Little Boy and Fat Man
-
:D

NICE Pair Stephen

Fat man got a good workout today. First I needed to repair the tilt on a radial arm saw. The long Phillips made getting at some recessed screws easy and I use the pliers to bend a metal pin that releases the saw for side to side movement.

It also helped me replace a plug in that powers the saw.
The last job it finished was I used the crimper in the plier head to hold a few nails while I pounded them into a gate I had to fix.
I got to keep my gloves on :D It's way to cold outside to try holding a nail with bare hands.
Now I just put on the Rebar and I'm going to warm up and relax.

post 24♋
-
the phillips on the ST300 is longer than the one of Vic Spirit and Swisstool, right?
-
@styx said:
the phillips on the ST300 is longer than the one of Vic Spirit and Swisstool, right?They are about the same length from the tabs but the whole ST300 driver from the handles is about 1cm longer than the Spirit one and I think 5mm than the SwissTool (It's in the car and I'm to lazy to go get it. :P Compared it to THIS.).



-
I used fat mans pliers to hold a piece of steel I tapped out to hold a bolt. Its part of the same saw as yesterdays table.

I also used it to remove and replace the table the saw rests on
-
CAP CRIMPER!!!

-
The cap crimpers look awesome but I feel they take away from the usability of the pliers. That is unless you actually need the cap crimpers.
-
@captain spaulding said:
The cap crimpers look awesome but I feel they take away from the usability of the pliers. That is unless you actually need the cap crimpers.I do use the cap crimper for crimping on wire connecters and I found yesterday they work well for holding freezing cold nails.
I thought that it will weaken the pliers so they are the best to test.
I doubt after using them some that Il ever break them.
Time will tell.
-
Glad you found uses for the cap crimper. Using it to hold freezing nails is a great idea.

-
Reminds me of this.
http://forum.multitool.or...ols/my-leatherman-post-2/
Nate broke his ALX that way so be careful, or not. >:D
-
@enki_ck said:
Reminds me of this.http://forum.multitool.or...ols/my-leatherman-post-2/
Nate broke his ALX that way so be careful, or not. >:D
ouch
I don't like reading that.
-
Reminds me of this.
http://forum.multitool.or...ols/my-leatherman-post-2/
Nate broke his ALX that way so be careful, or not. >:D
ouch
I don't like reading that.
This was the thread that preceded it.
http://forum.multitool.org/leatherman-tools/leatherman-post-1/
-
Reminds me of this.
http://forum.multitool.or...ols/my-leatherman-post-2/
Nate broke his ALX that way so be careful, or not. >:D
ouch
I don't like reading that.
This was the thread that preceded it.
now I think you're just trying to make me nervous lol
I promise I won't hit the plier jaws or grip nails to hard holding them. :salute:
-
Joel (hope I got it right, cause I always think you're Jor-El), how would you rank on the scale of accepting challenges from 1 to redneck?
'Cause I've got one for you. every time you pull out the ST300, you gotta announce it with nana nana nana nana nana fat man for an entire day.... yes i've been drinking today
-
@styx said:
Joel (hope I got it right, cause I always think you're Jor-El), how would you rank on the scale of accepting challenges from 1 to redneck?'Cause I've got one for you. every time you pull out the ST300, you gotta announce it with nana nana nana nana nana fat man for an entire day.... yes i've been drinking today
you can just call me ja
lol and no I won't be doing that lol
I think id wind up getting my ass kicked on the job site if I did. Lol
-
then probably better not. someone might take it wrong
-
Here is a quick in action shot of fat man eating some power wire off a furnace I'm removing from a abandon home.

one bite cuts through all the wire I've tried cutting.
-
Reminds me of this.
http://forum.multitool.or...ols/my-leatherman-post-2/
Nate broke his ALX that way so be careful, or not. >:D
ouch
I don't like reading that.
This was the thread that preceded it.
http://forum.multitool.org/leatherman-tools/leatherman-post-1/
now I think you're just trying to make me nervous lol
I promise I won't hit the plier jaws or grip nails to hard holding them.

Neh, not trying to make you nervous. :D Just letting you know of the risks. I actually find it a great idea to utilize the cap crimpers, especially in small areas where you can't grip the nail without them.
-
[quote author=enki_ck link=topic=49288.msg825877#msg825877 date=1389230219]
Reminds me of this.http://forum.multitool.or...ols/my-leatherman-post-2/
Nate broke his ALX that way so be careful, or not. >:D
ouch
I don't like reading that.
This was the thread that preceded it.
now I think you're just trying to make me nervous lol
I promise I won't hit the plier jaws or grip nails to hard holding them. :salute:
Neh, not trying to make you nervous. :D Just letting you know of the risks. I actually find it a great idea to utilize the cap crimpers, especially in small areas where you can't grip the nail without them.
[/quote]Don't worry about it Man
I appreciate knowing.
I've always been a worrier. I doubt Il every change. :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
