Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

What next?

Scheduled Pinned Locked Moved General Tool Discussion
26 Posts 1 Posters 2.8k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. What next?
What next?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Cupboard Offline
    Cupboard
    Posts: 2,018
    Cupboard Offline
    Cupboard
    wrote on last edited by
    #20 Quote Reply

      @Monrogue said:
      I have one and it is a great tool, regardless of the flaws Cupboard mentioned (even though they are valid ones, depending on your usage).

      I have one, and it's a great tool regardless of the flaws that I mentioned. But I'm always going to play Devil's advocate and point out the flaws in something when someone's trying to make an informed decision about something.

      @Dem said:
      People don't like the Phillips driver on the Spirit? I think it's one of the best I've seen in an MT, which is almost surprising since it works so well while still being polished.

      I really dislike the bit driver LM goes with now. Changing a doorknob with a bit-driver LM seems to fall into the category of either 'doing this sucks' or 'this isn't going to happen.'

      The Phillips driver is nice and long and fits reasonably well in screws (but not as good as the LM #2 Phillips bit I carry). The problems with it that I see is that despite having had less use and abuse than the Leatherman bits it's noticeably marked on the end. That's not affecting performance yet but it's a little concerning to me and given the same amount of use again (3 weeks which saw a lots of screwdrivering) I think it might be a proper problem. Still, I have put a lot of torque through it and it isn't tool steel so I can't hold it against it too much!

      That's not to say LM is perfect, it has its own faults but this isn't the time or place.

      1 Reply Last reply
      • Philthy Offline
        Philthy
        Posts: 266
        Philthy Offline
        Philthy
        wrote on last edited by
        #21 Quote Reply

          @Cupboard said:
          Except the wire cutters are crap, it doesn't have a OHO blade, its Phillips driver isn't as good as the Leatherman's, the file isn't as good as the Wave/Charge/Surge... etc

          It's good, but it's not the best. Still, I'd go for it over the Powerlock. It's smaller and light than the SOG too isn't it?

          I could forgive the Spirit all its other faults if it wasn't for the wire cutters' inability to cut most of the stranded wire I frequently cut with my Wave.

          I'm going to have to disagree with you on the Swisstool's Phillips vs a Wave Phillips. The Swisstool's driver has decent length to it and I find that there are often situations where I need a driver with some length. The Waver driver is way to short, it's great that you can change the bits but all of the bits are short.

          1 Reply Last reply
          • ducttapetech Offline
            ducttapetech
            Posts: 18,707
            ducttapetech Offline
            ducttapetech
            wrote on last edited by
            #22 Quote Reply

              Some of the bits come in long too.

              uploadfromtaptalk1382744075034.jpg

              1 Reply Last reply
              • Cupboard Offline
                Cupboard
                Posts: 2,018
                Cupboard Offline
                Cupboard
                wrote on last edited by
                #23 Quote Reply

                  Exactly - I've removed the saw which gives a nice slot to hold the long bit. Horses for courses - I never used the saw and I use the driver a lot.

                  There's a good bit of thread derailment right there!

                  In my previous posts, please read Powerlock as Powerassist ::)

                  1 Reply Last reply
                  • ? This user is from outside of this forum
                    Guest
                    Posts:
                    ? This user is from outside of this forum
                    Guest
                    wrote on last edited by
                    #24 Quote Reply

                      @Cupboard said:
                      Except the wire cutters are crap, it doesn't have a OHO blade, its Phillips driver isn't as good as the Leatherman's, the file isn't as good as the Wave/Charge/Surge... etc

                      It's good, but it's not the best. Still, I'd go for it over the Powerlock. It's smaller and light than the SOG too isn't it?

                      I could forgive the Spirit all its other faults if it wasn't for the wire cutters' inability to cut most of the stranded wire I frequently cut with my Wave.

                      Not that your opinion isn't valid, but I don't understand this statement. My first Spirit was a very well worn example and I can remember trying it with stranded wire using the forward soft wire notch. It cut the stranded wire easily :think: My new Swisstool also cuts stranded wire easily, using the forward notch. On the other hand, I had a Wave which didn't make a brilliant job with this type of wire. The Wave in question had a minute amount of play in the plier head. Go figure :)

                      1 Reply Last reply
                      • Cupboard Offline
                        Cupboard
                        Posts: 2,018
                        Cupboard Offline
                        Cupboard
                        wrote on last edited by Cupboard
                        #25 Quote Reply

                          back in 5 minutes, just going to raid some cable from work ;)

                          Edit: I think I'm going to add this to the stranded wire test, it's going to be a bit huge. The first test on some 0.2mm 1000V cable was that the Juice, Wave, Rebar, Skeletool, Wingman and Squirt all passed, Dime and Spirit failed. My Spirit is in better condition than the comparable Leathermans.

                          Link: http://forum.multitool.org/general-tool-discussion/stranded-wire-cut-off-test/msg793123/#msg793123

                          1 Reply Last reply

                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                          With your input, this post could be even better 💗

                          Register Login

                          1. Home
                          2. Tool Talk
                          3. General Tool Discussion
                          4. What next?
                          Reply
                          • Reply as topic
                          Log in to reply
                          COMMUNITY LINKS
                          EDC-TV SAKWiki GearFeed SAKSelector
                          Operational Funds

                          Help us keep the Unworkable working!

                          Make A Donation
                          November Goal: $300.00
                          Due Date: Nov 30
                          Total Receipts: $0.00
                          Below Goal: $300.00
                          0% funded
                          • Login

                          • Don't have an account? Register

                          • Login or register to search.
                          • First post
                            Last post
                          0