The 30-Day Rebar Challenge!
-
-
Day 12 was full of hard jobs that were not at all urgent, and easy jobs more urgent than escaping from a room full of angry house cats.
The first job wasn't theatre related at all. I found a broken discman in a box whilst unpacking, and started playing with it. It wasn't working, so I used the fine driver to open the unit up. The larger screws were no problem, but the tinny ones on the inside needed a very fine driver (I stole the one from my Evo 17). I'm not sure why—I'm a lot better with analogue technologies than digital ones. Anyway, after taking the whole thing apart and putting it back together, I finally realized that it was the CD spindle that was broken, so rather than a Leatherman Rebar I needed boring, useful ol' superglue. Lesson learned: check the external stuff before going ape nuts with a screwdriver!
So Val is good for normal electronics screws, but not little tiny ones. That's pretty common with multitools, but it is too bad.
Back at the theatre, I had to trim a coroplast flat to keep it flush with the next flat over. I used Val, and then for the first time needed to give the blade a quick sharpening with a ceramic rod. Now it's good as new!
I has to tighten two wheel casters, which were both Robertson screws. I managed to get a decent grip on the screw heads with the pliers by sticking one tine in the hole and pinching hard. Nice job, Val!
I also had to tighten an eye bolt, so I use the small screwdriver as a lever, and spun the bolt. It was tough going, but it worked, and no damage!
The easiest but most frightening issue was with my costume—someone tied the drawstring at the neck with that experts call a Dorkbag Hitch. I had about 30 seconds to get it undone so I could fit the shirt over my giant monster of a head, but nothing doing. It was permanaknotted. This is exactly why I always make sure to know where the nearest knife is. It's also a good thing I had sharpened the blade maybe an hour earlier, because two quick slices and I made it onstage just in time, albeit short one drawstring.
Whew! Thanks, Val, for saving the day on Day 12!
-
@Jothra said:
Now, I know I'll misuse my tools if it means getting a job done faster, but even I cringe when I hear that they used the main blade to open cans of house paint. Aargh! Shockingly, no damage!Finally some abuse

I would have to be 30 flavours of desperate before I'd start opening paint cans with the knife blade of a tool with a prybar in it.
-
@Jothra said:
Now, I know I'll misuse my tools if it means getting a job done faster, but even I cringe when I hear that they used the main blade to open cans of house paint. Aargh! Shockingly, no damage!Finally some abuse

I would have to be 30 flavours of desperate before I'd start opening paint cans with the knife blade of a tool with a prybar in it.
+1
There's abuse and then there's stupid abuse >:(
-
Now, you wouldn't think I would have to spend so much time fixing beds, but that's theatre for you.
On Day 13, the metal headboards on two of the beds on-set were starting to get really loose, and it turns out haphazardly installed tie wire was the culprit. Fortunately, Leatherman pliers are fantastic at tying wire.

Just let me adjust that tie for you...Step 1 was to get rid of the old wire. This was actually easier to break than untie, so Val did some bustin' up. Step 2 was making sure the frames were at the right height to keep them from dragging on the floor (pictured in the...pic...ture. Good sentence there...) Third was to wrap twice on each side with doubled-up wire, since a single wrap per side would let the frame rock like mad, and doubled-up wire is, naturally, stronger. Now, in theory a saddle or butterfly tie would work best, but I cheated and ran the wire through the bolt holes on the frames, so it should be good to go.
The Rebar pliers flex a lot less than the Wave ones when twisting wire, especially when the wire is doubled up. I often grab wire with the sides of the plier jaws instead of the tips because I'm afraid they'll snap off, but with the Rebar I didn't bother. They are, as bicycle periodicals are so fond of saying, horizontally stiff and vertically compliant. I like. I like yes much.
Day 13!
-
Two Day 12s! :ahhh :ahhh :ahhh
-
Given he's already said he fell asleep on his keyboard doing one of the updates, I think that can be forgiven :)
I get the impression that using the Rebar isn't all that much of a challenge, it's doing too good a job >:D
-
@CanadianLMfan said:
Two Day 12s! :ahhh :ahhh :ahhhFunny I didn't get the "someone has posted" warning when I posted the edit. There was almost a third Day 12. Just one of those things, I guess.
The Rebar is performing very well. I'm not kidding when I say the plier jaws are less of a concern than the Wave or Kick ones. I managed to snap a Kick tip once. I don't think I'm worried about doing it to the Rebar.
-
Two Day 12s! :ahhh :ahhh :ahhh
Funny I didn't get the "someone has posted" warning when I posted the edit. There was almost a third Day 12. Just one of those things, I guess.
The Rebar is performing very well. I'm not kidding when I say the plier jaws are less of a concern than the Wave or Kick ones. I managed to snap a Kick tip once. I don't think I'm worried about doing it to the Rebar.
You said five updates but there were only 4.

