Gerbers are C-R-A-P !!!!!!! (A warning for Flik fans)
-
@Spoonrobot said:
......Then again, I'm fairly lucky. ;)This coming from the guy who Fragged his Charge..... ::) :D

-
......Then again, I'm fairly lucky. ;)
This coming from the guy who Fragged his Charge..... ::) :D

I've not seen this pic before , so thats another bust charge then .
Dunc
-
@Benner said:
It's a shame to see ALL of Gerbers products rubbished again down to another breakage. :( All tools can break and every brand has the odd dodgy tool every now and then, but I don't think Gerber should be intantly ruled out because of it.I'm with Roadie on this one, Gerber DO make some good tools. :)
Your right and I agree with you but I'm still glad I chose a Spirit over the Flick ( I came so close to getting one ) .
Dunc
-
It's a shame to see ALL of Gerbers products rubbished again down to another breakage. :( All tools can break and every brand has the odd dodgy tool every now and then, but I don't think Gerber should be intantly ruled out because of it.
I'm with Roadie on this one, Gerber DO make some good tools. :)
Your right and I agree with you but I'm still glad I chose a Spirit over the Flick ( I came so close to getting one ) .
Dunc
TBH, I would (and will) do exactly the same thing, but that isn't because I have been put off of Gerber because they are apparently all "crap".
-
Yes, but not only did I not get dinged in the eye but I was able to find both pieces of the bit driver. A miracle considering how random their flight pattern was. ;)
so thats another bust charge then .
Pfft. I think it was the first reported Charge bit driver bust.
-
@Spoonrobot said:
Yes, but not only did I not get dinged in the eye but I was able to find both pieces of the bit driver. A miracle considering how random their flight pattern was. ;)so thats another bust charge then .
Pfft. I think it was the first reported Charge bit driver bust.
So there have been more since then ;) and of course the springs flying off the holder .
Dunc
-
Sorry to hear about your bad luck with the Flik- and after you were so fond of it originally! I can see why you'd be disappointed.
I have to say, I was somewhat concerned about that with my Flik when I got it, and so I purposely gripped it as hard as I could in hopes of breaking it, and nothing happened. Yours may have been from an earlier run, a defective model, or your friend has much stronger hands than I do, because I didn't feel any weakness at all, let alone a catastrophic one like yours.
My suggestion is, get a replacement from Gerber (Fiskars) and trade it to someone else here for something you would like. It's unfortunate, but I seriously doubt Gerber will refund your money on it- warranties are designed so the companies don't have to put out any actual cash.
I still like the Flik, and I'll continue to use mine for medium duty tasks, but I will keep this in mind every time it clears the sheath. This is also why I wrote what I did last week about the SwissTool RS- simple, well made designs are their own reward.
Def
-
I agree with you 100% Def!

-
@Leatherman123 said:
I agree with you 100% Def!
Where was that butt kissing smilie again? :P
Only joking. ;)
-
LOL!
:D -
I agree with you 100% Def!

Where was that butt kissing smilie again? :P
What this one

-
Just heard back from a Ms. Deb Sreiberg (Product Manager Outdoor Recreation, Fiskars Brands Canada Inc.)... on a Sunday evening, no less.
According to her, an early batch of Fliks bound for the Canadian market (specifically Canadian Tire) "did not meet [Gerber's] quality control standards" (her words). This was apparently an "isolated incident" (again, her words).
She offered to send me another Flik free of charge, plus some "additional products due to [my] unpleasant experience."
I'm not usually the type to "milk" a situation to my advantage, so I told her that a replacement would suffice. I'm only looking for some kind of fair settlement. I'm still not sure at this point whether I'll have to send my broken one back to them.
So... that's it. I honestly don't know what to make of her "isolated incident" explanation. It may very well be true, though I find it odd that only Fliks from Canadian Tire would be affected. (BTW Def, didn't you buy yours from CT also?)
At any rate, if and when I receive this "new" Flik, I'll very likely leave it unopened and put it up for auction. I'm plenty happy with my TTi. Besides, I could use the extra cash.
-
-
@J-sews said:
Well kudos to Gerber for getting back with you promptly. Got to hand it to them for that.At any rate, if and when I receive this "new" Flik, I'll very likely leave it unopened and put it up for auction.......
So you're not going to try the same squeeze thing on the second tool?
Once bitten, twice shy, baby! ;)
-
Well, I must admit, so far "crappy" Gerber seems to be on the ball when it comes to honoring their warranty.
Just got another response from Ms. Sreiberg about 15 minutes ago.
According to their head office in Portland, this was a known problem affecting Fliks destined for Canadian Tire upon their "initial launch" (i.e. very early models--although given how short a time this tool has been on the market, "very early" is a pretty relative term here). Only a small number of these tools were affected... and apparently, I was one of the unlucky ones who purchased one of the duds.
She insists that the Flik they intend to send me is of recent manufacture and "should be fine" (I'm sure its future owner will appreciate that :D ). She also insists on sending me a few additional compensatory items. Heh, who am I to argue :P ... Hey! Maybe they'll send me a BO Diesel, or a Legend! (Yeah, right. ::) ) Finally, she says I don't have to send my broken one in, so that's cool (might've been a different story had I not provided photographic proof of the malfunction).
Anyhoo, that's it for now.
-
Sounds like a pretty happy ending mate :), and at least Gerber manned up to there mistake and are willing to compensate you :)
-
Tally-ho! Me again.
I think I may have come up with a theory or two about what went wrong with my Flik. It may not be the pliers' casting's fault (at least, not entirely).
When I learned tonight that I didn't have to send back my "lemon," I thought I'd take it appart to see if I could spot what really went wrong. Turns out there ain't that much to it: remove the four black screws from the two plastic sliders, pull them out, and the pliers slide out of the handles (they must be in the fully closed position first).
After checking everything out and getting a fair gist of how the whole thing works, I stand by my original "assessment" that this is a really crappy design--in both execution and theory.
IMO, how reliable the whole thing works depends almost entirely on the proper functioning of four little springs. There are two per side: one torsion (which keeps the pawl in tension) and one compression (which pushes against the button to keep it raised). If ANYTHING gets in the way of any of the springs' movement and/or tension, problems are bound to occur. I believe that's what happened with mine. On my Flik's "good" side, the button's compression spring slid off freely when I removed it. BUT, on the damaged side, the spring was still "sticking" onto the button's peg (whose machining seemed a bit uneven), and it seemed to bind a little when I was compressing it up and down.
Now, was this "sticking" the initial cause of the malfunction? Maybe... Maybe not. At any rate, those two notches caused by the pawl slipping after that mortal squeeze is what finally killed it. I replaced the tight spring with a slightly larger one I had on hand, and the thing still slips.
Again, the overall design SEEMS like a good one in theory. But even if they (Gerber) were to ditch the plastic sliders in favor of metal ones... and even if they were to use super-duper, heavy-duty forged Cr-Mo steel for the pliers, it's just way too easy for small bits of sand, dirt, metal filings or even sawdust or plastic to get in there and compromise the works and potentially cause a malfunction similar to mine.
That being said, those of you who already own a Flik... if one day you "feel" something's not right when squeezing the pliers (i.e. an audible, "sickening" click that can also be felt), take the pliers out and check see if there's any foreign matter that might be interfering with the movement of the springs and/or buttons and/or pawls. Also check if the pawls' torsion springs are seated and functioning properly.
-
It's good to see Gerber have come through for you. :)
Hopefully, like they said, this was just an isolated incident and we won't be hearing too many more of these stories.
-
Sound advice mate, thanks

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



