Never thought I'd see it, tire falling off on highway
-
-
Gareth. Yes, that's what I was talking about.Still worried by this thread's content, though. :D
-
I wouldn't be that concerned about it if I were you. These are the kinds of things that happen every day in most major cities. If anything, being more aware of it now makes you that much safer than before.
Def
-
Well, I'm only a little concerned, but it's funny this thread should show up two weeks after I was talking to the guy about this exact thing ! He explained to me that there are going to be plenty of warning signs such as a rattling sound early enough and that the tire will probably fall off while slowing down.
Actually, it's just knowing my luck that worries me most :D
-
....
Actually, it's just knowing my luck that worries me most :DSo without bad luck, you'd have no luck at all?? :D
I'm not saying I only have bad luck, far from it so far, thankfully.
It's just a feeling I get at times, that my luck has a really twisted sense of humour, that's all.
::)
-
How many people actually have a torque wrench and check the torque on their wheels properly?
I have access to one but most of the time I'm lazy and just do them to approximately one Tom on the end of a spanner tight. That way I know I'll be able to undo them again if needed. Once I've gone round them all I'll put most of my tools away and check them again.If I've had my tyres changed by someone and I haven't watched them put the wheels back on I'll take my car into the workshop, remove all the nuts and re-seat them by hand. When I bought Bertie the Bus the nuts had been done up so tight our little 650NM air gun had to have quite a rattle before it took them off, very glad I did it in the workshop before actually needing to do them in anger by hand.
I've been in a situation where I've needed a bit of scaff pole on the wrench to undo wheel nuts, thankfully I did have a bit of scaff pole but since then where possible I've checked them.
-
@Cupboard said:
How many people actually have a torque wrench and check the torque on their wheels properly?
I have access to one but most of the time I'm lazy and just do them to approximately one Tom on the end of a spanner tight. That way I know I'll be able to undo them again if needed. Once I've gone round them all I'll put most of my tools away and check them again.If I've had my tyres changed by someone and I haven't watched them put the wheels back on I'll take my car into the workshop, remove all the nuts and re-seat them by hand. When I bought Bertie the Bus the nuts had been done up so tight our little 650NM air gun had to have quite a rattle before it took them off, very glad I did it in the workshop before actually needing to do them in anger by hand.
I've been in a situation where I've needed a bit of scaff pole on the wrench to undo wheel nuts, thankfully I did have a bit of scaff pole but since then where possible I've checked them.
I have a 1/2" torque wrench, but I've never used it changing tires. I tighten them a little at a time, doing every second nut until they are nice and snug. One thing I won't use putting them on is my impact. This is one thing I'd much rather tighten by hand!
-
One thing I won't use putting them on is my impact. This is one thing I'd much rather tighten by hand!
I use impact to spin them on after do the first turn or two by hand, but not tighten them, saves a lot of manual cranking.
Yeah, I used to use my battery powered impact to start them, then tighten them by hand, that is until the charger kicked the bucket.
Sent from my iPhone 5 using Tapatalk
-
I got a Canadian Tire impact wrench that doesn't have a torque setting on it. I actually rarely ever use it. I have a crossbar tire iron and usually I just hold one end and use the side handles to spin it. I don't even own a torque wrench so I have no idea if I'm doing it properly or not. The good news is I haven't lost a tire in a very long time.
Def
Sent from a digital multitool
-
I don't think any of them has torque setting. I used to do tire change with a long handle ratchet too but it's heck a lot less work with impact wrench.
-
Yes, I'll take up the slack with an air gun/impact wrench but won't do them up right tight with it.
One of ours does have different torque settings but I have no idea what it actually changes. If anything you're choosing between "lots" and "more lots" which isn't really appropriate or useful.With my battery one the torque is just set by how long you let it rattle for and it really depends on what you're doing up. Bolting two hard things together will get to maximum torque very quickly but with two soft things the more you rattle the more you just pull the fastener together through the thing you're trying to fasten.
They're extremely useful for taking things apart though

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
:D