over, lol...
-
@edcmultitool said:
Used the can opener this morning to dig out some old seals on a sink handle drain on a large commercial sink so I could replace them with new ones.I have tried to count the number of times I use my MT in a day, but I always lose count before the day is over, lol...
Well if you take a picture every time, it will be easier to count them all at the end of the day. You might have to work overtime though.
But you'll also have great pics for this thread. 
-
I opened the packaging of my new OHT with my Wave.

-
New member, quick update :)
Wave: On vacation after quite a few years EDC.

Skeletool: Opening boxes at work, opening a drink at a Halloween party.
Supertool 300: Bending wire handles for my wife's cooking basket, carving a pumpkin with the saw and awl, removing air filter from my truck, opening a can of beans, removing the foil from an antifreeze bottle, scraping weld slag with the pliers.
Crunch: Removing battery cables on my truck, assembling some tooling fixtures, holding a tooling component while grinding, stripping some wires, fixing my wife's apple-coring machine (had to hold a small, bendable part with the Crunch, and hold the Crunch in a vise to do some precision dremel work) and of course, practicing one-hand deployment/retraction!

-
Almost forgot the tool-on-tool tales:
Used Supertool 300 pliers to bend Crunch lower-jaw friction-fit pivot so the Crunch wouldn't "fall apart" as easily when released.
After the pumpkin carving party, my new Supertool 300 developed a loose pivot from all the pumpkin guts. Used Crunch pliers/pin vise to tighten Supertool pivot back to the sweet spot.
-
Just used the mini screwdriver on my Wave to tighten my eyeglasses and sunglasses, and also to pry the scales off of one of my Swiss Army Knives.
-
Retightened the rear brake cable on my bike (note to self: order the bit extender for easier access :D)
-
At least 3 times a week I use a Leatherman to cut strings off of clothing...i'm a stickler for cutting strings off clothing.
-
Used my Rebar for some Phillips screws.
-
Opened some boxes and bags at work this morning with the Skeletool. The boxes were stapled underneath the tape
Skeletool pliers used to remove heavy staples.Used the Supertool 300 today to clean a neglected weld gun nozzle, trim weld wire and chip/file a welded assembly.
Used the Crunch to hold together a few pieces of steel for welding. Got some weld berries on the Crunch. Used Supertool file to clean Crunch!
-
We had a ton of boxes to open for new inventory at the shop today. Mostly new decanter and glasses sets. A couple boxes had cigars in them but not as many as I would have liked to see. Used the heck out of my Juice Pro, Oppie 8 & Wenger Zino this evening.
-
It's 8:00am in the morning!

-
-
It's 8:00am in the morning!

No it's 0900.
Sent from my iPhone 5 using Tapatalk
In Ontario it's 8:04.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login