-
edit: nothing to see here

-
You know, don't take this the wrong way, but Val is a cheap woman. [Currently US$35.16 shipped on eBay.] Is she the kind of girl with which one should have a long-term relationship, or do you maybe just use her for a while and then move on to something better? I guess this thread will help answer that question.
-
@powernoodle said:
You know, don't take this the wrong way, but Val is a cheap woman. [Currently US$35.16 shipped on eBay.] Is she the kind of girl with which one should have a long-term relationship, or do you maybe just use her for a while and then move on to something better? I guess this thread will help answer that question.Don't confuse a cheap date with a cheap woman. Sometimes all you're hungry for is a carnival hot dog.
Anyway, Day 14 (I know there were two Day 12s, but we'll go ahead and pretend I'm not a dingus) was matinee day! It was still daylight when I left the theatre!
The first thing I did was put a notch in a crappy Halloween-grade arrow, so a Lost Boy could fire it a little more forcefully into the wings of the stage (because nothing is as dumb looking as firing an arrow a foot and a half, bending over to pick it up, and firing it again). A friend was going to use the blade, but I suggested the saw. It did the trick. I like the saw, but the angled teeth make it more useful pulling than pushing. Yes, this makes it more aggressive, but on the other hand it's not as versatile. Versatile is a word I throw around a lot, and I mean it, too. Again, though, it did get the job done, and remains nice and sharp.
One of the hinged 2x4 "brakes" that holds the casters of our Neverland set up or lets them down got nicely jammed in the "wheels down" position. Oh, how I wish electronics didn't mess with our microphones, because I would love to have a picture of what we ended up doing: two guys held up the corner, while I bonked the hinge pin out with Val's small screwdriver (not locked—it was out at a jaunty angle to fit) and a hammer. Once the pin was up far enough, we wiggled it free with the pliers.
As far as I can tell there isn't any damage to the locking mechanism, which took the brunt of the hammering, but I'll keep an eye out and let you know as I keep using the tool.
Now I have two dark days on the play, but that just means more work I've been neglecting around my apartment. Until then, this was Day 14!
-
Don't you mean Day 15?

-
can you put your phone on to aeroplane mode? That will stop the annoying "derp de der derp de der derp derp" noise.
-
@Cupboard said:
can you put your phone on to aeroplane mode? That will stop the annoying "derp de der derp de der derp derp" noise.Even LCD screens can screw with our microphones. No fooling. Electronics are forbidden onstage.
Usually this is a great rule, but no-one ever thought to write in an exception for people doing multitool testing.
-
:ahhh
Not denying your mics have issues, but I've happily run all the effects for a show off a laptop sat on top of a couple of racks of radio mics!
Still, it make everyone's life better and easier with a blanket ban.
-
Really, the theatre group just needs to invest in some halfway modern shielded sound equipment. After all, every light in the show is controlled from an iPad. I'm surprised they aren't having trouble with that, too.
-
This is an excellent review so far.
-
Report cards, two and a half hours of driving a day, acting, and backstage work add up to literally no time sitting at a computer for days! Believe me--I'm not misusing the word "literally", either.
All missing updates will arrive sometime between 1 and 3 (MST) this afternoon!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


>:D