Little Boy and Fat Man
-
Fat man cuts wire very very well. I just wired in a new water meter for a tenant.
I used the medium flat head and the Phillips also. Everything about this tool I like so far.id buy one to replace this one of I lost it. Its that good of a tool.
the only other super tool I've used was the original.
the new 300 is a great user its very similar to the original but with replaceable wire cutters and a locking tab instead of having to open one tool to close another.
**I'm almost ready to say this is the best multitool for real work.
Almost. **
I still have to use it more before I can say for sure.The ST300 Rocks. That I will say :D
Better than your OHT that you used for a month? :)
Yup better than the oht mike. :)
-
Fat man cuts wire very very well. I just wired in a new water meter for a tenant.
I used the medium flat head and the Phillips also. Everything about this tool I like so far.id buy one to replace this one of I lost it. Its that good of a tool.
the only other super tool I've used was the original.
the new 300 is a great user its very similar to the original but with replaceable wire cutters and a locking tab instead of having to open one tool to close another.
**I'm almost ready to say this is the best multitool for real work.
Almost. **
I still have to use it more before I can say for sure.The ST300 Rocks. That I will say :D
Better than your OHT that you used for a month? :)
Yup better than the oht mike. :)
I thought you would say so! LOL
The tools are kinda small on the OHT, at least IMO and the ST300 looks like it can take a beating and dish one out! :D
-
Glad you're doing well with the ST300 Joel
I'm assuming the Rebar isn't getting as much use since you have it as your off work tool?I'm sure Il give the rebar a good workout.
I get stuck working when I'm off .
when who knows. :)
Good, I look forward to seeing what you put it through

-
C'mon J, don't make it easy on the Rebar just because the ST300 looks like the original ST has been doing steroids and pumping iron for the past 10 years.
On the other hand it's odd how you're one of the few people that cam make me drool over a Leatherman. For me that's like drooling over a salad in a steak house
-

:D

-
:D

NICE Pair Stephen

Fat man got a good workout today. First I needed to repair the tilt on a radial arm saw. The long Phillips made getting at some recessed screws easy and I use the pliers to bend a metal pin that releases the saw for side to side movement.

It also helped me replace a plug in that powers the saw.
The last job it finished was I used the crimper in the plier head to hold a few nails while I pounded them into a gate I had to fix.
I got to keep my gloves on :D It's way to cold outside to try holding a nail with bare hands.
Now I just put on the Rebar and I'm going to warm up and relax.

post 24♋
-
the phillips on the ST300 is longer than the one of Vic Spirit and Swisstool, right?
-
@styx said:
the phillips on the ST300 is longer than the one of Vic Spirit and Swisstool, right?They are about the same length from the tabs but the whole ST300 driver from the handles is about 1cm longer than the Spirit one and I think 5mm than the SwissTool (It's in the car and I'm to lazy to go get it. :P Compared it to THIS.).



-
I used fat mans pliers to hold a piece of steel I tapped out to hold a bolt. Its part of the same saw as yesterdays table.

I also used it to remove and replace the table the saw rests on
-
CAP CRIMPER!!!

-
The cap crimpers look awesome but I feel they take away from the usability of the pliers. That is unless you actually need the cap crimpers.
-
@captain spaulding said:
The cap crimpers look awesome but I feel they take away from the usability of the pliers. That is unless you actually need the cap crimpers.I do use the cap crimper for crimping on wire connecters and I found yesterday they work well for holding freezing cold nails.
I thought that it will weaken the pliers so they are the best to test.
I doubt after using them some that Il ever break them.
Time will tell.
-
Glad you found uses for the cap crimper. Using it to hold freezing nails is a great idea.

-
Reminds me of this.
http://forum.multitool.or...ols/my-leatherman-post-2/
Nate broke his ALX that way so be careful, or not. >:D
-
@enki_ck said:
Reminds me of this.http://forum.multitool.or...ols/my-leatherman-post-2/
Nate broke his ALX that way so be careful, or not. >:D
ouch
I don't like reading that.
-
Reminds me of this.
http://forum.multitool.or...ols/my-leatherman-post-2/
Nate broke his ALX that way so be careful, or not. >:D
ouch
I don't like reading that.
This was the thread that preceded it.
-
Reminds me of this.
http://forum.multitool.or...ols/my-leatherman-post-2/
Nate broke his ALX that way so be careful, or not. >:D
ouch
I don't like reading that.
This was the thread that preceded it.
now I think you're just trying to make me nervous lol
I promise I won't hit the plier jaws or grip nails to hard holding them. :salute:
-
Joel (hope I got it right, cause I always think you're Jor-El), how would you rank on the scale of accepting challenges from 1 to redneck?
'Cause I've got one for you. every time you pull out the ST300, you gotta announce it with nana nana nana nana nana fat man for an entire day.... yes i've been drinking today
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login